nuhoom MANDO 372048 User manual

1
CODING
- 372048
MANDO ASSEMBLY GUIDE
/ 4
’
Read the instructions carefully. Remove all the
wrappings , staples and straps from the carton. Refer
to the hardware and furniture part list for guidance.
Make sure that you have all the parts before you start
assembling. Place all the wooden furniture parts on a
clean, flat and soft surface, such as a carpet or
rubbermat to prevent scratches.
SCREWDRIVER HAMMER
SELF-PREPARED TOOLS: Tools below are NOT included in package.
1
2
PART LIST
TOP PANEL
MINI FIX
4
SIDE PANEL (L)
6
SIDE PANEL (R)
7
8
QTY
3
5
SHELF PANEL
HARDWARE
A
B
C
D
E
F
G
8 SETS
ALLEN KEY M4 1 PC
BOTTOM PANEL
DRAWER FRONT
BONE PANEL
H
I
J
K
M6 X 5OMM
CSK CAP WOOD SCREW
A1 A2 A3
M8 X 30MM WOOD DOWEL 20 PCS 9
10
11
DRAWER BOTTOM
5/8 NAIL
2 SET
4 PCS
30 PCS
1 PC
1 PC
1 PC
1 PC
M3.5 X 16MM C.B SCREW
M4 X 38MM C.B SCREW 16 PCS
36 PCS
DRAWER SIDE
DRAWER BACK
2 PCS
12
13
14
15
16
2 PCS
3 PCS
1 PC
DOOR PANEL (L)
1 PC
DOOR PANEL (R)
1 PC
BACK PANEL
APRON FRONT
APRON BACK
1 PC
1 PC
APRON BONE 2 PCS
1 PC
1 PC
1 PC
METAL SHELF SUPPORT
5/8 PVC NAIL LEG
SOFT CLOSING 5/8 HINGES
12 PCS
4 PCS
4 PCS
12" DRAWER SLIDE K1 ( L/R )
K2 ( L/R )
13
14
15
16
15
1
2
3
4
5
6
7
8
9
10
11
12
5
6
6
12

CODING
- 372048
MANDO ASSEMBLY GUIDE
/ 42
STEP 6
STEP 4
STEP 2
STEP 5
STEP 3
STEP 1
1
3
4
510
11
12
343
4
5
1
3
4
5
1
2
3
4
5
- Insert hardware A1 onto panel (3) and (4).
(Repeat 4 times.)
- Insert hardware A2 onto panel (1).
(Repeat 4 times.)
- Insert hardware B onto panel (3), (4) and (5).
(Repeat 16 times.)
SCREWDRIVER
REQUIRED
* Ensure the arrows on hardware A1 point towards mounting positions.
PRESS
A1
x4
A2
x4
ROTATE
x16
PRESS
B
5
- Insert hardware A1 onto panel (12).
(Repeat 4 times.)
- Insert hardware A2 onto panel (10) and (11).
(Repeat 4 times.)
- Insert hardware B onto panel (10) and (11).
(Repeat 4 times.)
SCREWDRIVER
REQUIRED
* Ensure the arrows on hardware A1 point towards mounting positions.
PRESS
A1
x4
A2
x4
ROTATE
x4
PRESS
B
12
Fix hardware K1 (L/R) into panel (3) and (4) with hardware E.
(Repeat 3 times for each hardware.)
SCREWDRIVER
REQUIRED
x2
ROTATE
x2 x2
ROTATE ROTATE
K1(L)
EEE
Third hole from the edge.First hole from the edge. Small hole at the center.
K1(R)
Attach panel (3) and (4) to panel (5).
(Repeat 2 times.)
* In this step hardware B are pre-inserted.
5
- Attach panel (1) to panel (3) and (4).
- Insert all hardware A2 into A1.
- Rotate all A1 until tight.
- Apply A3 onto all A1.
(Repeat 4 times.)
OR
HARDWARE
D
SCREWDRIVER
REQUIRED
* In this step hardware A1, A2 and B are pre-inserted.
5
ROTATE
Section View
x4
A2
A1
x4 PRESS
A3
Connect panel (2) to panel (3) and (4)
by using hardware C and D.
(Repeat 4 times.)
ROTATE
x4
C
D
* In this step hardware B are pre-inserted.
HARDWARE
D
5

CODING
- 372048
MANDO ASSEMBLY GUIDE
/ 4
3
STEP 12
STEP 10
STEP 8
STEP 11
STEP 9
STEP 7
10
11
12
1
23
4
5
10
11
12
1
2
3
9
10
11
12
78
1
2
3
4
5
6
7
8
10
11
13
14
15
- Attach panel (10) and (11) to panel (12).
- Insert all hardware A2 into A1.
- Rotate all A1 until tight.
- Apply A3 onto all A1.
(Repeat 4 times.)
OR
HARDWARE
D
SCREWDRIVER
REQUIRED
* In this step hardware A1, A2 and B are pre-inserted.
ROTATE
Section View
x4
A1
A2
x4 PRESS
A3
12
SCREWDRIVER
REQUIRED
ROTATE
F
x8
Assemble panel (10), (11) and (12)
with panel (2) by using hardware F.
(Repeat 8 times.)
5
12
HAMMER
REQUIRED
- Assemble panel (9) to entire body with hardware H.
(Repeat 20 times.)
- Hit hardware I into bottom of panel (10) and (11).
(Repeat 4 times.)
x20
HIT
H
x4
HIT
I
12
Fix hardware J onto panel (7) and (8) by using hardware E.
(Repeat 2 times for each hardware.)
SCREWDRIVER
REQUIRED
x8 ROTATE
JE
- Fix hardware J into panel (3) and (4) by using hardware E.
(Repeat 4 times for each hardware.)
- Tighten or loosen the screw to adjust position of panel (7) and (8).
(Do only when needed.)
SCREWDRIVER
REQUIRED
* In this step hardware J have been assembled in panel (7) and (8).
ADJUST
ADJUST
J
J
ROTATE
x8 E
J
ROTATE
x8 E
J
STEP 1
STEP 3
STEP 4 STEP 2
6
6
Assemble panel (15) to panel (13) and (14)
by using hardware F.
(Repeat 8 times.)
SCREWDRIVER
REQUIRED
ROTATE
F
x8
15

CODING
- 372048
MANDO ASSEMBLY GUIDE
/ 44
13
14
15
16
1
3
4
7
8
13
Assemble panel (16) to entire body with hardware H.
(Repeat 10 times.)
HAMMER
REQUIRED
x10
HIT
H
15
Assemble hardware K2 (L/R) to panel (16) by using hardware E.
(Repeat 3 times for each hardware.)
SCREWDRIVER
REQUIRED
x2
E
x2
E
x2
E
ROTATE ROTATE ROTATE
Hole at the center.
Third hole from the edge. Third hole from the edge.
*Hardware K2 (L/R) shall be leaning against panel (13) when assembling.
K2(L)
K2(R)
13
14
15 16
15
Put all the drawer in place along the drawer slides.
STEP 14
STEP 15
STEP 13