NUTRIBULLET JUICER PRO User manual

User guide

2
Contents
Thank you for purchasing the nutribulletJuicer Pro™.
03 Important safeguards
08 What’s included
09 Assembly guide
10 Assembly & use
10 Usage instructions
17 Control panel
18 Juicing tips
22 Disassembly
24 Care and maintenance
25 Juice and unit storage
26 Troubleshooting guide
26 Replacement parts

3
GENERAL SAFETY
INFORMATION
• This juicer system has sharp
blades and moving parts, and
is NOT intended for use by
children who lack experience
and knowledge of its safe
operation. They require close
supervision and thorough
instruction on its proper use
and safe operation.
• This appliance shall not be used
by children. Keep the appliance
and its cord out of reach of
children.
• Children shall not play with
the appliance. The appliances
can be used by persons with
reduced physical, sensory or
mental capabilities or lack of
experience and knowledge
if they have been given
supervision or instruction
concerning use of the appliance
Important safeguards
Warning! To avoid the risk of serious injury, carefully
read all instructions before operating your nutribullet
Juicer Pro™. When using any electrical appliance, basic
safety precautions should always be observed,
including the following important information.
Save these instructions!
FOR HOUSEHOLD USE ONLY
in a safe way and if they under-
stand the hazards involved.
• To protect against fire, electrical
shock and injury to persons, do
not immerse the juicer, Motor
Base, cord or plug in water or
any other liquid.
• Turn the juicer OFF, then unplug
from the outlet when not in
use, before assembling or
disassembling parts and before
cleaning. To unplug, grasp the
plug and pull from the outlet.
Never pull from the power cord.
AVOID CONTACT WITH
MOVING PARTS.
• Regularly inspect the power
supply cord, plug, and actual
juicer for any damage
• Do not operate this or any
appliance with a damaged cord
or plug or after the appliance
malfunctions or is dropped or
damaged in any manner.

4
• If the supply cord is damaged,
it must be replaced by the
manufacturer, its service agent
or similarly qualified persons in
order to avoid a hazard
• The use of attachments not
recommended or sold by
nutribullet
®
may cause fire,
electric shock, or injury.
• This juicer is for household use
only. Do not use this juicer for
anything other than its intended
use. Do not use in moving
vehicles or boats. Do not use
outdoors. Misuse may cause
injury.
• Do not let the power cord hang
over the edge of a table or
counter top.
• Do not let the power cord touch
hot surfaces, such as a stove
or let it become tangled or
knotted.
• Always make sure the pulp
basin cover is securely in place
(with locking handle in its
upright and locked position)
before the motor is turned
on. Do not unlock the locking
handle while the juicer is in
operation.
Always ensure the juicer is
turned OFF after each use.
Before disassembling, make
sure the sieve has stopped
rotating and the motor has
completely stopped.
• Do not push food into the feed
chute with your fingers or
utensils. Always use the food
pusher provided. Do not place
your hand or fingers into the
feed chute when it is attached
to the juicer. If food becomes
lodged in the feed chute, use
the food pusher provided
or another piece of fruit or
vegetable to push it down. Turn
the motor o and ensure that
all moving parts have stopped
before disassembling the juicer
to remove the remaining pulp.
• Do not use the juicer if the
rotating sieve is damaged.
• Do not use the juicer without
the pulp basin and basin
cover attached to the motor
base. Please see assembly
instructions for proper
placement.
• Switch o the appliance and
disconnect from supply before
changing accessories or
approaching parts that move
in use.
ADDITIONAL
SAFEGUARDS
Remove and safely discard
any packaging material or
promotional labels before using
the juicer for the first time.
• To eliminate a choking hazard
for young children, remove and
safely discard the protective

5
cover fitted to the power plug of
this juicer.
• Do not touch the small cutting
blades/teeth on the bottom/
base of the sieve.
BLADES
ARE SHARP! HANDLE WITH
EXTREME CARE!
• Keep fingers away from the
sharp blade in the feed chute.
Always make sure the Juicer
is properly and completely
assembled before connecting to
power outlet and operating.
Ensure that the surface where
the appliance operates is stable,
level, clean and dry.
• Vibration can occur during
normal operation.
•
CAUTION: In order to avoid
a hazard due to inadvertent
resetting of the thermal cut-
out, this appliance must not be
supplied through an external
switching device, such as a
timer, or connected to a circuit
that is regularly switched on
and o by the utility.
• If extreme vibration occurs,
discontinue use and call
Customer Service.
• Do not use the appliance if the
rotating sieve or the protecting
cover is damaged or has visible
cracks.
• If the juicer leaks or there is a
spill under or around the juicer,
or onto the juicer itself, clean
and dry before continuing use.
• When using this juicer, make
sure there is adequate air space
around and under it for proper
air circulation.
This juicer is only designed to
juice fruits and vegetables.
Please refer to the juicing guide
to determine the correct speed
for the fruits and vegetables
selected for juicing. Do not use
any frozen fruits or vegetables.
• Hard fruits and vegetables will
put excess strain onto the motor
if a low speed is selected.
•
Remove rind from all citrus
fruits before juicing.
• Do not juice stone fruit unless
pits or seed stone has been
removed.
WARNING!
Do not leave the appliance
unattended while in use.
Keep hands, fingers, hair,
clothing as well as spatulas and
other utensils away from the
appliance during operation.
Keep the juicer clean. Refer to
care and cleaning section for
further information.
Any maintenance other than
cleaning should be performed
by an authorized electrician.
Do not attempt to repair or
service this juicer, contact

6
Customer Service for assistance
at nutribullet.com .
If any of the instructions or
warnings are not understood
please contact Customer
Service for assistance at
nutribullet.com .
Save these
instructions!
FOR HOUSEHOLD
USE ONLY

7

8
What’s included
1000 WATT MOTOR
BASE WITH LOCKING
HANDLE
PULP BASIN COVER
WITH 76 MM FEED
CHUTE
DUAL-SIZE FOOD
PUSHER
2 l PULP BASIN WITH
NO-DRIP SPOUT
STAINLESS STEEL SIEVE 800 ml JUICE PITCHER
JUICE PITCHER LID WITH
FROTH SEPARATOR CLEANING BRUSH TWO 350 ml GLASS STORAGE BOTTLES
118 ml FREEZER TRAY60 ml FREEZER TRAY

9
Assembly guide
dual-size food pusher
76 mm feed chute
locking handle
basin cover
2 l pulp basin
stainless steel
sieve (inside basin)
no-drip spout
800 ml juice
pitcher
multi-speed
control panel
motor base
juice pitcher lid

10
Assembly & use
1 Place the Motor Base on
a dry, level counter top.
Ensure the dial is set to the
“OFF” position and the unit is
unplugged.
2 Place the Pulp Basin on top of
the Motor Base. Align the Pulp
Basin with the Motor Base so
that the spout is aligned with
the dimpled side of the Motor
Base.
3 Align the Sieve with the motor
drive coupling and push
down until it clicks into place.
Handle the Sieve by gripping
the top edges being careful
not touch the sharp teeth on
the base of the Sieve . Ensure
the Sieve is properly seated
in place and securely inside of
the Pulp Basin.
4 Place the Basin Cover over
the Sieve and Pulp Basin.
The side “ears” on the Basin
Cover should align with the
“ears” on the sides of the Pulp
Basin.

11
5 Raise the Locking Handl e
and move it into the “ears” on
each side of the Basin Cover.
The Locking Handle should
be in a vertical position and
locked into place.
NOTE: if the Locking Handle is not
securely in place, the juicer will not
power on.
6 Swing the No-Drip Spout
cover up vertically so that it is
no longer covering the juice
spout.
7 Place the Juice Pitcher Lid on
top of the Juice Pitcher, and
open the locking lid latch.
8 Slightly angle the Juice
Pitcher and place it under the
juice spout. Align the spout
with the hole in the Juice
Pitcher Lid and level out the
Juice Pitcher . It will fit snuggly
into the spout to hold it in
place.

12
Usage instructions
1 Gather all of your desired
ingredients. Wash and
prepare them for juicing.
2 After the juicer is fully
assembled, plug the power
cord into an outlet.
NOTE: If no speed is selected after
10 minutes, the unit will power o

13
3 Select a speed to begin
juicing. The speed selected
will illuminate on the control
panel. You may start at
any speed and can toggle
between speeds as desired
depending on the type of
produce (refer to the chart on
page 18 for recommended
speeds for each type of
produce).
NOTE: always start the juicer before
putting food in the feed chute.
4 To operate the Dual-Size
Food Pusher , grip the outer
edge of the top of the pusher
with one hand and the bottom
of the pusher with the other
hand. Twist the top of the
pusher clockwise to unlock
the inner pusher. (The inner
pusher is thinner than the full
pusher.)

14
5 If you are using smaller
ingredients (smaller fruits,
leafy greens, stalk vegetables
like celery or carrots), place
the outer part of the pusher
into the chute, making the
chute more narrow. While the
motor is running, begin gently
guiding ingredients into the
internal chute using the inner
pusher.
TIP: When using the narrow chute
for juicing leafy greens, take
a small handful of greens and
squeeze them into a tighter bunch.
Place the bunch into the chute and
slowly push down into the Sieve.
Using the narrow chute will help to
prevent any pieces from flying up
out of the chute.
6 If you are using larger
ingredients, keep the feed
chute empty (creating a wider
chute) and lock the inner
pusher back inside the outer
pusher. While the motor is
running, begin gently guiding
your ingredients into the feed
chute using the full Dual-Size
Food Pusher .

15
7 Juice will begin to flow out of
the spout and into the Juice
Pitcher , while the pulp will be
separated and stored in the
Pulp Basin .
NOTE: You may alternate
between the two chute sizes
(narrow and wide) as you
are juicing.
WARNING: Do not use
excess force when pushing
food down with the Food
Pusher, as it will not allow
for maximum juice yield.
WARNING: Never use hands/
fingers or other tools to push
ingredients down the feed
chute into the Sieve. Only the
Food Pusher should be used
to push down ingredients.

16
10 Remove the Juice Pitcher
from under the spout. You
may close the Juice Pitcher
Lid and store juice in the Juice
Pitcher if desired.
NOTE: To do this, you’ll first need to
tip the Juice Pitcher forward at a
slight angle, so that the lid’s large
hole has some separation from the
spout, then you can slide out the
pitcher. This is the reverse of what
you did during assembly.
9 To stop juicing, press the speed
at which you are currently
juicing. To completely power o
the juicer, press the center power
button and wait for the Sieve to
stop spinning. Unplug the unit
after each use.
8 When the Pulp Basin is
completely full, it must be
emptied before continuing
juicing. See disassembly
instructions.
11 Immediately move the No-
Drip Spout cover downward
over the spout to avoid any
residual drips onto the unit
or onto the surface below the
juicer.
TIP: We recommend using your
left hand to pull the Juice Pitcher
away, while using your right hand
to swing the No-Drip Spout cover
down and over the spout opening.

17
Control panel
OFF:
Power is OFF . If the unit is ON ,
the center power button will be
illuminated. Pressing the center
button will turn the unit OFF .
LOW:
Best for juicing softer fruits and
vegetables.
HIGH:
Best for harder produce like
pineapples.
TURBO:
Best for juicing the toughest
vegetables like beets or carrots.
MULTISPEED CONTROL PANEL
& JUICING SETTINGS

18
Juicing tips
JUICING SPEED SELECTION GUIDE
INGREDIENTS SPEEDS SEASONS VITAMINS / NUTRIENTS
Apple Turbo All Year source of quercetin
Beets Turbo Summer / Fall / Winter excellent source of folate
Blueberry Turbo Summer good source of vitamin C
Broccoli Turbo Fall / Spring high in vitamin C, high in folate, good source of potassium
Brussels Sprouts Turbo Fall / Winter high in vitamin C, good source of folate
Cabbage Low Fall / Winter / Spring high in vitamin C
Carrots Turbo All Year excellent source of vitamin A, good source of vitamin C
Cauliflower Turbo Fall high in vitamin C, good source of folate
Celery Turbo All Year good source of vitamin C, good source of vitamin A
Cucumber High Summer good source of vitamin C
Fennel Turbo All Year good source of vitamin C and potassium
Ginger Turbo Fall contains vitamin C, magnesium, and potassium
Grapes Low Fall good source of vitamin K
Grapefruit Low Winter high in vitamin A, high in vitamin C
Kale High Fall / Winter / Spring excellent source of vitamin A and vitamin C, good source of calcium and potassium
Kiwi Low Fall / Winter / Spring high in vitamin C, good source of potassium and vitamin E
Lemon Low All Year high in vitamin C
Lime Low All Year high in vitamin C
Melons (all) Low Summer high in vitamin A, high in vitamin C
Orange Turbo Winter high in vitamin C
Peaches High Summer good source of vitamin C
Pears High Fall / Winter good source of vitamin C
Pineapple High Fall / Winter / Spring high in vitamin C
Plums High Summer good source of vitamin C
Raspberries Low Summer / Fall high in vitamin C
Spinach Low Fall / Spring high in vitamin A, vitamin C, iron, and folate, good source of magnesium
Sweet Potato (raw) Turbo Fall / Winter good source of potassium, high in vitamin A and vitamin C
Tomatoes Low Summer high in vitamin A, high in vitamin C, good source of potassium

19
INGREDIENTS SPEEDS SEASONS VITAMINS / NUTRIENTS
Apple Turbo All Year source of quercetin
Beets Turbo Summer / Fall / Winter excellent source of folate
Blueberry Turbo Summer good source of vitamin C
Broccoli Turbo Fall / Spring high in vitamin C, high in folate, good source of potassium
Brussels Sprouts Turbo Fall / Winter high in vitamin C, good source of folate
Cabbage Low Fall / Winter / Spring high in vitamin C
Carrots Turbo All Year excellent source of vitamin A, good source of vitamin C
Cauliflower Turbo Fall high in vitamin C, good source of folate
Celery Turbo All Year good source of vitamin C, good source of vitamin A
Cucumber High Summer good source of vitamin C
Fennel Turbo All Year good source of vitamin C and potassium
Ginger Turbo Fall contains vitamin C, magnesium, and potassium
Grapes Low Fall good source of vitamin K
Grapefruit Low Winter high in vitamin A, high in vitamin C
Kale High Fall / Winter / Spring excellent source of vitamin A and vitamin C, good source of calcium and potassium
Kiwi Low Fall / Winter / Spring high in vitamin C, good source of potassium and vitamin E
Lemon Low All Year high in vitamin C
Lime Low All Year high in vitamin C
Melons (all) Low Summer high in vitamin A, high in vitamin C
Orange Turbo Winter high in vitamin C
Peaches High Summer good source of vitamin C
Pears High Fall / Winter good source of vitamin C
Pineapple High Fall / Winter / Spring high in vitamin C
Plums High Summer good source of vitamin C
Raspberries Low Summer / Fall high in vitamin C
Spinach Low Fall / Spring high in vitamin A, vitamin C, iron, and folate, good source of magnesium
Sweet Potato (raw) Turbo Fall / Winter good source of potassium, high in vitamin A and vitamin C
Tomatoes Low Summer high in vitamin A, high in vitamin C, good source of potassium

20
PROPER PRODUCE PREP
Prepare fruit and veggies before
inserting them into the juicer:
• Properly clean produce
(rinse with produce wash, or
lukewarm water and apple
cider vinegar).
• Peel or remove skin as needed,
and chop food items down
to the right size – just small
enough to fit easily into the feed
chute, without having to force
the pieces down with the
Food
Pusher.
• Remove rind from all citrus fruits
before juicing.
• Remove large pits and seeds
from stone fruits before juicing.
FEED CHUTE
Selecting which Food Pusher to
use (narrow or wide) aects feed
chute thickness. If you pull out the
thinner inner food pusher from
within the full pusher, you’ll place
the outer part into the chute,
making the chute narrow. If you
use the full (wide) pusher, the feed
chute will be wider.
• Never place your hand or
fingers into the feed chute when
it is attached to the juicer.
• Always start the juicer before
adding food to the feed chute.
The unit must be running when
items enter it.
• Do not overload the feed chute.
Items must be added gradually,
at a pace the juicer can keep up
with.
• Use only the provided
Food
Pusher to push food into the
feed chute. Never use fingers,
utensils, or any other apparatus.
• Never use excessive force to
push items into the feed chute.
• When juicing, ensure all
produce has moved through the
feed chute and into the
Sieve
before adding more.
• If any food gets stuck in the feed
chute, use the
Food Pusher to
move it down the chute and into
the Sieve .