nuhoom VOLOS 133082 User manual

1
CODING
- 133082
VOLOS ASSEMBLY GUIDE
/ 4
’
Read the instructions carefully. Remove all the
wrappings , staples and straps from the carton. Refer
to the hardware and furniture part list for guidance.
Make sure that you have all the parts before you start
assembling. Place all the wooden furniture parts on a
clean, flat and soft surface, such as a carpet or
rubbermat to prevent scratches.
SCREWDRIVER HAMMER
SELF-PREPARED TOOLS: Tools below are NOT included in package.
PART LIST
MINI FIX
QTY
HARDWARE
A
B
C
D
E
F
G
12 SETS
ALLEN KEY M4 1 PC
H
I
J
M6 X 5OMM
CSK CAP WOOD SCREW
A1 A2 A3
M8 X 30MM WOOD DOWEL 18 PCS
5/8 NAIL
4 SETS
10 PCS
8 PCS
68 PCS
32 PCS
32 PCS
4 PCS
M3.5 X 16MM C.B SCREW
M4 X 38MM C.B SCREW
1
2
TOP PANEL
4
SIDE PANEL
6
7
8
3
5MIDDLE PANEL
BOTTOM PANEL
DRAWER FRONT
CENTER PANEL
DRAWER SIDE
9DRAWER BOTTOM
DRAWER BACK
1 PC
1 PC
1 PC
8 PCS
4 PCS
4 PCS
4 PCS
2 PCS
2 PCS
M3 X 12MM C.B SCREW
HANDLE EM 0071
10'' DRAWER SLIDE J1 ( L/R )
J2 ( L/R )
K
L
METAL LEG 90 x 90 x 10 x H145MM 4 PCS
1 PC
METAL LEG 50 x 50 x H140MM
(CENTER)
1
2
3
3
4
4
5
K
K
L
6 7
7
8
9
I
6 7
7
8
9
I
67
7
8
9
I
6 7
7
8
9
I

CODING
- 133082
VOLOS ASSEMBLY GUIDE
/ 42
STEP 6
STEP 4
STEP 2
STEP 5
STEP 3
STEP 1
- Insert hardware A1 onto panel (5).
(Repeat 4 times.)
- Insert hardware A2 onto panel (1).
(Repeat 10 times.)
- Insert hardware B onto panel (5).
(Repeat 2 times.)
SCREWDRIVER
REQUIRED
* Ensure the arrows on hardware A1 point towards mounting positions.
- Insert hardware A1 onto panel (3).
(Repeat 4 times.)
- Insert hardware A2 onto panel (3).
(Repeat 2 times.)
- Insert hardware B onto panel (3).
(Repeat 8 times.)
SCREWDRIVER
REQUIRED
* Ensure the arrows on hardware A1 point towards mounting positions.
- Insert hardware A1 onto panel (4).
(Repeat 4 times.)
- Insert hardware B onto panel (4).
(Repeat 8 times.)
SCREWDRIVER
REQUIRED
* Ensure the arrows on hardware A1 point towards mounting positions.
A2
x10
ROTATE
x2
PRESS
B
PRESS
A1
x4
PRESS
A1
x4
A2
x2
ROTATE x8
PRESS
B
PRESS
A1
x4
x8
PRESS
BFix hardware J1 (L/R) into panel (3) with hardware F.
(Repeat 3 times for each hardware.)
SCREWDRIVER
REQUIRED
x4
ROTATE
x4 x4
ROTATE ROTATE
J1(L)
FFF
Second hole from the edge.
First hole from the edge. Small hole at the center.
Fix hardware J1 (L) into panel (4) with hardware F.
(Repeat 3 times for each hardware.)
SCREWDRIVER
REQUIRED
x2
ROTATE
x2 x2
ROTATE ROTATE
FFF
Second hole from the edge.
First hole from the edge. Small hole at the center.
J1(R)
J1(L) J1(R)
x2x2x2
ROTATE
ROTATE
ROTATE
Fix hardware J1 (R) into panel (4) with hardware F.
(Repeat 3 times for each hardware.)
SCREWDRIVER
REQUIRED
Last hole from the edge. Second hole from the edge.Big hole at the center.
FFF
J1(L) J1(R)
1
33
4
4
44
4
4
5
3J1(L)
J1(R)
3

CODING
- 133082
VOLOS ASSEMBLY GUIDE
/ 4
3
STEP 12
STEP 10
STEP 8
STEP 11
STEP 9
STEP 7
- Attach panel (3) to panel (5).
- Insert all hardware A2 into A1.
- Rotate all A1 until tight.
- Apply A3 onto all A1.
(Repeat 2 times.)
OR
HARDWARE
D
SCREWDRIVER
REQUIRED
* In this step hardware A1, A2 and B are pre-inserted.
- Attach panel (1) to panel (3), (4) and (5).
- Insert all hardware A2 into A1.
- Rotate all A1 until tight.
- Apply A3 onto all A1.
(Repeat 10 times.)
OR
HARDWARE
D
SCREWDRIVER
REQUIRED
* In this step hardware A1, A2 and B are pre-inserted.
ROTATE
Section View
x2
A2 A1
x2
PRESS
A3
ROTATE
Section View
x10
A1
A2
x10 PRESS
A3
Connect panel (2) to panel (3), (4) and (5) by using
hardware C and D.
(Repeat 10 times.)
ROTATE
x10
C
D
* In this step hardware B are pre-inserted.
HARDWARE
DAssemble hardware K and L onto panel (2) by using hardware F.
(Repeat 4 times for each hardware.)
SCREWDRIVER
REQUIRED
x4
FL
ROTATE
ROTATE
x16
FK
L
Fix hardware I onto panel (6) by using hardware E.
(Repeat 8 times.)
* In this step only show one of the drawers.
SCREWDRIVER
REQUIRED Assemble panel (7) to panel (6) and (8) by using hardware G.
(Repeat 32 times.)
* In this step only show one of the drawers.
SCREWDRIVER
REQUIRED
ROTATE
E
x8 x32
G
ROTATE
1
11
22
3
3
3
3
3
3
3
3
4
4
44
5
5
5
6
6
7
7
8
I
K
K
K
L

CODING
- 133082
VOLOS ASSEMBLY GUIDE
/ 44
Assemble panel (9) to entire body with hardware H.
(Repeat 32 times.)
* In this step only show one of the drawers.
HAMMER
REQUIRED Assemble hardware J2 (L/R) to panel (9) by using hardware F.
(Repeat 3 times for each hardware.)
* In this step only show one of the drawers.
Hole at the center.
Third hole from the edge.
Third hole from the edge.
x8
F
x8
F
x8
F
ROTATE
ROTATE
ROTATE
*Hardware J2 (L/R) shall be leaning against panel (6) when assembling.
SCREWDRIVER
REQUIRED
J2(R)
Put all the drawer in place along the drawer slides.
x32
HIT
H
J2(L)
1
3
3
4
6
6
7
7
7
7
8
8
9
9
6
6
6
STEP 14
STEP 15
STEP 13