Nuvico CT-2M-MP20FH User manual

CT-2M-MP20FH
20x Full-HD Mini-PTZ
HD-TVI CAMERA
Please read this guide thoroughly before use and keep it handy for future reference.
“Nuvico surveillance equipment is designed to be installed and served only by a
trained, state-licensed professional installer”.

2
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO
NOT INSERT ANY METALLIC OBJECTS THROUGH THE
VENTILATION GRILLS OR OTHER OPENINGS ON THE
EQUIPMENT.
CAUTION
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLEPARTSINSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

3
FCC COMPLIANCE STATEMENT
CE COMPLIANCE STATEMENT
WARNING
This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequatemeasures.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme
NMB-003 du Canada.
CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
FCC INFORMATION: This equipment has been tested and found to
comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

4
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves,
or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade or the
third prong is provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
15. CAUTION –THESE SERVICING INSTRUCTIONS ARE FOR USE BY
QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF
ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN
THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU
ARE QUALIFIED TO DO SO.
16. Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed
Class 2 power source only.

5
Table of Contents
Chapter 1 —Introduction ................................................................................................. 6
1.1 Features...............................................................................................................................6
Chapter 2 —Installation and Configuration.....................................................................7
2.1 Package Contents................................................................................................................7
2.2 Installation............................................................................................................................8
2.3 Basic Configuration of Dome Camera System................................................................11
2.4 Setting Dome Camera Address (ID).................................................................................. 12
2.5 Setting Dome Camera Video Type & Coaxitron Protocol................................................12
2.6 Connections....................................................................................................................... 13
2.7 Getting Started........................................................................................................................14
Chapter 3 —Program and Operation.............................................................................15
3.1 Dome Camera Selection....................................................................................................15
3.2 Accessing the On-Screen Menu Utility ............................................................................15
3.3 How to control the On-Screen Menu Utility..................................................................... 15
3.4 Auto Scan (Shortcut: SCAN) ............................................................................................16
3.5 Preset (Shortcut: PRST)....................................................................................................18
3.6 Shortcut of Preset Program.............................................................................................. 20
3.7 Tour (Shortcut: TOUR) ......................................................................................................20
3.8 Pattern (Shortcut: PTRN)..................................................................................................22
3.9 Privacy Zone...................................................................................................................... 23
3.10 Camera Menu................................................................................................................... 24
3.11 Dome Communication.....................................................................................................27
3.12 Alarm................................................................................................................................28
3.13 Dome Setup .....................................................................................................................29
Appendix A —Specifications.........................................................................................36
Appendix B —Troubleshooting.....................................................................................38

6
Chapter 1 —Introduction
1.1 Features
The ptzdome camera and the keyboard controller make up the building blocks for any
surveillance/security system. Using multiple keyboard controllers and multiple dome cameras, no
place is too large for monitoring. Extensible and flexible architecture facilitates remote control
functions for a variety of external switching devices such as multiplexers and DVRs.
 Built-in optical power zoom camera with True Night Shot function
 240 Preset positions with the individual camera AE setup
 8 Tours consist of Presets, Patterns, Auto Scans and other Tours can be programmed with over
300 functions and preset locations. While moving, each Preset scan can be watched in smooth
Vector Scan mode.
 16 Auto Scans with the normal, the vector, and the random mode and the endless Auto-Pan with
13 speed steps
 8 Patterns (up to 500 seconds) and 24 Privacy Zones
 4 Alarm inputs, 2 Alarm outputs (5VTTL)
 Variable speed from 0.1/sec. to 380/sec.
Three Variable speed (SLOW, NORMAL, TURBO)
Turbo speed is 380/sec. with Ctrl key pressed.
 Pan/Tilt speed is inversely proportional to the zoom ratio with the option.
 Maximum speed is 380/sec. when Preset command.
 Auto Calibration from 0.1to 6(Tilt range is -10to 190)
 Programmable user preferences (alarm, preset, title, etc.)
 180Digital Flip
 Up to 3999 selectable camera addresses
 Function Run menu using DVR without function key (Pattern, Scan …)
 Built-in RS-485 receiver driver
 12VDC or 24VAC for Dome
 Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2 power source only.

7
Chapter 2 —Installation and Configuration
2.1 PackageContents
The PTZdome camera is designed with compact, small size, hard dome camera housing.
The housing is constructed of aluminum, steel and plastic. The housing is designed to be mounted
on a wall or a ceiling. The housing meets the Protection Classification IP66 standards for dust and
moistureresistance.
* Dome Camera
1
* Instruction Manual (This Document)
1
* Template Sheet
1
* Mounting Bracket
1
* Safety Lanyard
1
* Accessory Kit
1
1) Mounting screws (PH6 x 35.0)
(4)
2) Plastic anchors
(4)
3) O-Rings
(4)
4) Torx wrench
(1)
* Accessory Connector
1
1) 2-Pin Terminal Block
(1)
2) 3-Pin Terminal Block
(1)
3) 4-Pin Terminal Block
(1)
4) 5-Pin Terminal Block
(1)

8
2.2 Installation
The PTZ dome camera is for use in surface or pendent mounting applications, and the mounting
member must be capable of supporting loads of up to 10 lb (4.5 kg). (Pendent mounting must use
pendent mount accessory.)
The dome camera’s mounting bracket should be attached to a structural object, such as hard wood,
wall stud or ceiling rafter that supports the weight of the dome camera.
CAUTION: A silicone rubber sealant must be applied to seal the housing to secure
waterproofing.
2.2.1 Locking Dome Camera
A. Make screw holes on the ceiling using the supplied mounting Template Sheet (Figure A).
B. Fix the Mounting Bracket to the ceiling using supplied Anchors (4x) and Mounting Screws (4x)
(Figure B).
C. Hook up the Safety Lanyard to the Safety Lanyard Hook of the Mounting Bracket (Figure C).
D. Align the locking tab on the bracket and the locking slot on the base of the dome (Figure D).
E. Turn the dome to the counterclockwise about 10 degree to the locked position (Figure E).

9
CAUTION: Before installing mounting bracket to surface pre-adjust the four mounting
screws "A" on the base of the dome camera to best match the mounting bracket
locked position. Unscrew the locking screw on the side of the dome's base and fit
the tab of the mounting bracket into the locking slot. Screws "A" should not be
too tight or too loose when the dome is in the locked position. After setting the
proper positions of screws "A" remove the mounting bracket and install it to the
proper surface. If it is too difficult to lock the dome in position after the mounting
bracket has been installed readjust the screws "A" by unscrewing them a small
amount and try to install dome camera again.

10
2.2.2 Heater Kit Installation (Optional)
1. Assemble the Heater board to two bossed with screws.
Take a reference "B" in the bottom case as below.
2. Place the Heater in the slot "A".
Heater cable should be placed away from the Main Board.
3. Plug the power connector to the socket "C" (J1) of the Heater Board.
4. 24VAC is recommended to use for the camera power for stable operation with heater kit.
• HEATER (IF APPLICABLE)
Power Supply
24VAC
PowerConsumption
10W
Heater ON
at 59°F (15°C)
Heater OFF
at 77°F (25°C)
• POWER
Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2
power source only.
CAUTION: Please reset the camera after 30 minutes when installing it in situations colder
than -10°C.

11
2.3 Basic Configuration of Dome Camera System
No.
Connector
Wire Color
Description
1
3-pin terminal block
RED
24VAC or 12VDC+
WHITE
24VAC or 12VDC-
2
2-pin terminal block
GREEN
RS-485+
BLUE
RS-485-
3
5-pin terminal block
GRAY
ALARM INPUT 1
VIOLET
ALARM INPUT 2
ORANGE
ALARM INPUT 3
SKY BLUE
ALARM INPUT 4
BLACK
GND
4
4-pin terminal block
YELLOW
ALARM OUTPUT 1
BLACK & WHITE
GND
SKY BLUE & BALCK
ALARM OUTPUT 2
ORANGE & BLACK
GND
5
BNC jack
BLUE
HD-TVI OUTPUT
6
BNC jack
BLACK
CVBSOUTPUT
The dome camera must be installed by qualified service personnel in accordance with all local and
federal electrical and building codes.

12
NOTE: Open the DIP switch cover and change the setting of DIP switch.
The cover should be closed after setting DIP switch.
2.4 Setting Dome Camera Address (ID)
To prevent damage, each dome camera must have a unique address (ID).
The factory default setting is 1.
Refer to ‘3.11 Dome Communication’ section for detailed information.
2.5 Setting Dome Camera Video Type & Coaxitron Protocol
S1
You can set video type with D1 in S1.
S1-D1
Video Type
OFF
HD-TVIOUTPUT
ON
Reserved
You can set coaxitron protocol with D2 and D3 in S1.
S1-D2
S1-D3
HD-TVI OUTPUT
OFF
OFF
Nuvico-C
ON
OFF
Pelco-C
OFF
ON
Reserved
ON
ON
Reserved

13
2.6 Connections
• Connecting to the RS-485
The dome camera can be controlled remotely by an external device or control system, such as a
control keyboard, using RS-485 half-duplex serial communications signals.
• Connecting HD-TVI Output connector
Connect the HD-TVI/AHD output (BNC) connector to the monitor or video input.
• Connecting CVBS Output connector
Connect the CVBS output (BNC) connector to the monitor or video input.
• ConnectingAlarms
- A1,A2,A3,A4 (Alarm Input 1,2,3,4)
You can use external devices to signal the dome camera to react on events. Mechanical or
electrical switches can be wired to the A1,A2,A3,A4 (Alarm Input 1,2,3,4) and G (Ground)
connectors.
See Chapter 3 —Program and Operation for configuring alarm input.
- G (Ground)
NOTE: All the connectors marked G or GND are common.
Connect the ground side of the alarm input and/or alarm output to the G (Ground) connector.
- AO1,AO2 (5VTTL Alarm Output 1,2)
The dome camera can activate external devices such as buzzers or lights. Connect the device
to the AO1,AO2 (Alarm Output 1,2) and G (Ground) connectors.
See Chapter 3 —Program and Operation for configuring alarm output.
• Connecting the Power
Connect power of 24VAC for the dome camera.
Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2 power source only.

14
2.7 Getting Started
Once installed apply power to the dome camera. The dome camera will start a configuration
sequence.
FUNCTIONTITLE
001 AF AE STATUS of
FOCUS and AE
INFORMATION
DISPLAY EMPTY DATA
ALARMDISPLAY ALARM:1
DOMEID:0001
360.0 090.0
CAMERA TITLE & ID
PAN & TILT ANGLE
OSD Position

15
CAM
1
0
Chapter 3 —Program and Operation
3.1 Dome Camera Selection
Before you program or operate a dome camera, you must select the dome camera by pressing
+ keys.
Example:Pressing
, + keys sequentially will select dome camera 10. The selected
dome camera ID will be displayed on the LCD monitor of the keyboard controller.
3.2 Accessing the On-Screen Menu Utility
You can call up the On-screen menu utility on your monitor by pressing the
keyboard controller, the following On-screen menu utility will appear: key on the
3.3 How to control the On-Screen Menu Utility
Function
Button
Call the On-screen menu utility.
MENU
Navigate through the menu items.
Joystick up or down
Go into the sub-menu items.
Joystick left or right or IRIS Open
Change value.
Enter the editing title mode.
Joystick left or right or
Zoom handle twist or Tele , Wide
Change value of angle.
CTRL + Joystick
Enter the changing angle mode.
IRIS Open
Exit the changing angle mode.
IRIS Close
Escape(EXIT)
ESC
DOME MENU
AUTO SCAN
PRESET
TOUR
PATTERN
PRIVACY ZONE
CAMERA
DOME COMMUNICATION
ALARM
DOME SETUP
EXIT(ESC TO EXIT)
No.
CAM
MENU

16
CTRL
3.4 Auto Scan(Shortcut: SCAN)
The Auto Scan supports up to 17 programmed angles at user-programmable speeds.
Follow these steps to program Auto Scan:
NUMBER 01 ~ 08, 10 ~ 17, 09: AUTO-PAN mode.
TITLE up to 6 characters
MODE NORMAL, VECTOR, RANDOM(AUTO-PAN mode: NORMAL, RANDOM only).
NORMAL Move from start point to end point in panning only
VECTOR Move from start point to end point including tilt and zoom simultaneously and
linearly.
RANDOM Move randomly between the start point and the end point
SPEED 1 ~ 13 step, the lower number means the slower speed.
SCAN DIR Set the Scan direction, CCW (Counter Clock Wise), CW (Clock Wise).
SWAP Swaps the start point for the end point.
DWELL Set the dwell time at the both end, 01 ~ 99 seconds.
1. Press the key to enter the Auto Scan menu directly. Or press the MENU key to display
the main menu on the monitor. Scroll to Auto Scan and push the Joystick to the right.
2. Select “NUMBER”and set the desired number by pushing the to the left or right.
3. Select “TITLE”and twist the to enter the title edit mode.
4. Twist the
pushing t
or
to change the alphanumeric characters and move the next position by to
the left or right. Or move down to the character table and press the key
at the desired character then the cursor position moves to the next
position automatically. Push the Joystick to the left or right at the “ALL DELETE” field to delete
all characters. Push the Joystick to the left or right at the “EXIT” field to finish title edit menu.
TITLE EDIT MENU
(CTRL KEY)
A01
*
A B C D E F G H I J
K L M N O P Q R S T
U V W X Y Z 0 1 2 3
4 5 6 7 8 9 ( )
ALL DELETE
EXIT(ESC TO EXIT)
AUTO SCAN
NUMBER :
TITLE :
MODE :
SPEED :
START ANGLE :
END ANGLE :
SCAN DIR :
SWAP :
DWELL :
SAVE AND EXIT(ESC
SETUP
01
A01
NORMAL
5 STEP
----- -----
----- -----
CCW
OFF
03 SEC
TO CANCEL)
SCAN
Joystick
Joystick
Joystick
he
Joystick
IRIS Open

17
2
3
5. Select “MODE”and “SPEED”.
6. Select “START ANGLE”. Hold down the key while selecting the start position using the
Joystick. Current panning position will be displayed. Release the key to complete the
selection of the start position. Or press the
the desired position and the zoom position. key then the “CONTROL” displays. Move ey then the “CONTROL”
disappears. To adjust at the 0.1 degree interval, twist the
field. at the pan field and the tilt
7. Select “END ANGLE”. Hold down the key while moving the to select the end
position. The end position angle should be larger than start position. Release the key to
complete the selection of the end position. Or press the key then the “CONTROL”
displays. Move the desired position and the zoom position. Press the IRIS Close key then the
“CONTROL” disappears. To adjust at the 0.1 degree interval, twist the Joystick at the pan field
and the tilt field.
8. Set “SCAN DIR”to CCW or CW.
9. Select “SWAP”, Set to ON to exchange the start angle and the end angle.
10. Set “DWELL time”.
11. Select “SAVE AND EXIT”and push the to the right or press the key.
Press the ESC or IRIS Close key to exit the program without saving.
NOTE: Pressing the key delete stored data at the angle field.
To set the position using the Preset position:
a. Before entering the Auto Scan menu, select a Preset position as a starting point for Auto Scan.
Example: + keys and do step 1 to 5. In step 6, just press the key at the start
angle position, the current position will be displayed as a start position.
b. Save and Exit from the menu.
c. In normal mode, call a Preset to be the end point of Scan. Press + keys then press the
SCAN key to enter the Auto Scan menu. Move the cursor position to END ANGLE. Just press
the CTRL key at the end angle position. Save and exit from the menu.
Press the
as below. key on the angle field to display with the small OSD. Then the screen will show
The setting procedure is the same as above.
NOTE: 09: AUTO-PAN mode (endless panning)
AUTO SCAN AREA SETUP
(CTRL KEY)
NUMBER 01
START : ----- -----
END : ----- -----
EXIT(ESC TO EXIT)
CTRL
CTRL
IRIS Open
Press the
IRIS Close
k
Joystick
CTRL
Joystick
CTRL
IRIS Open
Joystick
IRIS Open
HOME
PRST
CTRL
PRST
SCAN

18
3.5 Preset(Shortcut: PRST)
If you need to view specific places routinely, you should program Presets. A Preset is a
programmed video scene with automatic pan, tilt, zoom, focus, and AE settings. Once
programmed, placing the number position and pressing the key on your controller calls up
that Preset automatically. In addition, Presets may be assigned the “home” position for the dome
camera. As many as 240 Presets, whose positions are saved in the dome’s firmware, may be
programmed.
There are eight pages of Preset menu. Each page has 30 Presets. Pages can be scrolled by
pushing the to the left or right on the first or last No. of Preset.
- Blank Preset position
* Position has the Preset
! Current cursor position
Follow steps below to store the Preset positions:
1. Press the key to enter the Preset menu directly. Or press the key to display the
main menu on the monitor. Scroll to Preset and push the to the right.
2. Select the blank Preset position to be stored by pushing the up, down, right, or left.
3. After selecting a blank position, press and hold the
direction of the camera and lens. key. Use the to control the
4. After aiming the camera (view direction and lens control), release the CTRL key. The cursor will
be on the “TITLE”after saving data then twist the or press the Tele or key to
edit the Preset title. Follow the procedure of the Auto Scan above to edit titles.
5. Select “CAMERA SET”and push the
displays. to the left or right. Then the Preset camera setup
Set FOCUS AUTO, MANUAL, ONE PUSH
Set MOTION OFF, ON
PRESET CAMERA SETUP
FOCUS : AUTO
MOTION: OFF
MOTION SETUP
AE SETUP
SAVE AND EXIT(ESC TO CANCEL)
NUMBER
PRESET SETUP
: 001
TITLE : ------
CAMERA SET
DWELL : -- SEC
1 2 3 4 5 6 7 8 9 0
- * - - - - - - - -
- - - - - - - - - -
- - - - - - - - - -
NEXT PAGE
SAVE AND EXIT(ESC TO CANCEL)
PRST
Joystick
PRST
MENU
Joystick
Joystick
CTRL
Joystick
Joystick
Wide
Joystick

19
Select “MOTION SETUP”and push the
displays. to the left or right. Then the MOTION setup
Set SENSITIVITY 00 ~ 20
SetRESOLUTION 01 ~ 04
Set POSITION ALL, CENTER
Set DELAY 00 ~ 05 seconds
Set OUTPUT OFF, OUT1, OUT2
Set HOLD TIME 03 ~ 99 seconds
Select “AE SETUP”and push the to the left or right. Then the AE setup displays.
Refer to the AE SETUP in the camera setup.
6. Set “DWELL time”. (03 ~ 99 seconds)
7. To select the next page of Presets, scroll the page by pushing the
the first or last columns of the menu.
8. Repeat step 2 through 7 for each additional Preset position.
to the left or right on
9. Select “SAVE AND EXIT”and push the to the right or press the key. Press
the or IRIS Close key to exit the program without saving.
NOTE: Press the HOME key at programmed Preset position (*) to delete a programmed
Preset view.
The position, which is marked with the *, already has the Preset view assigned. Press the
key on the * to review the stored Preset. The camera will show the stored Preset scene.
Hold down the key while selecting the desired scene using the Joystick. Current position
will be displayed. Release the key to complete. Or press the IRIS Open key then the
“CONTROL” displays. Move the desired position and the zoom position. Press the key
then the “CONTROL” disappears. Select “EXIT” and push the to the right.
PRESET AREA SETUP
(CTRL KEY)
NUMBER 001
PAN TILT
000.0 000.0
EXIT(ESC TO EXIT)
MOTION SETUP
SENSITIVITY: 10
RESOLUTION : 02
POSITION : ALL
DELAY : 00 SEC
OUTPUT : OFF
HOLD TIME : 03 SEC
EXIT(ESC TO EXIT)
Joystick
Joystick
Joystick
Joystick
ESC
IRIS Open
PRST
CTRL
CTRL
IRIS Close
Joystick

20
1
0
1
CTRL
3.6 Shortcut of Preset Program
After selecting the desired scene, press No. (1 to 240), and press the
and keys
subsequently. The current view will be stored to the selected Preset number if the Preset number
is empty. If selected Preset number is not empty, “OVER WRITE”message will be displayed on
the monitor and select the “OK” and push the to the right to overwrite.
Example : , , + + keys will store current view as Preset no. 101. In this case,
focus will be programmed as Auto, dwell time will be set to 3 second, and the current
AE mode will be programmed.
3.7 Tour(Shortcut: TOUR)
There are 8 programmable Tours. Each Tour consists of up to 42 Preset positions, Patterns, Scans
or other Tours (second-level). Using second-level Tours, it can be expanded to over
300 functions in a single Tour.
--- Blank position
SCAN TYPE NORMAL,VECTOR
DWELL 03 ~ 99 seconds
003 Preset (1 ~ 240)
A04 Auto Scan (1 ~ 8, 10 ~ 17)
P01 Pattern (1 ~ 8)
T02 Tour (1 ~ 8)
Follow the steps below to program the Tours:
1. Press the key to display the main menu on the monitor. Scroll to Tour and push the
to the right to enter the Tour menu. Or just press the key on the keyboard.
2. Select “NUMBER”and set the desired number by pushing the to the left or right.
3. Choose a blank position to be programmed by pushing the up, down, right, or left.
TOUR FUNC SETUP
(CTRL KEY)
DWELL : -- SEC
003 A04 --- --- ---
--- --- --- --- ---
--- --- P01 --- ---
--- T02 --- --- ---
--- --- --- --- ---
--- --- --- --- ---
--- --- --- --- ---
--- --- --- --- ---
EXIT(ESC TO EXIT)
TOUR SETUP
NUMBER
TITLE
SCAN TYPE
SPEED
TOUR FUNC
: 01
: T01
: NORMAL
: -- STEP
SAVE AND EXIT(ESC TO CANCEL)
CTRL
PRST
Joystick
PRST
MENU
Joystick
TOUR
Joystick
Joystick