nuhoom RHODES 523039 User manual

1
CODING
- 523039
RHODES ASSEMBLY GUIDE
/ 3
’
Read the instructions carefully. Remove all the
wrappings , staples and straps from the carton. Refer
to the hardware and furniture part list for guidance.
Make sure that you have all the parts before you start
assembling. Place all the wooden furniture parts on a
clean, flat and soft surface, such as a carpet or
rubbermat to prevent scratches.
1
2
PART LIST
4
QTY
3
HARDWARE
A
B
C
D
E
1 PC
1 PC
1 PC
1 PC
MINI FIX
M8 X 30MM WOOD DOWEL
1 PC
A1 A2 A3
1
2
3
4
5
6
7
8
9
9
9
TOP PANEL
SIDE PANEL (L)
6
SIDE PANEL (R)
7
8
5
BOTTOM PANEL
9
FRONT RAIL TOP
BACK PANEL
FRONT RAIL BOTTOM
SHELF PANEL
MIDDLE PANEL
3 PCS
1 PC
1 PC
1 PC
1 PC
FMETAL SHELF SUPPORT
15 SETS
22 PCS
30 PCS
12 PCS
4 PCS
ALLEN KEY M4
5/8 PVC NAIL LEG
5/8 NAIL
SCREWDRIVER HAMMER
SELF-PREPARED TOOLS: Tools below are NOT included in package.

CODING
- 523039
RHODES ASSEMBLY GUIDE
/ 32
2
7
2
3
4
5
6
7
1
23
4
5
6
7
- Insert hardware A1 onto panel (2).
(Repeat 7 times.)
- Insert hardware A2 onto panel (1) and (7).
(Repeat 7 times.)
- Insert hardware B onto panel (2), (6) and (7).
(Repeat 14 times.)
SCREWDRIVER
REQUIRED
* Ensure the arrows on hardware A1 point towards mounting positions.
PRESS
A1
x7
x14
PRESS
B
A2
x7
ROTATE
- Insert hardware A1 onto panel (3), (4) and (5).
(Repeat 8 times.)
- Insert hardware A2 onto panel (3) and (4).
(Repeat 8 times.)
- Insert hardware B onto panel (3), (4) and (5).
(Repeat 8 times.)
SCREWDRIVER
REQUIRED
* Ensure the arrows on hardware A1 point towards mounting positions.
PRESS
A1
x8
x8
PRESS
B
A2
x8
ROTATE
- Attach panel (7) to panel (2).
- Insert all hardware A2 into A1.
- Rotate all A1 until tight.
- Apply A3 onto all A1.
(Repeat 3 times.)
OR
HARDWARE
D
SCREWDRIVER
REQUIRED
* In this step hardware A1, A2 and B are pre-inserted.
- Attach panel (3) and (4) to panel (2), (5), (6) and (7).
- Insert all hardware A2 into A1.
- Rotate all A1 until tight.
- Apply A3 onto all A1.
(Repeat 8 times.)
OR
HARDWARE
D
SCREWDRIVER
REQUIRED
* In this step hardware A1, A2 and B are pre-inserted.
ROTATE x3
A2
A1
PRESS x3
A3
ROTATE
Section View
x8
A2 A1
x8
PRESS
A3
STEP 4
STEP 2
STEP 3
STEP 1

CODING
- 523039
RHODES ASSEMBLY GUIDE
/ 3
3
1
2
3
4
5
8
9
1
2
3
4
5
61
2
3
4
8
- Attach panel (1) to panel (3), (4) and (6).
- Insert all hardware A2 into A1.
- Rotate all A1 until tight.
- Apply A3 onto all A1.
(Repeat 4 times.)
OR
HARDWARE
D
SCREWDRIVER
REQUIRED
* In this step hardware A1, A2 and B are pre-inserted.
ROTATE
Section View
x4
A2
A1
x4 PRESS
A3
- Assemble panel (8) to entire body with hardware C.
(Repeat 30 times.)
- Hit hardware E into bottom of panel (3) and (4).
(Repeat 4 times.)
x4
HIT
E
HAMMER
REQUIRED
x12 PRESS
- Insert hardware F into mounting positions
on panel (3) and (4) by hand.
(Repeat 12 times.)
F
- Assemble panel (9) into between panel (3) and (4).
(Repeat 3 times.)
*In this step hardware F are pre-inserted.
*Hardware F can fix to another up and down hole
on panel (3) and (4) for adjust panel (9) to high or lower.
9
9
1
2
3
4
5
8
x30 HIT
C
STEP 8
STEP 6
STEP 7
STEP 5