NuAire NA-E-100 Series Instruction Manual

1
nuaire.co.uk 029 2085 8400 07. 03. 17. Leaflet Number 671777
The EMC Directive
2014/30/EU
The Low Voltage Directive
2014/35/EU
NA-E-100 Range (50Hz Only)
Axial Wall/Ceiling Mounted Toilet and Bathroom Fans
Installation and Maintenance IPX4
1.0 Introduction
These high quality extractor fans are designed to provide effective
ventilation. To achieve this, please read these instructions carefully BEFORE
installing the fan unit. Failure to comply with these instructions could
reduce both the life and performance of the product and may invalidate the
warranty.
This product is suitable for use with a maximum of 1.5m of rigid ducting.
(Flexible ducting is not recommended).
This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of
the appliance in a safe way and understand the hazards involved. Cleaning and
user maintenance should not be made by children without supervision.
2.0 Installation
The installation must be completed by competent persons in accordance with
good industry practice and should conform to all governing and statutory bodies
i.e. IEE, CIBSE, HVCA etc.
Before commencing any work read the following instructions carefully and
ensure you have the necessary competency to complete the work safely.
3.0 Dimensions
Isolation - Before commencing work, make sure that the unit,
switched live and any controls are electrically isolated from the mains
supply. If in doubt, consult an electrician.
IMPORTANT
1. Select a suitable position for the fan that keeps the duct as short and as
straight as possible (ideally on the ceiling or on a wall within 400mm of the
ceiling).
2. Cut a hole in the wall to suit the outside diameter of the ducting or wall-liner.
Install the duct or wall-liner taking care to seal at both ends between it and
the wall using proprietary waterproof mastic.
3. Remove the front cover of the fan by pulling the fan back plate straight off
(Fig. 1).
4. Position the fan in the duct and mark the four retaining screw positions
through the backplate. Fit screw anchors suitable for the wall construction.
5. Remove the central terminal cover by first removing the central Posidriv®
retaining screw (Fig. 2).
6. Unclip and remove the fan wall-mounting plate (Fig. 3).
7. Complete the wiring by following the relevant wiring diagram on the
following page (for cable entry detail see Fig. 4).
8. Reassemble using these instructions in reverse.
Figure 1. Removing front cover
Figure 3. Remove wall-mounting plate
Figure 5. Fan dimensions (mm)
Figure 2. Remove central terminal cover
Figure 4. Cable entry point

2
nuaire.co.uk 029 2085 8400 07. 03. 17. Leaflet Number 671777
Installation and Maintenance NA-E-100 Axial Toilet and Bathroom Fans
PCB Details (where applicable)
Figure 9. NA-E-100 / NA-E-100T /
NA-E-100PC PCB
4.0 Wiring Instructions
Disconnection from the supply mains must be incorporated within the fixed
wiring in accordance with the wiring regulations and shall have a minimum
contact separation of 3mm in accordance with the latest edition of the IEE
Wiring Regulations.
Only NA-E-100 12V models are suitable for shower cubicles or zones 1 & 2
(in this range).
SL = 230Vac 50Hz 1ph Switched Live
L = 230Vac 50Hz 1ph Permanent Live
N = Neutral
5.0 Operation
Overrun timer adjustment – models fitted with overrun timers only
Before making any adjustments, isolate the fan from the power supply. Remove
the front cover and the body moulding. Locate the ‘jumper’ on the relevant set
of pins to achieve the desired run-on time (see Fig. 9 & 10).
Humidity adjustment – models fitted with humidistat only
All NA-E humidistat fans automatically sense a rapid change in humidity and
adjust accordingly. The humidity control does not require manual adjustment.
Humidistat fans, when energised for the first time, will run and time out as part
of the stabilising process.
6.0 Maintenance
The fan unit does not require any maintenance. However, for optimum
performance, it is advisable to remove any accumulated dust with a low power
vacuum cleaner.
Note: Installation and maintenance of the equipment must be as directed in
the instructions provided with the unit.
7.0 Warranty
The 2 year warranty starts from the day of delivery and includes parts and labour
for the first year. The remaining year covers replacement parts only.
This warranty is void if the equipment is modified without authorisation, is
incorrectly applied, misused, disassembled, or not installed, commissioned and
maintained in accordance with the details contained in this manual and general
good practice.
The product warranty applies to the UK mainland and in accordance with Clause
14 of our Conditions of Sale. Customers purchasing from outside of the UK
should contact Nuaire International Sales office for further details.
8.0 After Sales Enquiries
For technical assistance or further product information, including spare parts and
replacement components, please contact the After Sales Department.
This product is double insulated and does not require an earth conductor.
Maximum room temperature 40°C.
Technical or commercial considerations may, from time to time, make it necessary to alter the design, performance and dimensions of equipment and the right
is reserved to make such changes without prior notice.
Telephone: [phone]
[e-mail]
Unit Serving Bathroom NA-E-100
Figure 6. Wiring
Unit Serving Bathroom NA-E-100PC / NA-E-100HPC via
pullcord (Auto humidity only)
Figure 7. Wiring
Unit Serving Bathroom NA-E-100T / NA-E-100H via remote
switch (Optional timer operation)
Figure 8. Wiring
Range Description
NA-E-100 Standard
NA-E-100PC Pull cord override
NA-E-100H Humidistat and optional overrun time
NA-E-100HPC Humidistat and optional overrun time and pull cord
override
NA-E-100T Overrun timer
Figure 10. NA-E-100H /
NA-E-100HPC PCB