Nureca Trumom Baby Car Seat User manual

CHILD RESTRAINT
GROUP 0+,I,II
SUITABLE FOR CHILDREN
FROM 0 TO 25KG
Trumom Baby Car Seat
INSTRUCTIONS FOR USE

1. Vital information-READ NOW
1.The customer can email at [e-mail], to obtain
future information on fitting the child restrain in specific cars.
2.The rigid items and plastic parts of a child restraint must be so
located and installed that they are not liable, during everyday
use of the vehicle to become trapped by a movable seat or in a
door of the vehicle.
3.Any straps holding the restrain to the vehicle should be tight;
any straps restraining the child should be adjusted to the
child's body; straps should not be twisted.
t
that
and that
4.The instructions can be retained on the child restraint for its
life period.
1
1.
2.
3.
4.
5.
6.
7.
0+
6-10
10-11
6.The device should be changed when it has been subject to
violent stresses in an accident.
7.It is dangerous to make any alterations or additions to the
device without the approval of the competent authority, and a
danger of not following closely the installation instructions
provided by the child restraint manufacturer.
8.When the chair is not provided with a textile cover, it should be
kept away from sunlight, otherwise it may be too hot for the
child's skin.
9.Children must not be left in their child restraint system
unattended.
10.Any luggage or other objects liable to cause injuries in the
event of a collision shall be properly secured.
11.The child restraint must not be used without the .cover
5.Do not use any load bearing contact points other than those
described in the instructions and marked in the child restraint.
2
12.The seat cover can not be replaced with any other than the
one recommended by the manufacturer, because the cover
constitutes an integral part of the restraint performance.
13.IMPORTANT-DO NOT use forward facing for children below
9 kg
8. Installing the safety group II............................12-13
9. How to dispose................................................14
10.Washing instructions.....................................14
e

2. Applicability
3. Safety instruction
Only suitable if the approved vehicles are fitted with 3 point
safety-belts,approved to UN/ECE Regulation No.16 or other
equivalent standards.
Mass Group 0+:0-13kg
Mass Group I: 9-18kg
Mass Group II: 15-25kg
0+,
3
4. Using safety seat in this way
Forward facing traffic direction
Back facing traffic direction
Vehicle is only fitted with 2-point safety belt
Vehicle is fitted with 3-point safety belt
Seat beside the driver
Rear seat
Rear middle seats Three-point Belt
Correct
Correct
Correct
Correct
Correct
Error
Error
4.1 Please carefully implement the Country
Traffic Safety Regulations
1.Do not use child restraint system in seating positions where there is an
air bag installed.
2.Please read the instruction manual carefully that how to use the airbag.
4
The child car seat is suitable for weight categories 0+ to II
(Group 0+,I,II),which means children with a body weight
between 0 kg and 25 kg
For children of weight categories II (15kg to 2 5kg) the
harness system must be removed and the vehicle’s 3-point
belt system used to secure the child.

The harness system is only permitted for children of group 0+,
Which means from 0 kg to 13 kg to use.
Incline adjuster
button
Belt guide group II
Red clip
slot

6.2 Reverse installation
Step 1.For Group 0+,the safety position of the safety seat must
only be used in the most reclined position(see Fig.1/a).The safety
seat must never be used in any other position(Fig.1/b).To adjust
the reclining position of the safety seat,press the red incline adjuster
button(Fig.2) ,Untill you reach the required position(Fig.3).
Fig.2
Step 2.The seat must always be rearfacing (Fig.4/a).If your car has
an airbag on the passenger seat,the safety seat must only be used on
the rear seat.
Fig.1/a
Step 3.secure the safety seat onto the car seat using the car seat
belt
Step 4.pass the lap part of the seat belt under the base of the safety
seat(A) into the two points marked by a blue label and fasten the
clip to the corresponding buckle(C)
Step 6.Place the red clip(D) on the shoulder belt directly upwards
at the place where lap and shoulder belt are splitted up.
8
Fig.1/b
C
B
D
Step7.Make sure that the belt is not twisted and strongly tightened
before you block the belt with the plastic clip.
Step 5.pass the upper diagonal part of the belt in the metallic guide(B)
Fig.3
Fig.4/a
Fig.4/c
Fig.4/b

7. Installing the safety group I
9
6.5 Height adjustment of head rest
Regularly check whether the head rest is optimal to your child.
The height of the head rest is set optimally to the size of your child,
when their he a d re s t s co m f o r t ably in the middle o f th e head
rest(Fig.1/a).
If the height of head rest in child car seat is not fit for your child,
please adjust the head rest upward or downward(Fig.1/b).
Fig.1/b
6.4.1
6.3
6.4
6.1
6.3
6.4.1
6.4.1
Step 1.For Group I,when positive installation the safety position
of t h e sa f e t y se a t ,the biggest a n g l e ca n be a d j u sted to the
third,place the child seat on the seat of the vehicle,ensuring it is
pressed firmly against the back of the vehicle seat.
Step 2.Move the Buckle Tongues to th e outsides of the cover.
Secure the Buckle Tongues with the fixings located in the sides of
the cover(A),then place the child on the child car safety seat(B).
Step 3.Fasten the child car seat in forward facing position on
either the passenger or rear seat of your car by using the 3 point
belt system which is installed in the car.
Step 4.Fasten the 3 point belt system (lap and shoulder belt)
through the upper metallic guide afterwards fasten the bucklein
the lock until a click is heard(D).
Fig.1/a
Place
on

11
8. Installing the safety group II
12
8.1 Remove the harness
Step 5.At the same time the lap belt is pulled through the 2 plastic
nibs(Fig.C).
Step 6.Place and fasten the red clip(E) on the shoulder belt directly
upwards atthe place where bassin and shoulder belt are splitted
DE
● Loosening the harness(see 6.3).
● To release the harness,press the red button on the buc kle
downwards(see point 6.4.1),
● Slide both of the harness off the harness connector(Fig.a),
take out the belt and remove the chest pad and buckle(Fig.b).
● Please adjust the seat to the biggest angle, you will see the
steel under the car seat(Fig.c).then,you can pull out the harness
from the solt which under the car seat(Fig.c).
● Pull the strap till the steel pole gets out of the solt(Fig.c,Fig.d).
The harness system must be moved from the seat(see point 8.1)
when used for these age groups 15kg-25kg.Only the 3-point vehicle
belt system can be used to buckle up the child car seat.
Fig.a
Fig.d
C
AB
Fig.c
Fig.b

9. How to dispose
Please observe the waste treatment of the country.
Please put the returnable plastics and metal parts into a
corresponding returnable container.
Use the original seat cover only .
Do not use the child safety seat without seat cover.
Use only water (under temperature of 30℃) with neutral
detergent to wash the cover. Hang it in the shade after
washing and do not wash by machine, spin dry or tumbledry
is not recommended.
Wash the plastic parts with warm water and neutral soap.
Do not wash with chemicals.
10. Washing instructions
13 14
Step 2.Place the child safety seat on the vehicle’s seat ensuring
it is firmly pressed against the car seat backrest(Fig.2).
Step 3.Place your child in the child car seat.
Step 4.Pull out the 3-point vehicle b e l t , sa f e ty b e l t p e n et r at e s
t h r o u g h th e seat belt guide to better a dapt to t h e b o y o n t h e
sh o u l d e r po s i t i o n of the seat belt, to avoid injury to the child's
neck and face , and then cross the child and the child safety seat and
allow it to lock in place .You will hear “click”(see fig.3)
Step 5.Th e f i na l t ig h t en i ng s a f et y b el t a n d m
.
a k e s u r e t h e
se a t - b e lt i s n o t twisted
Fig.2
Fig.3
8.2 Securing the child car seat with vehicle’s belt
Step 1.F o r G r o u p I I , w h e n p o s i t i v e
insta l l a t i on th e safe t y posit i o n of t he
safety seat ,the biggest angle only can
be adjusted to the first(see Fig.1). Fig.1
The vehicle's 3-point belt system may
only be used to buckle up children of the
age groups II (15kg-25kg).
The h arness s y s t e m mu s t be r e moved
from the seat(see point 8.1)when used
for these age groups 15kg-25kg.