NTI ENVIROMUX Series User manual

MAN238 Rev Date 9/9/2022
E-IMD-LCV2(P)
Low-Cost Infrared Motion Sensor
Installation and Operation Manual
ENVIROMUX®Series

TRADEMARK
ENVIROMUX and the NTI logo are registered trademarks of Network Technologies Inc in the U.S. and other countries. All other
brand names and trademarks or registered trademarks are the property of their respective owners.
COPYRIGHT
Copyright © 2018-2022 by Network Technologies Inc. All rights reserved. No part of this publication may be reproduced, stored
in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written consent of Network Technologies Inc, 1275 Danner Drive, Aurora, Ohio 44202.
CHANGES
The material in this guide is for information only and is subject to change without notice. Network Technologies Inc reserves the
right to make changes in the product design without reservation and without notification to its users.

TABLE OF CONTENTS
Introduction......................................................................................................................................................................1
Materials..........................................................................................................................................................................1
Features ..........................................................................................................................................................................2
Installation .......................................................................................................................................................................3
Operation.........................................................................................................................................................................5
Alarm Delay.................................................................................................................................................................5
Test..............................................................................................................................................................................5
Technical Specifications..................................................................................................................................................6
Warranty Information.......................................................................................................................................................7

NTI INFRARED MOTION DETECTOR
1
INTRODUCTION
The E-IMD-LCV2 is a low-cost infrared motion sensor with advanced technology in signal processing and provided with high
detection ability with protection against false alarms. When used with the ENVIROMUX Series Environment Monitoring Systems it
will provide indication and alerts when it detects human motion/intruders that pass through the detection area.
Features
Registers movement in area covered: 39x39 ft (12x12 m), 110°wide.
Condition display via LED.
Intelligent logic control prevents false alarms.
Wall mount or hang in a corner.
Good RFI protection.
Screw terminal
To connect to the digital inputs use a 22 AWG 2-wire cable. Connect the other end to the sensor screw terminal.
Maximum cable length: 1,000 ft (305 m).
Includes mounting bracket for installing the sensor to a ceiling or wall.
Powered by E-16D/5D/2D
oWhen separate power supply (12V/1A) is needed order E-IMD-LCV2P(When used with E-MICRO, E-MINI-
LXO, etc)
MATERIALS
Materials supplied with this kit:
NTI E-IMD-LCV2 Infrared Motion Detector
110-240VAC, 50 or 60Hz-12VDC/1A AC Adapter (E-IMD-LCV2P model only)
Country-specific Line Cord (E-IMD-LCV2P model only)
Mounting hardware
URL Slip with path to this manual

NTI INFRARED MOTION DETECTOR
2
FEATURES
# ITEM DESCRIPTION
1 Sensor Infrared Motion Sensor
2 Switch Tamper switch - NC
3 Jumper blocks For placement of delay jumper
4 LED Illuminates Red to indicate when motion is sensed
5Wire Terminal Block For connection of ENVIROMUX and power wires
6 Hole in Case Pre-drilled hole for passage of wires into case

NTI INFRARED MOTION DETECTOR
3
INSTALLATION
1. Select a location suitable for installation:
Stationary surface at least 86 inches (2.2m) above the ground.
Away from air movement source (air should be static/stable)
Away from a window (no direct sunlight)
Away from a heat or cold source (temperature should not be changing significantly)
2. Mount E-IMD-LCV2(P) using installation bracket provided.
3. Remove the screw from the bottom of the case and remove the cover.
4.Pass wires through pre-drilled hole in the case.
5. Connect wires to terminal block as per appropriate wiring diagram below.

NTI INFRARED MOTION DETECTOR
4

NTI INFRARED MOTION DETECTOR
5
OPERATION
Alarm Delay
The E-IMD-LCV2(P) is equipped with three jumper positions to choose from. Place the provided jumper in one of the following
positions:
15 MIN- After an initial alert is sent from the first motion sensed, there will be a 15 minute delay before the sensor will react to any
additional motion and send another alert. The sensor will send an alert every 15 minutes if it continues to sense motion. All
motion sensed between the 15 minute intervals will be ignored.
10 SEC- After an initial alert is sent from the first motion sensed, there will be a 10 second delay before the sensor will react to
any additional motion and send another alert. The sensor will send an alert every 10 seconds if it continues to sense motion. All
motion sensed between the 10 second intervals will be ignored.
Nor- There will be no delay. When the sensor senses movement, an alert will be immediately sent.
Test
When performing a product test, make sure the delay jumper is on the "Nor" pins for an immediate alert to be sent.
With the E-IMD-LCV2(P) connected to the ENVIROMUX (and power supply connected as applicable), the detector should be
ready to sense. Walking within the sensed range of the detector should provide an alert message to any user configured to
receive it. When sensed, the Red LED on the detector should illuminate for at least 2 seconds.

NTI INFRARED MOTION DETECTOR
6
TECHNICAL SPECIFICATIONS
Operating voltage 8-15VDC
Current Consumption less than 20mA (@12VDC)
Operating temperature -10 to 50˚C
Operating humidity 0-95% RH non-condensing
Mounting mode wall-mounted
Mounting height 2.2m
Detecting distance 12m
Detecting angle 110 degree
Alarm output NO/NC (optional)
Alarm Indicator Red LED
Anti-dismantle (Tamper)
switch NC
Size (In.) WxDxH 2.07 x 3.54 x 1.74 In.
(52.6 x 90 x 44.3mm)

NTI INFRARED MOTION DETECTOR
7
WARRANTY INFORMATION
The warranty period on this product (parts and labor) is two (2) years from the date of purchase. Please contact Network
Technologies Inc at [phone] (800-RGB-TECH) or [phone] or visit our website at http://www.networktechinc.com for
information regarding repairs and/or returns. A return authorization number is required for all repairs/returns.
MAN238 Rev. 09/9/22