nuhoom CAPRI 343038 User manual

1
CODING
- 343038
CAPRI ASSEMBLY GUIDE
/ 5
’
Read the instructions carefully. Remove all the
wrappings , staples and straps from the carton. Refer
to the hardware and furniture part list for guidance.
Make sure that you have all the parts before you start
assembling. Place all the wooden furniture parts on a
clean, flat and soft surface, such as a carpet or
rubbermat to prevent scratches.
SCREWDRIVER HAMMER
SELF-PREPARED TOOLS: Tools below are NOT included in package.
1
2
PART LIST
TOP PANEL
MINI FIX
4
SIDE PANEL (L)
6
SIDE PANEL (R)
7
8
QTY
3
5
SHELF PANEL
HARDWARE
A
B
C
D
E
F
G
10 SETS
ALLEN KEY M4 1 PC
BOTTOM PANEL
DRAWER FRONT (UP)
CENTER PANEL
H
I
J
K
M6 X 5OMM
CSK CAP WOOD SCREW
A1 A2 A3
M8 X 30MM WOOD DOWEL 12 PCS 9
10
11
DRAWER BOTTOM
14" DRAWER SLIDE N1 ( L/R )
N2 ( L/R )
5/8 NAIL
3 SETS
6 PCS
60 PCS
1 PC
1 PC
1 PC
1 PC
1 PC
1 PC
2 PCS
4 PCS
M3.5 X 16MM C.B SCREW
M4 X 38MM C.B SCREW
M3 X 12MM C.B SCREW
24 PCS
4 PCS
48 PCS DRAWER SIDE
DRAWER BACK
12
13
14
15
16
DRAWER FRONT (DOWN)
1 PC
MIDDLE BONE 1 PC
BACK PANEL 1 PC
DOOR PANEL 1 PC
6 PCS
3 PCS
3 PCS
METAL SIDE
METAL SUPPORT
2 PCS
METAL SHELF SUPPORT 4 PCS
MODERN HANDLE L100 2 PCS
L
M
N
JCBC SCREW M6 X 30MM
JCBC SCREW M6 X 40MM
6 PCS
8 PCS
2 PCS
SOFT CLOSING 5/8 HINGES 1
2
3
4
5
6
7
8
9
15 16
15
16
16
16
10
12
12
13
14
11
12
12
13
14
J
11
12
12
13
14
J

CODING
- 343038
CAPRI ASSEMBLY GUIDE
/ 52
STEP 6
STEP 4
STEP 2
STEP 5
STEP 3
STEP 1
1
7
34
5
35
3
57
2
3
4
571
2
3
4
57
- Insert hardware A1 onto panel (7).
(Repeat 4 times.)
- Insert hardware A2 onto panel (1).
(Repeat 6 times.)
SCREWDRIVER
REQUIRED
* Ensure the arrows on hardware A1 point towards mounting positions.
A2
x6
ROTATE
PRESS
A1
x4
- Insert hardware A1 onto panel (3), (4) and (5).
(Repeat 6 times.)
- Insert hardware A2 onto panel (3) and (5).
(Repeat 4 times.)
- Insert hardware B onto panel (3), (4) and (5).
(Repeat 12 times.)
* Ensure the arrows on hardware A1 point towards mounting positions.
PRESS
A1
x6
x12
PRESS
B
Fix hardware N1 (L/R) into panel (3) and (5) with hardware E.
(Repeat 3 times for each hardware.)
SCREWDRIVER
REQUIRED
x6
ROTATE
x6 x6
ROTATE ROTATE
N1(L)
EEE
Third hole from the edge.First hole from the edge. Small hole at the center.
N1(R)
- Attach panel (3) and (5) to panel (7).
- Insert all hardware A2 into A1.
- Rotate all A1 until tight.
- Apply A3 onto all A1.
(Repeat 4 times.)
OR
HARDWARE
D
SCREWDRIVER
REQUIRED
* In this step hardware A1, A2 and B are pre-inserted.
- Attach panel (1) to panel (3), (4) and (5).
- Insert all hardware A2 into A1.
- Rotate all A1 until tight.
- Apply A3 onto all A1.
(Repeat 6 times.)
OR
HARDWARE
D
SCREWDRIVER
REQUIRED
* In this step hardware A1, A2 and B are pre-inserted.
Section View
ROTATE A1
x4
A2
x4 PRESS
A3
Connect panel (2) to panel (3), (4) and (5)
by using hardware C and D.
(Repeat 6 times.)
ROTATE
x6
C
D
* In this step hardware B are pre-inserted.
HARDWARE
D
ROTATE
Section View
x6
A2
A1
x6 PRESS
A3
5
A2
x4
ROTATE

CODING
- 343038
CAPRI ASSEMBLY GUIDE
/ 5
3
STEP 12
STEP 10
STEP 8
STEP 11
STEP 9
STEP 7
1
2
3
8
15
16
1
2
3
8
15
16
1
2
34
5
7
8
15
1
2
3
4
5
6
7
8
15 16
9
HAMMER
REQUIRED
Assemble panel (8) to entire body with hardware H.
(Repeat 30 times.)
x30
HIT
H
Connect Metal Side (15) to Metal Support (16)
by using hardware D and L.
(Repeat 8 times.)
HARDWARE
D
ROTATE
x8
D
L
15
16
16
16
Connect Metal Frame (15) to panel (2)
by using hardware D and K.
(Repeat 6 times.)
ROTATE
x6
K
D
HARDWARE
D
16
16
15
x4 PRESS
Insert hardware I into mounting positions on panel (4) and (5) by hand.
(Repeat 4 times.)
I
16
16
15
Assemble panel (6) into between panel (4) and (5).
(Repeat 1 times.)
* In this step hardware I are pre-inserted.
15
16
Fix hardware M onto panel (9) by using hardware E.
(Repeat 2 times for each hardware.)
SCREWDRIVER
REQUIRED
x4
ROTATE
M
E

CODING
- 343038
CAPRI ASSEMBLY GUIDE
/ 54
1
2
3
4
5
6
8
9
15
16
11
10 11
12
13
10
12
- Fix hardware M into panel (4) by using hardware E.
(Repeat 2 times for each hardware.)
- Tighten or loosen the screw to adjust position of panel (9).
(Do only when needed.)
SCREWDRIVER
REQUIRED
* In this step hardware M have been assembled in panel (9).
15
Fix hardware J onto panel (11) by using hardware F.
(Repeat 4 times .)
SCREWDRIVER
REQUIRED
ROTATE
x4
F
11
J
J
Assemble panel (12) to panel (10) or (11) and (13)
by using hardware G.
(Repeat 12 times.)
x12
G
ROTATE
SCREWDRIVER
REQUIRED
12
13
13
11
J
Assemble panel (12) to panel (10) or (11) and (13)
by using hardware G.
(Repeat 12 times.)
SCREWDRIVER
REQUIRED
ROTATE
G
x12
12
11
12
13
12
12
13
12
12
13
11
J
ADJUST
ADJUST
M
M
ROTATE
x4
E
M
ROTATE
x4
E
M
STEP 1
STEP 3
STEP 4
STEP 2
STEP 16
STEP 14
STEP 15
STEP 13

CODING
- 343038
CAPRI ASSEMBLY GUIDE
/ 5
5
10
11
12
13
14
1
4
9
10
11
11
12
13
14
Assemble panel (14) to entire body with hardware H.
(Repeat 30 times.)
HAMMER
REQUIRED
x30
HIT
H
12
12
13
14
12
12
13
14
12
11
Assemble hardware N2 (L/R) to panel (14) by using hardware E.
(Repeat 3 times for each hardware.)
N2 (L)
Hole at the center.
Third hole from the edge. Third hole from the edge.
x6
E
x6
E
x6
E
ROTATE ROTATE ROTATE
*Hardware N2 (L/R) shall be leaning against panel (10) or (11) when assembling.
SCREWDRIVER
REQUIRED
N2 (R)
12
11
12
13
14
N2 (L)
N2 (R)
12
10
12
13
14
N2 (L)
N2 (R)
12
Put all the drawer in place along the drawer slides.
11
15
16
16
STEP 18
STEP 19
STEP 17