nuhoom MANDO 345044 User manual

1
CODING
- 345044
MANDO ASSEMBLY GUIDE
/ 4
’
Read the instructions carefully. Remove all the
wrappings , staples and straps from the carton. Refer
to the hardware and furniture part list for guidance.
Make sure that you have all the parts before you start
assembling. Place all the wooden furniture parts on a
clean, flat and soft surface, such as a carpet or
rubbermat to prevent scratches.
SCREWDRIVER HAMMER
SELF-PREPARED TOOLS: Tools below are NOT included in package.
1
2
PART LIST
TOP PANEL
MINI FIX
4
SIDE PANEL (L)
6
SIDE PANEL (R)
7
8
QTY
3
5
BONE PANEL
HARDWARE
A
B
C
D
E
F
G
10 SETS
ALLEN KEY M4 1 PC
BOTTOM PANEL
DRAWER FRONT
CENTER PANEL
H
I
J
K
M6 X 5OMM
CSK CAP WOOD SCREW
A1 A2 A3
M8 X 30MM WOOD DOWEL 32 PCS 9
10
11 APRON BONE (BACK)
DRAWER BOTTOM
14" DRAWER SLIDE K1 ( L/R )
K2 ( L/R )
5/8 NAIL
2 SETS
6 PCS
52 PCS
1 PC
1 PC
1 PC
1 PC
1 PC
2 PCS
2 PCS
M3.5 X 16MM C.B SCREW
M4 X 38MM C.B SCREW
M4 X 30MM C.B SCREW
28 PCS
2 PCS
71 PCS
DRAWER SIDE
DRAWER BACK
4 PCS
2 PCS
12
13
14
15
16
17
4 PCS
DOOR PANEL (L)
DOOR PANEL (R)
2 PCS
2 PCS
BACK PANEL 1 PC
APRON BONE (FRONT) 1 PC
1 PC
APRON BONE 2 PCS
CENTER LEG 1 PC
5/8 PVC NAIL LEG 5 PCS
8 PCS
SOFT CLOSING 5/8 HINGES
1
2
3
4
5
6
7
8
9
10
11
12
13
66
6
7
8
12
14
15
16
17
16
14
15
16
17
16

CODING
- 345044
MANDO ASSEMBLY GUIDE
/ 42
STEP 6
STEP 4
STEP 2
STEP 5
STEP 3
STEP 1
1
3
4
5
6
11
12
34
5
5
3
4
5
6
1
3
4
5
6
- Insert hardware A1 onto panel (3), (4) and (5).
(Repeat 6 times.)
- Insert hardware A2 onto panel (1).
(Repeat 6 times.)
- Insert hardware B onto panel (3), (4) and (5).
(Repeat 12 times.)
SCREWDRIVER
REQUIRED
* Ensure the arrows on hardware A1 point towards mounting positions.
A2
x6
ROTATE
PRESS
A1
x6
x12
PRESS
B
- Insert hardware A1 onto panel (12).
(Repeat 4 times.)
- Insert hardware A2 onto panel (10) and (11).
(Repeat 4 times.)
- Insert hardware B onto panel (6), (10) and (11).
(Repeat 20 times.)
SCREWDRIVER
REQUIRED
* Ensure the arrows on hardware A1 point towards mounting positions.
10
x20
PRESS
B
6
6
6
A2
x4
ROTATE
12
PRESS
A1
x4
Fix hardware K1 (L/R) into panel (3), (4) and (5) with hardware E.
(Repeat 3 times for each hardware.)
SCREWDRIVER
REQUIRED
x3
ROTATE
x3 x3
ROTATE ROTATE
K1(L)
EEE
Third hole from the edge.First hole from the edge. Small hole at the center.
K1(R)
K1(L)
Fix hardware K1 (R) into panel (5) with hardware E.
(Repeat 2 times for each hardware.)
SCREWDRIVER
REQUIRED
K1(R)
Third hole from the edge. First hole from the edge.
x1x1
ROTATE
ROTATE
EE
Attach panel (6) to panel (3), (4) and (5) .
(Repeat 4 times.)
* In this step hardware B are pre-inserted.
6
6
6
- Attach panel (1) to panel (3), (4) and (5).
- Insert all hardware A2 into A1.
- Rotate all A1 until tight.
- Apply A3 onto all A1.
(Repeat 6 times.)
OR
HARDWARE
D
SCREWDRIVER
REQUIRED
* In this step hardware A1, A2 and B are pre-inserted.
ROTATE
Section View
x6
A1
A2
x6 PRESS
A3
6
6
6

CODING
- 345044
MANDO ASSEMBLY GUIDE
/ 4
3
STEP 12
STEP 10
STEP 8
STEP 11
STEP 9
STEP 7
1
2
3
4
5
6
10
11
12
10
11
12
13
1
2
3
4
5
6
10
11
12
13
1
2
3
9
10
11
13
7
8
Connect panel (2) to panel (3), (4) and (5)
by using hardware C and D.
(Repeat 6 times.)
ROTATE
x6
C
D
* In this step hardware B are pre-inserted.
HARDWARE
D
6
6
6
- Attach panel (10) and (11) to panel (12).
- Insert all hardware A2 into A1.
- Rotate all A1 until tight.
- Apply A3 onto all A1.
(Repeat 4 times.)
OR
HARDWARE
D
SCREWDRIVER
REQUIRED
* In this step hardware A1, A2 and B are pre-inserted.
ROTATE
Section View
x4
A2
A1
x4 PRESS
A3
12
SCREWDRIVER
REQUIRED
Assemble panel (13) with panel (11) by using hardware F.
(Repeat 2 times.)
ROTATE
F
x2 12
SCREWDRIVER
REQUIRED
Assemble panel (2) with panel (10), (11) and (12)
by using hardware G.
(Repeat 12 times.)
ROTATE
G
x12
HAMMER
REQUIRED
- Assemble panel (9) to entire body with hardware H.
(Repeat 28 times.)
- Hit hardware J into bottom of panel (10), (11) and (13).
(Repeat 5 times.)
x28
HIT
H
x5
HIT
J
Fix hardware J onto panel (7) and (8) by using hardware E.
(Repeat 2 times for each hardware.)
SCREWDRIVER
REQUIRED
7
8
6
12
x16 ROTATE
JE

CODING
- 345044
MANDO ASSEMBLY GUIDE
/ 44
STEP 16
STEP 14
STEP 17
STEP 15
STEP 13
1
2
3
4
5
6
7
8
10
11
14
16
14
15
16 17
14
15
16 17
1
4
78
14
- Fix hardware J into panel (3), (4) and (5) by using hardware E.
(Repeat 4 times for each hardware.)
- Tighten or loosen the screw to adjust position of panel (7) and (8).
(Do only when needed.)
SCREWDRIVER
REQUIRED
* In this step hardware J have been assembled in panel (7) and (8).
6
7
8
Assemble panel (16) to panel (14) and (15)
by using hardware G.
(Repeat 16 times.)
SCREWDRIVER
REQUIRED
x16
G
ROTATE
16
15
14
16
16
15
Assemble panel (17) to entire body with hardware H.
(Repeat 24 times.)
HAMMER
REQUIRED
x24
HIT
H
16
14
15
16 17
16
Assemble hardware K2 (L/R) to panel (17) by using hardware E.
(Repeat 3 times for each hardware.)
SCREWDRIVER
REQUIRED
x4
E
x4
E
x4
E
ROTATE ROTATE ROTATE
Hole at the center.
Third hole from the edge. Third hole from the edge.
*Hardware K2 (L/R) shall be leaning against panel (14) when assembling.
K2(R)
K2(L)
16
14
15
16 17
16
K2(L)
K2(R)
Put all the drawer in place along the drawer slides.
7
8
14
ADJUST ADJUST
JJ
ROTATE
x16
E
J
ROTATE
x16
E
J
STEP 1
STEP 3 STEP 4
STEP 2