NRS Healthcare N29222 User manual

1
USER INSTRUCTIONS
TRANSIT LITE SELF PROPELLED
WHEELCHAIR
N29222 Transit Lite - Blue N43723 Transit Lite - Silver
General Safety Warning
Please make sure that you read and follow these
instructions carefully. Keep these instructions in
a safe place for future reference.
Maximum User Weight
17st
110kg
1. INTENDED USE
The Transit Lite Self Propelled Wheelchair is designed to transport a person either self propelled or with
assistance from a carer. It can be used both indoor and outdoor. It is not intended for use as a seat in a
motor vehicle.
2. SAFETY
Warning: The maximum user weight must not be
more than 110Kg (17st).
This Wheel chair is designed for single occupancy
only, do not use it to transport more than one person.
Outdoor: Steep gradients should be avoided,
assistance is recommended if you are negotiating
slopes steeper than ten degrees.
If attempting gradients, or using a ramp it is important
to be sure of your own capabilities, NRS recommend
that you consult a Healthcare Professional for advice
before use.
Always maintain a constant slow speed on gradients.
Use the rear wheel hand rims to control all movement,
alternatively an attendant can assist using the rear
handles.
Do not reverse down a gradient.
Avoid rugged/uneven terrain.
Indoor: Be aware of local hazards, for example,
obstructions on the floor, narrow doorways high
thresholds etc.
Do not use on escalators.
Before transferring into or out of the wheelchair
ensure the brakes are in the locked position.
Do not stand on the footplates.
When seated in the wheelchair ensure you are
comfortable and your centre of gravity is in the centre
of the seat.
Take care when performing tasks which move your
centre of gravity. Never reach so far that it requires
you to shift in the seat or bend forward over the
front wheels. If you do need to reach forward always
ensure the front wheels are facing outwards and are
locked before attempting any manoeuvre, this will
increase the wheels footprint.
Users feet must always be on the footplates when
the wheelchair is moving.
Take care when ascending or descending a kerb.
When mounting a kerb, approach forward facing, the
attendant should then use the stepper tubes, located
behind the rear axles, to raise the front wheels onto
the raised kerb, then roll the rear wheels up the kerb
lifting as required.
When descending a kerb the front wheels should
be lined up parallel with the front edge of the kerb,
then using the stepper tubes the attendant raises
the front wheels slightly to the balancing point of the
chair and then gently lower the rear wheels over and
down the kerb Do not raise the front wheels by using
the handles only - Always use the stepper tubes.

2
If you need to stop on an incline apply both brakes
gently, avoid sudden movements, similarly when
starting avoid sudden movements as both of these
situations could cause instability because of the
backward angle of the chair.
Apply brakes evenly as any movement sideways
could cause instability.
Avoid changing direction on a slope as this will
increase the risk of the wheelchair tipping.
Do not use as seat in a motorised vehicle
If you are unsure about any of the safety precautions
highlighted we would recommend seeking advice
from a Healthcare professional.
3. UNPACKING
Remove the packaging and check all parts carefully.
Contact your supplier immediately if parts are
missing or damaged and do not try and assemble.
3.1 Contents:
1. Wheelchair (folded)
2. Calf Strap
3. Footrest Assembly (x2)
4. Multi Function Spanner
5. Allen Key
6. User Instructions
7. Rear Wheel (x2)
8. Rear Axle (x2)
4. SPECIFICATION
Maximum User Weight: 110kg (17st)
Product Weight: 14kg
5. ASSEMBLY/INSTALLATION
Before assembling the wheelchair ensure the floor
area will not damage the vinyl armrests, If necessary
place a protective cover on the floor.
Remove all parts from the packaging and place the
chair upside down resting on the armrest - take care
not to damage the vinyl cover on the armrests.
Assemble the wheel axle to the wheel as shown in
diagram 2A. Note The axle knob (black) at the end
of the axle needs to be pressed in - this will retract
the spring locking buttons and allow the axle to pass
through the wheel hub.
Align the wheel hub with the hub on the frame and
push the axle through the frame hub. Diagram 2.
Release the axle knob and the locking buttons will
spring outwards locking the assembly together.
Diagram 2C.
Pull on the wheel to ensure it is locked correctly in
place.
Repeat for the other wheel.
Place the wheelchair on its wheels and fully open.
Raise the hinged handles to the upright position until
the spring pins “click” and lock into position on both
sides.
Assemble the footrests to the chair frame by
engaging the holes in the footrest bracket onto the
two hinge pins on the frame, this can be done more
easily if the footrest is pointing outwards, at a right
angle with the chair side. Rotate through 90 degrees
until the chrome footrest clip springs into position.
When using for the first time, it is important to
ensure the correct seating position, this may need
the footrest height to be adjusted. To do this slacken
the hexagon head screw, on the underside of each

3
footrest, with the spanner (provided). Slide the
inner tube up or down to the required position and
retighten.
Fit the calf strap as shown and secure with the hook
and loop fasteners.
Check the brakes are functioning correctly. If not,
refer to the maintenance section for correct brake
adjustment.
The wheelchair is now ready to use.
6. IN USE
6.1 Folding the wheelchair
Ensure footrests are facing forward and footplates
are in the upright position, then simply pull up the
two handles on either side of the seat, see picture
above, the wheelchair can be carried using these
handles.
For transportation and storage it is recommended
that the footrests are removed & the handles are
folded down.
Remove the Calf Strap by pulling apart the hook and
loop fasteners.
Footrest removal: pull the chrome footrest clip
towards the centre of the wheelchair and lift the
footrest offthe locating pins.
Handle folding: Pull the two plastic handle clips
backwards and fold the handles.
Rear Wheel Removal - The rear wheels are
easily removed by pushing in the axle knob and,
simultaneously, pulling the wheel away from the
frame.
6.2 Brake operation
The brakes on this wheelchair are for parking only
and should not be used for slowing down. To slow
down use reverse pressure on the wheel hand rims
and/or the handles to slow down.
To activate the parking brake push both brake levers
fully forward.
To release pull the levers backwards.
If you apply the brake, and the wheels still move, stop
use immediately. Do not use again until the brakes
have been checked. Refer to the maintenance
section.
7. MAINTENANCE
Note all tyres on this wheelchair are solid and do not
need inflating.
Regularly check for wear and tear and that all screws
and fixings are securely fastened.
Worn upholstery must be replaced.
The brakes on this wheelchair are factory set and
should not need adjusting, however if the brakes are
not operating correctly and require adjusting contact
you dealer immediately.
8. CLEANING INSTRUCTIONS.
Clean all parts regularly, wipe down with water and
mild cleanser using a soft, non abrasive cloth.
Dry with a soft, clean, non abrasive, dry cloth.
Ensure there is no build up of dirt or debris around
the axle, brakes and wheels.
Do not use cleaning agents containing phenol or
chlorine, as this may damage the product surfaces.
Lubricate with 3-in-l oil periodically or if wheels begin
to squeak.
9. PRODUCT GUARANTEE
NRS Healthcare guarantee this product for a period
of 12 months, from the date of purchase, against
faulty materials and workmanship.
This guarantee does not cover; fair wear & tear,
abuse, misuse, interference or tampering with any
part of the product.
Any guarantee issued by NRS Healthcare does not
affect your statutory rights.
If you have any problems with our products, please
contact us at the address below.
If you have experienced an injury, contact us but feel
free to contact the Medical and Healthcare products
Regulatory Agency at:
[email protected].uk

4
NRS HEALTHCARE Sherwood House,
Cartwright Way, Forest Business Park, Bardon
Hill, Coalville, Leicestershire, LE67 1UB, UK.
NRS HEALTHCARE 4C Altona Road, Blaris
Industrial Estate, Lisburn, Co Antrim,
Northern Ireland BT27 5QB
Tel: Customer Services: 0345 121 8111 Email: [email protected]
NRS Healthcare is a leading supplier of community equipment and daily living aids.
Please visit one of our websites to view our full range of products:
www.healthcarepro.co.uk or www.completecareshop.co.uk
N29222-UI-3 26-07-2021