nuhoom MANDO 133081 User manual

1
CODING
- 133081
MANDO ASSEMBLY GUIDE
/ 4
’
Read the instructions carefully. Remove all the
wrappings , staples and straps from the carton. Refer
to the hardware and furniture part list for guidance.
Make sure that you have all the parts before you start
assembling. Place all the wooden furniture parts on a
clean, flat and soft surface, such as a carpet or
rubbermat to prevent scratches.
1
2
PART LIST
TOP PANEL
MINI FIX
4
SIDE PANEL (L)
6
SIDE PANEL (R)
7
8
QTY
3
5
MIDDLE PANEL
HARDWARE
A
B
C
D
E
F
G
14 SETS
ALLEN KEY M4 1 PC
BOTTOM PANEL
DRAWER FRONT (R)
CENTER PANEL
H
I
M6 X 5OMM
CSK CAP WOOD SCREW
A1 A2 A3
M8 X 30MM WOOD DOWEL 22 PCS 9
10
11
DRAWER BOTTOM
14" DRAWER SLIDE I1 ( L/R )
I2 ( L/R ) 2 SETS
8 PCS
1 PC
1 PC
1 PC
1 PC
1 PC
1 PC
2 PCS
M3.5 X 16MM C.B SCREW
M4 X 38MM C.B SCREW 26 PCS
24 PCS
DRAWER SIDE
DRAWER BACK
4 PCS
2 PCS
12
13
14
15
BONE PANEL 1 PC
APRON FRONT 1 PC
APRON BACK 1 PC
APRON BONE 2 PCS
DRAWER FRONT (L) 1 PC
1 PC
5/8 NAIL 16 PCS
5/8 PVC NAIL LEG 4 PCS
SCREWDRIVER HAMMER
SELF-PREPARED TOOLS: Tools below are NOT included in package.
1
2
3
4
56
7
8
9
10
10
11
13
14
15
14
12
13
14
15
14

CODING
- 133081
MANDO ASSEMBLY GUIDE
/ 42
STEP 6
STEP 4
STEP 2
STEP 5
STEP 3
STEP 1
1
3
4
56
7
8
9
10
3
4
55
3
4
6
7
1
3
4
5
6
7
- Insert hardware A1 onto panel (3), (4), (5) and (6).
(Repeat 10 times.)
- Insert hardware A2 onto panel (1), (3) and (4).
(Repeat 10 times.)
- Insert hardware B onto panel (3), (4), (5) and (6).
(Repeat 8 times.)
SCREWDRIVER
REQUIRED
* Ensure the arrows on hardware A1 point towards mounting positions.
A2
ROTATE
PRESS
A1
x10
x8
PRESS
B
x10
- Insert hardware A1 onto panel (10).
(Repeat 4 times.)
- Insert hardware A2 onto panel (8) and (9).
(Repeat 4 times.)
- Insert hardware B onto panel (7), (8) and (9).
(Repeat 8 times.)
SCREWDRIVER
REQUIRED
* Ensure the arrows on hardware A1 point towards mounting positions.
10
PRESS
A1
x4
x8
PRESS
BA2
x4
ROTATE
Fix hardware I1 (L/R) into panel (3), (4) and (5) with hardware E.
(Repeat 3 times for each hardware.)
SCREWDRIVER
REQUIRED
x3
ROTATE
x3 x3
ROTATE ROTATE
I1(L)
EEE
Third hole from the edge.First hole from the edge. Small hole at the center.
I1(R)
I1(L)
Fix hardware I1 (R) into panel (5) with hardware E.
(Repeat 3 times for each hardware.)
Third hole from the edge. First hole from the edge.
Small hole at the center.
I1(R)
x1x1x1
ROTATE
ROTATE
ROTATE
EEE
- Attach panel (3) and (4) to panel (6) and (7).
- Insert all hardware A2 into A1.
- Rotate all A1 until tight.
- Apply A3 onto all A1.
(Repeat 2 times.)
OR
HARDWARE
D
SCREWDRIVER
REQUIRED
* In this step hardware A1, A2 and B are pre-inserted.
ROTATE
Section View
x2
A1 A2
x2
PRESS
A3
- Attach panel (1) to panel (3), (4), (5) and (6).
- Insert all hardware A2 into A1.
- Rotate all A1 until tight.
- Apply A3 onto all A1.
(Repeat 8 times.)
OR
HARDWARE
D
SCREWDRIVER
REQUIRED
* In this step hardware A1, A2 and B are pre-inserted.
ROTATE
Section View
x8
A2
A1
x8 PRESS
A3

CODING
- 133081
MANDO ASSEMBLY GUIDE
/ 4
3
1
2
3
4
5
6
7
8
9
10
2
3
4
5
7
8
9
10
1
2
3
4
5
7
8
9
10
Connect panel (2) to panel (3), (4), (5) and (6)
by using hardware C and D.
(Repeat 8 times.)
ROTATE
x8
C
D
* In this step hardware B are pre-inserted.
HARDWARE
D
* In this step hardware A1, A2 and B are pre-inserted.
ROTATE
Section View
x4
A1
A2
x4 PRESS
A3
10
SCREWDRIVER
REQUIRED
ROTATE
F
x10
Assemble panel (8), (9) and (10)with panel (2)
by using hardware F.
(Repeat 10 times.)
SCREWDRIVER
REQUIRED
Hit hardware H into bottom of panel (8) and (9).
(Repeat 4 times.)
x4
HIT
H
10
1
10
STEP 10
STEP 8
STEP 9
STEP 7
- Attach panel (8) and (9) to panel (10).
- Insert all hardware A2 into A1.
- Rotate all A1 until tight.
- Apply A3 onto all A1.
(Repeat 4 times.)
OR
HARDWARE
D
SCREWDRIVER
REQUIRED

CODING
- 133081
MANDO ASSEMBLY GUIDE
/ 44
11
12
13
14
11
13
14 15
12
13
14
15
1
2
3
4
7
89
11
12
Assemble panel (14) to panel (11) or (12) and (13)
by using hardware F.
(Repeat 16 times.)
SCREWDRIVER
REQUIRED
x16
F
ROTATE
14
13
14
14
Assemble panel (15) to entire body with hardware G.
(Repeat 16 times.)
HAMMER
REQUIRED
x16
HIT
G
14
12
13
14 15
14
Assemble hardware I2 (L/R) to panel (15) by using hardware E.
(Repeat 3 times for each hardware.)
I2 (R)
I2 (L)
Hole at the center.
Third hole from the edge. Third hole from the edge.
x4
E
x4
E
x4
E
ROTATE ROTATE ROTATE
*Hardware I2 (L/R) shall be leaning against panel (11) or (12) when assembling.
SCREWDRIVER
REQUIRED
14
11
13
14
15
14
I2 (R)
I2 (L)
Put all the drawer in place along the drawer slides.
STEP 14
STEP 12
STEP 13
STEP 11