Nutricia Flocare Infinity+ How to use

Flocare Infinity+
Short Manual
Preparation and start of the pump
Operating instructions
>Open the pump door by pressing up on the lower wall (A) and rotating the door upwards (B) at the same time (fig. 1).
>Position the looped section of the silicone tubing around the rotor (fig. 2).
>Stretch slightly to seat the cassette into the pump (fig. 3).
>Close the pump door (fig. 4).
>The pump is now ready to be switched on.
1
2
3
4
5
Clearing pump
memory and priming
the feeding set
>When switching the pump on or off, press this key for 2 seconds.
> Pressing this key will clear the pump memory.
> Pressing this key for 2 seconds will automatically prime the feeding set.
>Connect the feeding set with the feeding tube and choose appropriate feeding program , or .
1 2 3 4
Preparation and start of the pump
A
B
clr
fill set
1 2 3
Continuous
feeding
Continuous feeding
and pre-set dose
Bolus feeding
400 ml/h
1 ml/h
400 ml/h
1 ml/h
500 ml
1 ml
4000 ml
1 ml
12.00 h
0.30 h
4000 ml
1 ml
high (600 ml/hr)
low (400 ml/h)
>
>
>
>
>
>
>
>
>
>
>
>
>
>
1
2
3
ml/h
ml/h
bolus ml/int h
start/stop
start/stop
ml/h
start/stop
volume ml
bolus ml/int h
volume ml
+
+
+
+
+
+
+
–
–
–
–
–
–
–

Flocare Infinity+
Problem solving
instructions
Error messages and instructions
Please refer to detailed Instructions for Use for additional information
171101 / BP&MC 11090802
>Press to switch off the pump > Insert the Flocare®Infinity™set into the pump following
instructions for use >Restart the pump.
>The pump has been untouched in hold mode for over 3 minutes >Extend the hold mode by a further
3 minutes by pressing >Program the pump and press to start the pump.
>The programmed dose / volume has been administered >Switch off the pump by pressing
for 2 seconds > Clear the memory by pressing .
>No flow rate is installed > Make sure the correct flow rate is programmed.
>The door is not correctly closed > Make sure the door is properly closed prior to starting a feeding
program.
>Check if the set is inserted correctly and check the air sensor > Remove the air in the set by using
key.
>Connect the adaptor to the pump and mains and charge the pump for approx. 6 hours. During charging
the pump can be used.
>Battery failure >Please refer the pump for service.
>Press >Check the feeding set (IN) or feeding tube (OUT) for blockages >Reinsert
the set and start the pump, if necessary clean the sensors.
>Electronic error >Switch the pump off, make sure the pump door is closed and turn the pump back
on >If the error persists, please refer the pump for service.
>The wall outlet or the adaptor does not work >Connect to another wall outlet >If there is still no
symbol, request replacement of the adaptor.
NO SET
PUSH STRT
END OF DOSE
PROG
DOOR
AIR
BATT
BATT E + F
OCC IN
>The programming feature is blocked in the set-up mode of the pump >Refer to instruction booklet
to de-block.
LOCK
ER01 - ER99
NO PLUG SYMBOL
OCC OUT
Problem Instructions
(while the pump is
connected to the mains)
clr
fill set
start/stop start/stop
start/stop
>Stop the pump by pressing the >Let it run briefly by repressing the
key >Stop the pump again with key, ensuring there has been no OCC OUT alarm >
Remove the set from the pump and reinsert it into the pump >Restart the pump by pressing
.
OCC OUT
(repeated)
start/stop start/stop
start/stop
start/stop