nuhoom CAPRI 372050 User manual

1
CODING
- 372050
CAPRI ASSEMBLY GUIDE
/ 4
’
Read the instructions carefully. Remove all the
wrappings , staples and straps from the carton. Refer
to the hardware and furniture part list for guidance.
Make sure that you have all the parts before you start
assembling. Place all the wooden furniture parts on a
clean, flat and soft surface, such as a carpet or
rubbermat to prevent scratches.
SCREWDRIVER HAMMER
SELF-PREPARED TOOLS: Tools below are NOT included in package.
PART LIST
MINI FIX
QTY
HARDWARE
A
B
C
D
E
F
G
8 SETS
ALLEN KEY M4 1 PC
H
I
J
M6 X 5OMM
CSK CAP WOOD SCREW
A1 A2 A3
M8 X 30MM WOOD DOWEL 12 PCS
14" DRAWER SLIDE N1 ( L/R )
N2 ( L/R )
5/8 NAIL
4 PCS
4 PCS
8 PCS
4 PCS
36 PCS
36 PCS
M3.5 X 16MM C.B SCREW
M4 X 38MM C.B SCREW
METAL SHELF SUPPORT
1
2
TOP PANEL
4
SIDE PANEL (L)
6
SIDE PANEL (R)
7
8
3
5MIDDLE PANEL
BOTTOM PANEL
DRAWER FRONT
DRAWER SIDE
9
10
11
DRAWER BOTTOM
DRAWER BACK
1 PC
1 PC
1 PC
1 PC
1 PC
1 PC
2 PCS
12
13
14 2 PCS
BACK PANEL
DOOR PANEL (L)
DOOR PANEL (R)
SHELF PANEL
15 4 PCS
METAL SIDE
METAL SUPPORT
1 PC
1 PC
1 PC
1 PC
1 PC
2 PCS
K8 PCS
L4 PCS
M2 PCS
N
8 PCS
M3 X 12MM C.B SCREW
JCBC SCREW M6 X 30MM
JCBC SCREW M6 X 40MM
SOFT CLOSING 5/8 HINGES
1 SET
HANDLE 4020 L BAR 100MM
1
2
3
4
5
6
6
7
8
9
14
14
15
15
M
10
11
11
12
13
M

CODING
- 372050
CAPRI ASSEMBLY GUIDE
/ 42
STEP 6
STEP 4
STEP 2
STEP 5
STEP 3
STEP 1
- Insert hardware A1 onto panel (3), (4) and (5).
(Repeat 8 times.)
- Insert hardware A2 onto panel (1), (3) and (4).
(Repeat 8 times.)
- Insert hardware B onto panel (3), (4) and (5).
(Repeat 12 times.)
SCREWDRIVER
REQUIRED
* Ensure the arrows on hardware A1 point towards mounting positions.
x12
PRESS
B
PRESS
A1
x8
A2
x8
ROTATE
- Attach panel (3) and (4) to panel (5).
- Insert all hardware A2 into A1.
- Rotate all A1 until tight.
- Apply A3 onto all A1.
(Repeat 4 times.)
OR
SCREWDRIVER
REQUIRED
* In this step hardware A1, A2 and B are pre-inserted.
HARDWARE
D
ROTATE
Section View
x4
A2 A1
x4
PRESS
A3
- Attach panel (1) to panel (3) and (4).
- Insert all hardware A2 into A1.
- Rotate all A1 until tight.
- Apply A3 onto all A1.
(Repeat 4 times.)
OR
SCREWDRIVER
REQUIRED
* In this step hardware A1, A2 and B are pre-inserted.
HARDWARE
D
ROTATE
Section View
x4
A2
A1
x4 PRESS
A3
Fix hardware N1 (L) into panel (3) with hardware H.
(Repeat 3 times for each hardware.)
SCREWDRIVER
REQUIRED
N1(L)
Fix hardware N1 (R) into panel (4) with hardware H.
(Repeat 3 times for each hardware.)
N1(R)
SCREWDRIVER
REQUIRED
x1
ROTATE
x1 x1
ROTATE ROTATE
HHH
Third hole from the edge.First hole from the edge. Small hole at the center.
Third hole from the edge. First hole from the edge.
Small hole at the center.
x1x1x1
ROTATE
ROTATE
ROTATE
HHH
Connect panel (2) to panel (3) and (4) by using
hardware C and D.
(Repeat 4 times.)
ROTATE
x4
C
D
* In this step hardware B are pre-inserted.
HARDWARE
D
1
11
2
3
3
3
3
3
4
4
4
4
4
5
5
5
5

CODING
- 372050
CAPRI ASSEMBLY GUIDE
/ 4
3
STEP 12
STEP 10
STEP 8
STEP 11
STEP 9
STEP 7 HAMMER
REQUIRED
Assemble panel (7) to entire body with hardware J.
(Repeat 24 times.)
x24
HIT
J
Connect Metal Side (14) to Metal Support (15)
by using hardware D and F.
(Repeat 8 times.)
HARDWARE
D
ROTATE
x8
F
D
Connect Metal Side (14) to panel (2) by using
hardware D and E.
(Repeat 4 times.)
HARDWARE
D
ROTATE
x4
E
D
x8 PRESS
- Insert hardware K into mounting positions on panel (3) and (4) by hand.
(Repeat 8 times.)
- Assemble the panel (6) into between panel (3) and (4).
(Repeat 2 times.)
K
Fix hardware L onto panel (8) and (9) by using hardware H.
(Repeat 2 times for each hardware.)
Fix hardware M onto panel (8) and (10) by using hardware G.
(Repeat 2 times for each hardware.)
SCREWDRIVER
REQUIRED
ROTATE
x8
H
L
ROTATE
x4
G
- Fix hardware L into panel (3) and (4) by using hardware H.
(Repeat 4 times for each hardware.)
- Tighten or loosen the screw to adjust position of panel (8) and (9).
(Do only when needed.)
SCREWDRIVER
REQUIRED
* In this step hardware L have been assembled in panel (8) and (9).
ADJUST
ADJUST
L
L
ROTATE
x8 H
L
ROTATE
x8 H
L
STEP 1
STEP 3
STEP 4 STEP 2
1
1
2
2
2
2
3
3
3
3
4
4
5
5
6
6
6
6
7
7
88
9
9
10
14
14
14
14
14
14
14
14
15
15
15
15
15
15
15
15
M
M
M

CODING
- 372050
CAPRI ASSEMBLY GUIDE
/ 44
Assemble panel (11) with panel (10) and (12) by using
hardware I.
(Repeat 8 times.)
SCREWDRIVER
REQUIRED
x8
I
ROTATE
Assemble panel (13) to entire body with hardware J.
(Repeat 12 times.)
HAMMER
REQUIRED
x12
HIT
J
Assemble hardware N2 (L/R) to panel (13) by using hardware H.
(Repeat 3 times for each hardware.)
N2 (R)
Hole at the center.
Third hole from the edge.
Third hole from the edge.
x2
H
x2
H
x2
H
ROTATE
ROTATE
ROTATE
*Hardware N2 (L/R) shall be leaning against panel (10) when assembling.
SCREWDRIVER
REQUIRED
N2 (L)
Put all the drawer in place along the drawer slides.
1
4
89
10
10
10
10
11
11
11
11
11
11
12
12
12
13
13
14
14
15
15
M
M
M
STEP 16
STEP 14
STEP 15
STEP 13