NuAire MRXBOX95-WH1 Instruction Manual

1.0 Introduction
The WH1 wall mounted range of units is designed to provide
mechanical supply and extract ventilation with heat recovery.
The unit is fitted with two independent fans. Each fan has full speed
control for background and boost ventilation rates.
To recover heat from the extract air the heat exchanger block is
utilised. The heat exchanger can recover up to 95% of the normally
wasted heat.
If the unit has integral automatic HX bypass (AB models only)
The bypass damper shall open automatically via a wax actuator
allowing the air to bypass the heat exchanger to deliver fresh
filtered air during the warmer months.
2.0 Installation
Installation must be carried out by competent personnel in
accordance with the appropriate authority and conforming
to all statutory governing regulations. All mains wiring must be in
accordance with the current I.E.E. Regulations, or the appropriate
standards. Ensure that the mains supply (Voltage, Frequency and
Phase) complies with the rating label.
Please note a clear working space is required around the installed
unit to allow the cover to be removed and provide sufficient access
for maintenance such as filter change.
Please allow a minimum of 430mm in front of the MRXBOX95-WH1
unit and 360m in front of the MRXBOX95AB-WH1.
The fan must be installed indoors, on a suitable wall away from
direct sources of frost, heat, water spray or moisture generation.
For a vibration-free result the unit must be mounted to a solid wall.
2.1 Wall Mounting the MVHR Unit
The unit is designed for wall mounting, only on a solid wall.
A gypsum block or stud/plasterboard wall will not suffice.
1. One part of the mounting bracket (supplied) should be offered up
to the wall, ensuring it’s located horizontally. Mark the fixing points
through the pre drilled holes in the bracket and install with screws
(by others), ensuring the interlock side is at the top, (fig. 3).
Figure 3. Fixing the mounting bracket to the wall.
2. Install the unit on the wall by ensuring the bracket fixed to the
rear of the unit interlocks over the wall mounted bracket (fig. 4).
Figure 4. Mounting the unit on the wall mounted bracket.
Note: Care must be taken to ensure the unit is installed true in
all 3 dimensions. Failure to do so may result in overflow from the
internal condensation drip tray.
(See overleaf for mounting option details, on walls or
in the loft space).
The un t must rema n sw tched on at all t mes to ma nta n
vent lat on w th n the dwell ng. Turn ng the un t off w ll cause
long term damage to the un t and bu ld ng fabr c.
Th s appl ance s not ntended for use by persons ( nclud ng
ch ldren) w th reduced phys cal, sensory or mental capab l t es,
or lack of exper ence and knowledge, unless they have been
g ven superv s on or nstruct on concern ng the use of the
appl ance by a person for the r safety. Ch ldren should be
superv sed so that they do not play w th the appl ance.
Installation and Maintenance
MRXBOX95-WH1 (Standard Unit)
MRXBOX95-WH1-OH (Opposite hand Unit)
MRXBOX95AB-WH1 (Standard Unit)
MRXBOX95AB-WH1-OH (Opposite hand Unit)
Mechanical Ventilation Units with Heat Recovery for Wall Mounting
127. 11. 17. Leaflet Number 671686
Extract air
from house
Intake air
from outside
Exhaust air
from house
to outside Supply air
to house
Figure 1. Airflow through unit (Standard unit).
Figure 2. Airflow through OH unit (Opposite hand unit).
Intake air
from outside
Extract air
from house
Supply air
to house Exhaust air
from house
to outside
The EMC Directive
2014/30/EU
The Low Voltage
Directive
2014/35/EU
Nuaire: A Trading Division of Polypipe Limited Western Industrial Estate Caerphilly United Kingdom CF83 1NA
T: 029 2088 5911 F: 029 2088 7033 E: [email protected] W: www.nuaire.co.uk

227. 11. 17. Leaflet Number 671686
Installation and Maintenance The WH1 Wall Mounted Range of Units
2.2 Option 1: Wall Mounting
The MVHR unit fixed to a solid wall construction using
the mounting bracket provided.
Figure 5. Typical example of a cupboard mounted unit (Standard unit)
fixed to a block work wall.
Option 2: Wall Mounting
If it is not practical to use a solid wall, the MVHR unit
should be fixed to a stud partition with a 25mm
minimum thickness MDF panel solidly fixed behind the
plasterboard.
If fixing to a stud wall the MDF panel should extend, width wise, over
a minimum of 3 vertical studs with centres of no more than 400mm.
Add additional vertical supports if necessary. Height wise, ideally, the
MDF panel should extend from floor to ceiling but as a minimum
should be a least 2m high.
Fix the mounting bracket to the wall (as fig 3) and use the wall
mounted bracket to mount the unit on (as shown in fig 4).
Figure 6. Typical example of a cupboard mounted unit (Standard unit)
fixed to a stud partition with the MDF panel fixed behind the plaster-
board.
2.3 Option 1: Loft Space Mounting
The MVHR unit should be positioned on a tank stand
using the Nuaire Anti-vibration tray assembly discarding
the angle brackets.
The Nuaire Anti-vibration tray assembly (to be purchased separately)
Part No. AV-WH1.
Figure 7a. Typical example of tray assembly used for mounting in a
loft space.
Option 2: Loft Space Mounting
The MVHR unit should be positioned on a 25mm
minimum thickness MDF panel that is vertically fixed
across the roof trusses to form a solid false wall.
Add additional vertical supports if necessary. Use the Nuaire Anti-
vibration tray assembly including the angle brackets (to be purchased
separately) Part No. AV-WH1.
Figure 7b. Typical example of tray assembly and wall angle brackets used
for mounting in a loft space on 25mm vertically fixed MDF board.
Ducting in the
ceiling void.
Side view of unit
mounted on the
block wall in a
cupboard.
MVHR-DRAIN
Condensate drain,
uninsulated drain
pipe with min 5o
fall running to SVP.
Valve in ceiling.
Ducting in the
ceiling void.
Side view of unit
mounted in a
cupboard fixed to
a stud partition
with the 25mm
MDF fixed behind
the plasterboard.
MVHR-DRAIN
Condensate drain,
uninsulated drain
pipe with min 5o
fall running to SVP.
Valve in ceiling.

327. 11. 17. Leaflet Number 671686
Installation and Maintenance The WH1 Wall Mounted Range of Units
2.3 Condensate Drain
1. The condensate must be discharged under a water level in a
U-trap drainpipe or an alternative drain method which acts as an
airlock.
2. This condensate discharge connection is suitable for 21.5mm dia.
overflow pipe. Solvent cement should be used to make the joint.
3. If using a U-trap please ensure the U-trap has been filled to a
suitable level of water to avoid any air locks.
4. If the condensation pipe is fitted in an unheated space the pipe
should be in insulated to prevent freezing.
Nuaire recommend MVHR-DRAIN be used as the primary
condensate take-off. (see figure 8b and 8C.
2.4 Extract/input areas
The unit is designed to extract air from all wet rooms e.g. bathroom,
kitchen, en-suite, utility room (with sink).
WC’s do not need to be ventilated if openable windows are fitted.
Supply air should be to all habitable rooms e.g. bedrooms and lounge.
Extract / input grilles should be adjustable valve types (not supplied).
External grilles to have a minimum free area of 12,250 sq mm.
2.5 Ducting
Before commencing ducting installation reference should be made to
building regulations document “Domestic ventilation compliance
guide”. This document supports ADF2010 and details installation,
testing and commissioning of all ventilation systems.
It is recommended that rigid ducting be used at all times.
Flexible ducting has a very high resistance and it is impossible to
calculate how much resistance will be on a system if used.
If used the flexible ducting must be kept to a minimum and should
always be pulled taut. A maximum of 300mm should be used on each
leg.
To prevent condensation on the outside of the outside air inlet duct
and the air outlet duct from the unit, these ducts should be
insulated.
Ducting must be installed in such a way that resistance to airflow is
minimised. Bends should be kept to a minimum.
A minimum distance of 300mm between the appliance and any
bends in ductwork is recommended.
Ideally 150mm diameter or 204 x 60mm rectangular ducting should
be used. (Refer to dwelling design drawing, figure 10a and 10b on
page 5 for further information).
Ducting joints must be sealed with silicone type sealant and shall be
adequately and reliably fixed to the appliance.
2.6 Ventilation flow rates
Table 1.
ADF 2010 – Extract ventilation rates
Room Min high rate Min low rate
Kitchen 13 l/s
Utility room 8 l/s
Bathroom 8 l/s
Sanitary
accommodation 6 l/s
Table 2.
Whole dwelling ventilation rates
Number of bedrooms in dwelling
12345
Whole 13 17 21 25 29
dwelling
ventilation
rate l/s
1, 2
Notes:
1, In addition, the minimum ventilation rate be should be not less
than 0.3 l/s per m2of internal floor area.
(This includes all floors, e.g. for a two-story building add the
ground and first floor areas).
2, This is based on two occupants in the main bedroom and a
single occupant in all other bedrooms. This should be used as the
default value. If a greater level of occupancy is expected add 4 l/s
per occupant.
Figure 8a. Wet option.
Condensate pipe
connection to unit and
a typical example of
a “U” trap drainpipe.
(Standard configuration
only).
Figure 8b. MVHR-DRAIN option.
Condensate drain, uninsulated drain
pipe with min 5ofall running to SVP.
Min 5oDrop
Collar
Total extract rate should be
at least the whole dwelling
ventilation rate given in
table 2.
To SVP
“T” piece
MVHR Drain
To unit
To CONTRAP
Figure 8c. IM ORTANT: When using a “T” iece to connect the CONTRA
drainage and the MVHR drain pipework the MVHR drain must always be
fitted before the “T” iece to prevent condensate from feeding back
into the MVHR system.
Any a r ntake term nal MUST be nstalled n accordance w th
the appropr ate regulat on.
As a gu de, the BS5440 ser es of Br t sh Standards deals w th
th s ssue and currently states that an a r ntake must be at a
m n mum d stance of 300mm from a gas bo ler balanced flue.
Installers are adv sed to be aware of the requ rements of th s
standard when nstall ng ‘through the wall’ supply a r duct ng.

2.7 ADF 2010 Ventilation Calculations
Design of MVHR Systems
The MVHR system has been sized for the winter period. Additional
ventilation may be required during the warmer months and it has
been assumed that the provisions for purge ventilation (e.g. openable
windows) could be used.
Step 1: For any design air permeability, determine the whole dwelling
ventilation supply rate from Table 2.
As an alternative where the design air permeability is intended to be
leakier than (>) 5m3/(h.m2) 50 Pa, allow for infiltration for all
dwelling types by subtracting from the whole dwelling ventilation
supply rate from Table 2; 0.04 x gross internal volume of the dwelling
heated space (m3).
Step 2: Calculate the whole dwelling extract ventilation rate by
summing the individual room rates for ‘minimum high rate’ from
Table 1.
(For sanitary accommmodation only, as an alternative, the purge
ventilation provisions given in ADF 2010 can be used where security
is not an issue. In this case ‘minimum high extract rate’ for the
sanitary accommodation should be omitted from the step 2
calculation).
Step 3: The required airflow rates are as follows:
nthe maximum whole dwelling extract ventilation rate (e.g. boost)
should be at least the greater of step 1 and step 2.
Note that the maximum individual room extract rate should be
at least those given in table 1. for minimum high rate.
nthe minimum air supply rate should be at least the whole building
ventilation rate found in step 1.
For Scotland refer to BRE Digest 398.
For further information refer to “Domestic Ventilation Compliance
Guide” www.planningportal.gov.uk/buildingregulations/approved
documents/partl/compliance
427. 11. 17. Leaflet Number 671686
Installation and Maintenance The WH1 Wall Mounted Range of Units
658
623
Mounting
bracket
432
Side viewView from front
Figure 9.
3.0 Dimensions
View from top
Spigots
4 x 150mm dia.
458
16
120
226
226

527. 11. 17. Leaflet Number 671686
Installation and Maintenance The WH1 Wall Mounted Range of Units
4.0 Ducting Arrangements - Standard Configuration
Air supply
to lounge
via Air Valve
in ceilings.
Extract air
from
kitchen/
bathroom
via Air Valve
in ceilings.
Minimum distance as specified
in building regulations.
Exhaust air from
kitchen/bathroom to
outside via louvre grille.
Intake air
from outside
via louvre grille.
All duct between MVHR
unit and atmosphere to
be insulated*.
Exhaust air from
kitchen/bathroom to
outside via air brick.
Intake air
from outside
via air brick.
All duct between MVHR
unit and atmosphere to
be insulated*.
*Insulated
supply duct.
*Insulated
supply duct.
Air supply
to lounge
via Air Valve
in ceilings.
Extract
air from
kitchen/
bathroom
via Air Valve
in ceilings.
Air supply
to bedrooms
via Air Valve
in ceilings.
Top of ceiling void.
Top of ceiling void.
Nuaire wall
mounted unit.
Air supply to
bedrooms
via Air Valve
in ceilings.
Nuaire wall
mounted unit.
MVHR-DRAIN
Condensate drain, uninsulated
drain pipe with min 5ofall running to SVP.
MVHR-DRAIN
Condensate drain, uninsulated
drain pipe with min 5ofall running to SVP.
*Insulated
extract duct.
*Insulated
extract duct.
Minimum distance as specified
in building regulations.
Figure 10a. Typical ducted arrangement for a wall mounted unit using circular ducting.
Figure 10b. Typical ducted arrangement for a wall mounted unit using rectangular ducting.
ALSO FROM NUAIRE -
New range of thermal duct ng,
an all- n-one nsulated duct ng system.
(see nstallat on document 671620).

627. 11. 17. Leaflet Number 671686
Installation and Maintenance The WH1 Wall Mounted Range of Units
For good EMC engineering practice, any sensor cables or
switched live cables should not be placed within 50mm of
other cables or on the same metal cable tray as other cables.
5.0 Electrical Connection
Please note: the electrical connection of the unit must be be carried
out by a qualified electrician.
The unit is supplied with a flexible cord for connection to the mains
supply.
Electrical details:-
Voltage: 240V 1ph 50Hz
Consumption: WH1 - 1.3 Amp
Fuse rating: 3 Amp
NOTE This unit must be earthed.
The cable from the mains power supply should be connected
to a fixed wiring installation, via a fused isolator, in
accordance with current IEE wiring regulations.
Fuse 2A
MAINS
230V
50Hz
Room
light
Light
switch
(Double
Pole)
N
L
3 Pole
isolator
Kitchen switch
Blue
Brown
Black
Optional speed 3 switch
Supply cord
from unit
Grey
Green/yellow
Unit serving kitchen and bathroom
Figure 12.
Unit serving kitchen and two bathrooms
Figure 13.
SWL2 L SWL1 L N
CN7 EXTRACT CN6 SUPPLY
BLU
WHI
YEL
RED
SUPPLY
BYPASS
SUPPLY FAN
EXTRACT FAN
B
L
U
B
R
N
B
R
N
B
L
U
EXTRACT FAN
B
L
U
B
R
N
EXTERNAL PUMP
BLU
WHI
YELI
RED
FAIL
CN8
TH1 TH2
L N
CN5
Connection to Remote Fail
Indicator Ref: MRXBOX95-RFI
(Optional)
3
2
Figure 11a.
Note: Wiring is for reference
purposes only as the connections
in fig. 11a are factory fitted.
The unit is pre-wired with a
2 metre fly lead.
Disconnection from the
supply mains must be
incorporated within the
fixed wiring in accordance
with the wiring regulations
and shall have a minimum
contact separation
of 3mm.
Disconnection from the
supply mains must be
incorporated within the
fixed wiring in accordance
with the wiring regulations
and shall have a minimum
contact separation
of 3mm.
Figure 11b.
View of the base on the unit, showing the
position of the connector for Ecosmart devices
located next to cable entry.
Connector for
Ecosmart devices Power Cable
Fuse 2A
MAINS
230V
50Hz
Room
lights
Light
switches
(Double
Pole)
N
L
3 Pole
isolator
Kitchen switch
Green/yellow
Blue
Brown
Black
Supply cord
from unit
Optional speed 3 switch
Grey
5.1 Optional Controls For further information contact Nuaire on 029 2085 8400.
If more than one Ecosmart sensor is required
please use MRXBOX- B and refer to leaflet
No. 671700 for installation instructions.
Supply Supply Extract Extract
Speed1 Speed2 Speed1 Speed2

727. 11. 17. Leaflet Number 671686
Installation and Maintenance The WH1 Wall Mounted Range of Units
Isolation - Before commencing work make sure that the
unit, switched live and Nuaire control are electrically
isolated from the mains supply and switched live supply.
The filters fitted inside the unit are protected with a
plastic film. rior to commissioning remove the covers
(figs 15/16), take off the film and replace.
Figure 14. Detail of unit control
on front panel.
(Standard configuration only).
Humidity
adjustment.
(AB unit only).
Filter covers
Figure 15. Removing the two filter covers on the front panel of
the unit.
Filter being
removed
Filter cover
Figure 16.The filters can be removed by pulling on the black tab
on the visible end of the filters.
6.0 Commissioning
2/ For the required air flow rates please refer to the design
specification for the property, follow 2.4, or refer to building
regulations ADF 2010.
3/ The unit is supplied with independent control for both normal and
boost airflows. (see fig. 14).
4/ Correct commissioning is essential to ensure the ventilation air
flowrates are met. It also ensures the unit is not over ventilating
and causing excessive power consumption.
5/ Commissioning should be carried out in accordance with building
regulations document “Domestic ventilation compliance guide”.
www.planningportal.gov.uk/building regulations/approved
documents/partf/associated
A calibrated moving vane anemometer and hood will be required
to carry out commissioning.
6/ Adjustment valves should be locked in place to prevent further
adjustment.
7/ Once commissioned the home owner / tenant should be informed
that the unit should not be adjusted as it will have a detrimental
effect on the indoor air quality and could result in condensation
and mould growth. The label covering the control has an adhesive
panel which should be removed post commissioning to prevent
tampering.
8/ Speed 1 is limited to never exceed speed 2, when commissioning
speed 2 should always be set first.
6.1 Speed 3
The unit has to ability to override both speed 1 and speed 2 to operate
the fan to maximum airflow. See wiring diagram for details of
operating this facility.
6.2 Humidity adjustment (AB unit only).
This product contains an internal humidity sensor fitted into the air-
flow extracting from the wet rooms. When the unit senses that the
humidity exceeds the set point the unit will boost to that set by the
commissioned boost speed. The set point can be found on the front of
the unit (see Fig 14) and is at its least sensitive when turned fully
clockwise. Note that the sensor is measuring humidity from all the wet
rooms at the same time and should not be relied on to solely boost the
unit. Additional switch should be used local to the wet rooms (see
wiring diagrams).
7.0 Status Indication
The status of the unit is indicated by a series of LED’s on the front
cover. The varients are listed below.
8.0 Thermal Bypass (Non AB models)
In the event of excessive outside temperatures, and to help prevent
over-heating, the supply fan will automatically reduce to a trickle
speed. Under these circumstances additional ventilation measures may
be required e.g. open windows or trickle vents (if fitted).
9.0 Maintenance/Cleaning
We recommend that the two G3 fiters are inspected after 6 months,
and replaced every 12 to 18 months. The filters can be removed from
the unit by removing the two filter covers on the front panel of the
unit. Take hold of the two circular tabs either end of the filter covers
and pull out.
The filter can now be extracted by pulling the removal loop on the
front edge of the filter. Once the filters have been inspected return
or replace them as necessary. Inspect the heat exchanger every
5 years. Generally check for damage and security of components.
Refit cover.
Speed 1
Speed 2
Speed 3
Supply Fan Fault
Extract Fan Fault
Frost Protection
Filter Change
060923
HX Bypass
(AB units only)
Speed 2
Speed 1Speed 2
Speed 1

827. 11. 17. Leaflet Number 671686
Technical or commercial considerations may, from time to time, make it necessary to alter the design, performance and
dimensions of equipment and the right is reserved to make such changes without prior notice.
10.0 Replacement of arts
Should any component need replacing Nuaire keep extensive stocks
for quick delivery. Ensure that the unit is electrically isolated,
before carrying out any work.
Note: The supply cable must be replaced by an electrically
competent person.
When ordering spare parts, please quote the serial number of the
unit and the ARC number of the purchase if possible.
(This information will be available on the fan label).
11.0 Warranty
The 5 year warranty starts from the day of delivery and includes parts
and labour for the first year and parts only for the remaining 4 years.
This warranty is void if the equipment is modified without
authorisation, is incorrectly applied, misused, disassembled, or not
installed, commissioned and maintained in accordance with the
details contained in this manual and general good practice.
The product warranty applies to the UK mainland and in accordance
with Clause 14 of our Conditions of Sale. Customers purchasing from
outside of the UK should contact Nuaire International Sales office for
further details.
12.0 After Sales
For technical assistance or further product information, including
spare parts and replacement components, please contact the After
Sales Department.
Telephone [phone]
Installation and Maintenance The WH1 Wall Mounted Range of Units