nuhoom VOLOS 336046 User manual

1
CODING
- 336046
VOLOS ASSEMBLY GUIDE
/ 3
’
Read the instructions carefully. Remove all the
wrappings , staples and straps from the carton. Refer
to the hardware and furniture part list for guidance.
Make sure that you have all the parts before you start
assembling. Place all the wooden furniture parts on a
clean, flat and soft surface, such as a carpet or
rubbermat to prevent scratches.
SCREWDRIVER HAMMER
SELF-PREPARED TOOLS: Tools below are NOT included in package.
PART LIST
MINI FIX
QTY
HARDWARE
A
B
C
D
E
F
G
8 SETS
ALLEN KEY M4 1 PC
H
I
K
M6 X 5OMM
CSK CAP WOOD SCREW
A1 A2 A3
M8 X 30MM WOOD DOWEL 16 PCS
5/8 NAIL
8 PCS
4 PCS
58 PCS
4 PCS
30 PCS
2 PCS
M3.5 X 16MM C.B SCREW
METAL SHELF SUPPORT
1
2
TOP PANEL
4
SIDE PANEL (L)
6
SIDE PANEL (R)
7
8
3
5
SHELF PANEL
BOTTOM PANEL
CENTER PANEL (L)
9
10
1 PC
1 PC
1 PC
1 PC
1 PC
1 PC
CENTER PANEL (R)
BACK PANEL
DOOR PANEL (L)
DOOR PANEL (R)
1 PC
1 PC
1 PC
1 PC
M3 X 12MM C.B SCREW
STOPPER(2 PIN)
SOFT CLOSING 7/8 HINGES
10" AIR PRESS PULL ROD
L
L1 L2 L3
2 SETS
JHANDLE EM 0071 2 PCS
4 PCS
M
N
METAL LEG 90 x 90 x 10 x H145MM 4 PCS
METAL LEG 50 x 50 x H140MM
(CENTER) 2 PCS
1
2
3
4
5
6
78
9
10
J
J
M
M
N
N

CODING
- 336046
VOLOS ASSEMBLY GUIDE
/ 32
STEP 6
STEP 4
STEP 2
STEP 5
STEP 3
STEP 1
x8
PRESS
B
PRESS
A1
x4
ROTATE
F
L2
x6
- Attach panel (1) to panel (3), (4), (5) and (6).
- Insert all hardware A2 into A1.
- Rotate all A1 until tight.
- Apply A3 onto all A1.
(Repeat 8 times.)
OR
HARDWARE
D
SCREWDRIVER
REQUIRED
* In this step hardware A1, A2 and B are pre-inserted.
ROTATE
Section View
x8
A2
A1
x8 PRESS
A3
- Connect panel (2) to panel (3), (4), (5) and (6) by using
hardware C and D.
(Repeat 8 times.)
ROTATE
x8
C
D
* In this step hardware B are pre-inserted.
HARDWARE
D
HAMMER
REQUIRED
- Assemble panel (8) to entire body with hardware H.
(Repeat 30 times.)
x30
HIT
H
- Assemble hardware M and N onto panel (2) by using
hardware F.
(Repeat 4 times for each hardware.)
SCREWDRIVER
REQUIRED
x8
ROTATE
x16
FM
F
N
ROTATE
N
- Insert hardware A1 onto panel (5) and (6).
(Repeat 4 times.)
- Insert hardware A2 onto panel (1).
(Repeat 8 times.)
- Insert hardware B onto panel (5) and (6).
(Repeat 8 times.)
- Hit hardware I onto panel (1).
(Repeat 2 times.)
SCREWDRIVER
REQUIRED
* Ensure the arrows on hardware A1 point towards mounting positions.
- Assemble hardware L2 onto panel (3) and (4) by using
hardware F.
(Repeat 3 times for each hardware.)
- Insert hardware A1 onto panel (3) and (4).
(Repeat 4 times.)
- Insert hardware B onto panel (3) and (4).
(Repeat 8 times.)
SCREWDRIVER
REQUIRED
* Ensure the arrows on hardware A1 point towards mounting positions.
HAMMER
REQUIRED
HIT
x2
I
PRESS
A1
x4
x8
PRESS
B
A2
x8
ROTATE
1
11
2
2
2
3
3
33
4
4
4
5
5
5
6
6
6
8
8
M
M
M
N
3
N

CODING
- 336046
VOLOS ASSEMBLY GUIDE
/ 3
3
STEP 12
STEP 10
STEP 8
STEP 11
STEP 9
STEP 7
- Fix hardware K onto panel (9) and (10) by using hardware F.
(Repeat 2 times for each hardware.)
- Assemble hardware L3 onto panel (9) and (10) by using hardware F.
(Repeat 2 times for each hardware.)
SCREWDRIVER
REQUIRED
ROTATE
x8
K
F
ROTATE
F
L3
x4
SCREWDRIVER
REQUIRED
- Fix hardware J onto panel (9) and (10) by using hardware E.
(Repeat 2 times for each hardware.)
ROTATE
E
x4
- Fix hardware K into panel (2) by using hardware F.
(Repeat 4 times for each hardware.)
- Tighten or loosen the screw to adjust position of panel (9) and (10).
(Do only when needed.)
SCREWDRIVER
REQUIRED
* In this step hardware K have been assembled in panel (9) and (10).
K
F
x8
ADJUST
K
K
ADJUST
ROTATE
STEP 3
STEP 4
K
F
x8
ROTATE
STEP 1
STEP 2
- Fix hardware L1 to L2 and L3 by hand.
(Repeat 2 times.)
* In this step hardware L2 and L3 have been assembled.
PRESS
L2 L1
PRESS
L3
L1
x2
x2
x4 PRESS
- Insert hardware G into mounting positions on panel (5) and (6) by hand.
(Repeat 4 times.)
G
- Assemble panel (7) into between panel (5) and (6).
(Repeat 1 times.)
* In this step hardware G are pre-inserted.
1
1
1
1
2
2
22
3
3
3
3
4
4
4
4
5
5
55
6
6
66
7
77
8
8
9
9
99
10
10
10
JJ
10