NXP Semiconductors MPC5748G Low Cost EVB User manual

NXP Semiconductors
User Guide
Document Number: MPC5748GLCEVBUG
Rev. 1, 08/2016
MPC5748G Low Cost EVB User Guide
(MPC5748G-LCEVB)
© 2016 NXP B.V.
Downloaded from Arrow.com.

Table of Contents
1. Introduction ........................................................................................................................................................................3
2. LCEVB Features ...................................................................................................................................................................3
2.1. Differences to the Customer EVB...............................................................................................................................4
3. Configuration Overview ......................................................................................................................................................6
4. Initial Setup .........................................................................................................................................................................7
4.1. Power Supply Configuration.......................................................................................................................................7
4.1.1. Power Input Connector .....................................................................................................................................7
4.1.2. Power Switch .....................................................................................................................................................7
4.1.3. Power Status LED...............................................................................................................................................8
4.1.4. MCU and Peripheral Voltage Configuration ......................................................................................................8
4.2. Reset Control (SW3) ...................................................................................................................................................8
4.2.1. Reset LEDs .........................................................................................................................................................9
4.3. MCU Clock Configuration .........................................................................................................................................10
4.4. Debug Connector (P1) ..............................................................................................................................................10
4.4.1. Debug Connector Pinout .................................................................................................................................10
5. Communications & Memory Interfaces: ...........................................................................................................................11
5.1. CAN Interfaces (P2, P3) ............................................................................................................................................11
5.2. LIN Interfaces (P6, P7) ..............................................................................................................................................12
5.3. USB RS232 Serial Interface (P11)..............................................................................................................................12
5.4. USB HOST Interface (P4)...........................................................................................................................................12
5.5. Ethernet Interface (P5).............................................................................................................................................13
5.6. FlexRay (P8, P9, P10) ................................................................................................................................................13
6. User Interface (I/O) ...........................................................................................................................................................14
6.1. GPIO Matrix..............................................................................................................................................................14
6.2. User Switches (SW4, SW5) .......................................................................................................................................15
6.3. Hex Encoded Switch (SW1) ......................................................................................................................................15
6.4. User LED’s (DS1, DS2, DS3, DS4)...............................................................................................................................16
6.5. ADC Input Potentiometer (RVAR, RV1) ....................................................................................................................16
7. MCU Port Pin LCEVB Functions .........................................................................................................................................17
8. Appendix ...........................................................................................................................................................................18
9. Revision History.................................................................................................................................................................34
MPC5748G Low Cost EVB User Guide, Rev. 1, 08/2016
2NXP Semiconductors
Downloaded from Arrow.com.Downloaded from Arrow.com.

1.Introduction
This user guide details the setup and configuration of the NXP MPC5748G Low Cost Evaluation
Board (hereafter referred to as the LCEVB). The LCEVB is intended to provide a mechanism for easy
evaluation of the MPC5748G family of microcontrollers, and to facilitate basic hardware and software
development.
Note that the LCEVB has a limited feature set compared to the main MPC574xG customer EVB and is
intended for evaluation purposes. Customers moving to serious development activities are recommended to
purchase the fully functional customer EVB which also has device specific daughter cards.
The LCEVB is intended for bench / laboratory use and has been designed using normal
temperature specified components (+70° C).
This product contains components that may be damaged by electrostatic discharge. Observe
precautions for handling electrostatic sensitive devices when using the LCEVB.
The user guide is intended to be read alongside the respective MCU documentation available at
www.nxp.com and includes:
Reference Manuals 

Product Data Sheets 

Application notes 

Device Errata 

2.LCEVB Features
The LCEVB provides the following key features:
Single 5 V DC external power supply input with on-board 3.3 V regulator. Power is supplied via
a 2.1 mm barrel style power jack. 

Simple jumper less configuration (enhanced configuration is possible via 0 Ohm Resistors
and optional jumpers if required). 

Master power switch and regulator status LED. 
USB Serial interface. 
2 x High Speed CAN transceiver routed to 3-way headers. 
2 x LIN interfaces routed to 3-way headers. 
Main clock supplied from on board crystal. 
User reset switch with reset status LED’s. 

Ethernet PHY and RJ45 socket (configured for MII mode). 
USB Type A Host interface. 
2 x FlexRay interfaces with standard 2-pin connectors. 
14-pin JTAG connector. 
MPC5748G Low Cost EVB User Guide, Rev. 1, 08/2016
3NXP Semiconductors
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

4 user LED’s wired to MCU ports. 

2 user pushbutton switches wired to MCU ports. 
Hexadecimal encoded switch wired to 4 MCU ports. 
Simple potentiometer connected to analogue input channel. 
2.1. Differences to the Customer EVB
Note that the GPIO pins used for peripherals on the LCEVB are the same as those used on the
customer EVB. This ensures maximum code compatibility between the 2 boards, making it easy to
migrate from one board to the other
Table 1. Customer EVB vs LCEVB features
Feature
Customer EVB
LCEVB
MCU Support
Custom MCU Daughter cards for
Soldered 176QFP MPC5748G
multiple devices (socketed)
Power Supply
External 12 V
External 5 V (Caution)
On Board Regulators (and LED’s)
5
V, 3.3 V, 1.25 V (combination of
3.3 V Switching Regulator
Linear and /or Switching regulators)
Master Power Switch
Yes
Yes
Reset Control
Reset button with MCU and External
Reset button with MCU and External
Reset LED’s
Reset LED’s
USB FTDI Serial Interface
Yes
Yes
CAN Physical Interfaces
2
(routed to 0.1” headers)
2
(routed to 0.1” headers)
LIN Physical Interfaces
2
(routed to Molex headers)
2
(routed to 0.1” headers)
FlexRay Physical Interfaces
2
(routed to 0.1” headers)
2
(routed to 0.1” headers)
Ethernet Physical Interface
1
(MII and RMII Support)
1
(MII only mode)
USB Physical Interface
2
(USB Host and OTG)
1
(USB Host)
MLB Daughter card Connector
Yes
No
SAI Audio / TWRPI Connectors
Yes
No
SDHC Connector
Full Size SDHC Socket
No
Fast External Osc (FXOSC)
Daughter card Crystal * and
40 MHz Crystal
SMA input connector
Slow External Osc (SXOSC)
Daughter card Crystal *
32.768 KHz Crystal
CLKOUT signals available
Yes (GPIO Matrix)
Yes (Standalone pads)
User LEDS
4
4
User Pushbutton Switches
4
2
Hex Encoded Switch
Yes
Yes
Test Potentiometer for ADC
Yes
Yes
GPIO Matrix
All Available Pins not otherwise used
Selection of Pins available from 5
for peripherals
GPIO Ports
Debug
14 Pin JTAG and 50 pin Nexus
14 Pin JTAG
Configuration
Highly configurable via jumper shunts
Fixed (limited configuration via 0 ohm
resistors)
* Daughter card crystals are typically 40 MHz for FXOSC and 32.768 KHz for SXOSC but may
vary between daughter cards.
MPC5748G Low Cost EVB User Guide, Rev. 1, 08/2016
4NXP Semiconductors
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

LCEVB Features
The figure below shows the customer EVB (left) next to the LCEVB (right).
Figure 1. Customer and LCEVB side by side
MPC5748G Low Cost EVB User Guide, User Guide, Rev. 1, 08/2016
NXP Semiconductors
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

3.Configuration Overview
Out of the box, there is no configuration required for the LCEVB to function. Unlike the customer EVB,
the LCEVB is primarily designed for a single mode of operation with no requirement for user
configuration. If you wish to have a more flexible configuration the recommendation is that the fully
configurable customer EVB is purchased.
There are however some jumper footprints and zero ohm resistors populated in positions that would
normally have jumper headers fitted (for example on the MCU power supply lines and tracking to the
peripheral interfaces). If required these can be de-soldered to modify functionality. Any such
modification is done at the full risk of the user and no support or warranty repairs will be provided for a
board that has been modified. Modifications should only be attempted by appropriately trained
personnel using the correct equipment and Personal Protective Apparel
The diagram below gives an overview of the functional blocks of the LCEVB
Figure 2. EVB Functional Blocks
MPC5748G Low Cost EVB User Guide, Rev. 1, 08/2016
6NXP Semiconductors
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Initial Setup
4.Initial Setup
This section details the power, reset, clocks, and debug configuration which is the minimum
configuration needed in order to power ON the LCEVB.
4.1. Power Supply Configuration
The Power supply
section is located in
the bottom left corner
of the LCEVB
The LCEVB requires an external power supply voltage of 5 V DC, minimum 1 A. There is a single 3.3
V switching regulator on the LCEVB providing MCU and peripheral power.
CAUTION
Connecting a power supply with a voltage greater than 5 V will
result in irrecoverable board damage. Check the power supply
voltage before connecting the plug to the LCEVB.
4.1.1.Power Input Connector
Power is supplied to the LCEVB via a 2.1 mm connector from the wall-plug mains adapter as shown
below. Note –if a replacement or alternative adapter is used, care must be taken to ensure the 2.1 mm
plug uses the correct polarization as shown below:
Figure 3. 2.1 mm Power Connector
4.1.2.Power Switch
Slide switch SW2 can be used to isolate the power supply input from the EVB voltage regulators
if required.
Moving the slide switch to the right (away from the power connector) will turn the EVB ON. 

Moving the slide switch to the left (towards the power connector) will turn the EVB OFF. 
MPC5748G Low Cost EVB User Guide, User Guide, Rev. 1, 08/2016
NXP Semiconductors 7
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

4.1.3.Power Status LED
When power is applied to the LCEVB, two green LED’s adjacent to the regulator and power connector
show the presence of the supply voltages as follows:
LED DS5 –Indicates that the 5.0 V supply voltage is present 
LED DS6 –Indicates that the 3.3 V switching regulator is functioning 
If no LED’s are illuminated when power is supplied to the LCEVB and the power switch is in the
“ON” position, the power adapter may be faulty or there may be a fault with the LCEVB. If only one
LED is illuminated there may be a short in that power supply rail –check there is nothing shorting on
the EVB. If you continue to have problems, contact NXP for support.
CAUTION
In the event of a short on the regulator output (in which case one of the
LED’s would be off or dimly illuminated), the regulator and/or the shorted
component will likely be hot.
4.1.4.MCU and Peripheral Voltage Configuration
The following MCU supply rails are connected to the 3.3 V switching regulator:
VDD_HV_ADC0 

VDD_HV_ADC1 

VDD_HV_ADC1_REF 

VDD_HV_A 

VDD_HV_B 

VDD_HV_FLA 

External Ballast Transistor Supply 
Similarly all of the peripheral interfaces (or the I/O power in the peripheral interface) are supplied
from 3.3 V as is the reset circuitry and the voltage sense wire on the JTAG connector.
4.2. Reset Control (SW3)
The reset circuitry is
located in the bottom left
quarter of the LCEVB
next to the power switch
The MCU has a single bi-directional open drain Reset pin. Rather than connect multiple devices to the
reset pin directly, a reset-in and reset-out buffering scheme has been implemented on the LCEVB as
shown in Figure 4. The reset “in” from the reset switch (SW3) and the debug connectors are logically
OR’d together using an AND gate and then connected to the buffer to provide an open-drain output.
The “reset-out” circuitry provides a buffered reset signal that can be used to drive any circuitry
requiring a reset control from the MCU.
MPC5748G Low Cost EVB User Guide, Rev. 1, 08/2016
8NXP Semiconductors
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Initial Setup
This scheme is not required if it is guaranteed that anything driving the reset pin has an open drain
drive and that there is no significant output load on the MCU reset pin.
Figure 4. EVB Reset Control
4.2.1.Reset LEDs
As can be seen above, there are two reset LED’s that can be used to identify the source / cause of a reset:
RED LED DS8 (titled “MCU”) will illuminate if:
The MCU issues a reset (in this condition ONLY this LED will be illuminated and LED
DS1 will be off) 

There is a target reset (i.e. from the reset switch or from the debugger in which case LED
DS1 will be ON) 
YELLOW LED DS7 (titled “EXT”) will illuminate when an external hardware device issues a reset
to the MCU:
The reset switch is pressed 

There is a reset being driven from one of the debug connectors 
Table 2. Reset LED Decoding
LED DS7 (Yellow)
LED DS8 (Red)
Description
OFF
OFF
No Reset being issued from MCU or external logic
OFF
ON
MCU has issued a reset
ON
OFF
External reset issued from switch or debug BUT not being issued to MCU
(check R137 has not been removed)
ON
ON
External reset issued from reset switch or debug and has been issued to MCU.
MPC5748G Low Cost EVB User Guide, User Guide, Rev. 1, 08/2016
NXP Semiconductors 9
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

4.3. MCU Clock Configuration
There is an external 40MHz crystal connected to the MCU Fast External Oscillator (FXOSC)
pins EXTAL and XTAL.
There is also a 32.768 crystal connected to the MCU Slow External Oscillator (SXOSC) pins
OSC32K_EXTAL and OSC32K_XTAL. This can be used for accurate time keeping.
There are 2 pads PG6 and PG7 (located just below the MCU) on the LCEVB to facilitate
measurement of the CLKOUT1 and CLKOUT0 signals.
Note –there is no external clock input on the LCEVB
4.4. Debug Connector (P1)
The JTAG debug
connectors is
located in the top left
corner of the LCEVB
The LCEVB has a single 14-pin keyed JTAG connector for connection to an external debugger.
Before attaching or removing the debug cable from the LCEVB remove power from the EVB to
prevent damage to the LCEVB or debug hardware.
4.4.1.Debug Connector Pinout
The following tables list the pinout for the JTAG connector used on the LCEVB
Table 3. 14-Pin JTAG Debug Connector Pinout
Pin No
Function
Connection
Pin No
Function
Connection
1
TDI
PC0
2
GND
GND
3
TDO
PC1
4
GND
GND
5
TCLK
PH9
6
GND
GND
7
EVTI
PL8
8
N/C
---
9
RESET
JTAG –RSTx
10
TMS
PH10
11
VREF
PER_HVA
12
GND
GND
13
RDY
---
14
JCOMP
10k Pulldown
TDI, TDO and TMS have 10K pullup resistors on the LCEVB. TCLK has a 10K pulldown (R147) to
facilitate STANDBY exit without any additional code (at the sacrifice of slightly higher STANDBY
current), however this can be changed to a pullup if required by removing R147 and fitting the resistor
on R56.
MPC5748G Low Cost EVB User Guide, Rev. 1, 08/2016
10 NXP Semiconductors
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Communications & Memory Interfaces:
Table 4. JTAG Pins Pull State (from MPC5748G Reference Manual)
TERMINAL TYPE
POWERUP pad state
RESET pad status
DEFAULY pad status
RESET
Strong pull-down
Strong pull-down
Weak pull-up
PORST
Weak pull-down
Weak pull-up
Weak pull-up
GPIO
High impedance
High impedance
High impedance
ANALOG
High impedance
High impedance
High impedance
EOUT0, EOUT1
High impedance
High impedance
High impedance
TCK
High impedance
Weak pull-up
Weak pull-up
TMS
High impedance
Weak pull-up
Weak pull-up
TDI
High impedance
Weak pull-up
Weak pull-up
TDO
High impedance
High impedance
High impedance
5.Communications & Memory Interfaces:
This section details the communication interface and storage peripherals that are implemented on
the LCEVB.
5.1. CAN Interfaces (P2, P3)
The CAN circuitry is
located on the top
right edge of the
LCEVB
The LCEVB incorporates two identical CAN interface circuits connected to MCU CAN0 and CAN1
using MC33901 transceivers. Both transceivers are configured for high speed operation by pulling pin
8 to GND via a 4.7 kOhm resistor. There are test points to allow the Select pin to be driven high if
desired. The MC33901 is pin compatible with other CAN transceivers supporting full CAN FD data
rates.
For flexibility, the CAN transceiver I/O is connected to a 0.1” header (P2 for CAN0 / P3 for CAN1)
rather than using non-standard DB9 connectors. The pinout of these headers is shown below.
1
HLGND
Figure 5. CAN Physical Interface Connectors
MPC5748G Low Cost EVB User Guide, User Guide, Rev. 1, 08/2016
NXP Semiconductors 11
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

5.2. LIN Interfaces (P6, P7)
The LIN Physical
interface circuits are
located on the right
edge of the LCEVB
The LCEVB incorporates two LIN transceiver circuits connected to MCU LIN0 and LIN1, using an
NXP MC33662 transceiver. The MPC5748G LIN0 supports both master and slave modes whereas
LIN1 only supports master mode.
On the LCEVB, the LIN0 transceiver is configured as slave mode by default. Master mode operation is
possible by either populating a zero ohm resistor (R143) or buy fitting a jumper header (J2) –see the
schematics for details. The LIN0 transceiver is hard wired for master mode. To save on board space
and cost, both LIN transceivers are connected to 0.1” pitch 3x1 headers as shown below rather than the
usual LIN Molex header.
Figure 6. LIN Physical Interface Connector
Note that in order for the LIN transceiver to function, external 12v must be supplied via pin 2 of the
connector
5.3. USB RS232 Serial Interface (P11)
The USB RS232
interface is on the
left hand edge of the
board (USB Type B
The LCEVB incorporates a USB RS232 serial interface providing RS232 connectivity via a direct USB
connection between the PC and the EVB. The circuit contains an FTDI FT2232D USB to Serial
interface which should automatically install the drivers for two additional COM ports on your PC. Note
that only one of these ports is used so you will need to try both (usually the higher numbered COM port
is the active one). For more information on the USB drivers and general fault finding, consult the FTDI
website at http://www.ftdichip.com/
The MCU LIN2 signals are routed to the FTDI transceiver (UART TX and RX). No handshaking
signals are implemented and no board configuration is required.
5.4. USB HOST Interface (P4)
The USB Host
interface is on the
top left corner of the
LCEVB on the left
The LCEVB includes a Type A (Host) USB interface, routed to a USB type A female connector.
The USB circuit contains a USB83340 transceiver with a MIC2026-1YM USB power switch. There
is no hardware user configuration required to use the USB circuit.
MPC5748G Low Cost EVB User Guide, Rev. 1, 08/2016
12 NXP Semiconductors
GND Vsup LIN
1
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

5.5. Ethernet Interface (P5)
Communications & Memory Interfaces:
The Ethernet
interface is mid-way
along the top edge
of the LCEVB
The EVB incorporates a single DP83848c Ethernet transceiver with the circuitry configured for MII
mode. The transceiver is connected to a pulse J1011F21PNL RJ45 connector which includes a built-in
isolation transformer. There is no hardware configuration needed.
If you require RMII mode or access to both Ethernet ports on the MPC5748G, please purchase
the MPC5748G customer EVB and appropriate daughter cards.
Note that the MCU Ethernet signals are all in the VDD_HV_B domain. The Ethernet PHY will only
function with 3.3 V I/O so if you have made any modifications to the EVB power domain configuration
(via the zero ohm resistors), you need to ensure the VDD_HV_B domain is at 3.3 V before attempting
to use the Ethernet module. If VDD_HV_B is set to 5 V, the signals routed to the Ethernet PHY (see the
EVB schematics) must be left as tristate to prevent damage to the transceiver.
5.6. FlexRay (P8, P9, P10)
The FlexRay
interfaces are midway
down the left hand
edge of the LCEVB
The LCEVB incorporates two FlexRay TJA1080TS/N interfaces connected to MCU FlexRay
channels A and B and routed to two Molex 1.25 mm pitch Pico Blade shrouded headers (standard on
many NXP EVB’s). There is no hardware configuration required to use FlexRay.
Note that the LCEVB is supplied with a 40 MHz crystal by default. If FlexRay is configured to use
the external clock source, then the crystal should be left at 40 MHz
MPC5748G Low Cost EVB User Guide, User Guide, Rev. 1, 08/2016
NXP Semiconductors 13
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

6.User Interface (I/O)
This section details the user I/O available on the LCEVB and includes the GPIO matrix, switches,
LED’s and the ADC variable resistor.
6.1. GPIO Matrix
The GPIO matrix is
on the right hand
edge of the LCEVB
A sub-set of available GPIO pins (available pins being those not already routed to LCEVB peripherals)
are available at the GPIO matrix as detailed below. The matrix provides an easy to follow, intuitive,
space saving grid of 0.1” header through-hole pads. Users can solder wires, fit headers or simply insert a
scope probe into the respective pad.
To use the matrix, simply read the port letter from the top or bottom row of text then the pad number
from the columns on the left or right of the matrix. For example, the 1st pad available on Port B is
PB5 as outlined below.
Figure 7. GPIO Matrix
If a pad is populated in the matrix, it means this is available for exclusive use as GPIO. The exception
to this are the port pins detailed below which are also shared with switches or user LED’s (shaded red in
the matrix diagram above).
PD0, PD1, PD2, PD3 –HEX Encoder Switch
PA1, PA2 –User pushbutton Switches
If you require access to all of the available GPIO pads, the customer EVB and daughter card
provides this additional functionality.
MPC5748G Low Cost EVB User Guide, Rev. 1, 08/2016
14 NXP Semiconductors
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

6.2. User Switches (SW4, SW5)
User Interface (I/O)
The user pushbutton
switches are in the
bottom right corner of
the LCEVB
There are two active high (pulled low, driven to 3.3 V) pushbutton switches on the LCEVB connected
directly to MCU GPIO ports. No configuration is required to use the switches.
SW4 is connected to port PA1 (which is also the NMI pin) and SW5 is connected to port PA2
NOTE
The MCU ports used on the user pushbutton switches are also routed
to the GPIO matrix.
6.3. Hex Encoded Switch (SW1)
The hex encoder
switch is located to
the left of the
GPIO Matrix
There is a single hex encoded 16 position rotary switch on the LCEVB. This outputs a binary
encoded hex value (active high) on four MCU ports (Port D[0..3]).
Table 5. Hex Encoder Switch (SW2)
Position
HEX_SW4
HEX_SW3
HEX_SW2
HEX_SW1
(PD3)
(PD2)
(PD1)
(PD0)
0
0
0
0
0
1
0
0
0
1
2
0
0
1
0
3
0
0
1
1
4
0
1
0
0
5
0
1
0
1
6
0
1
1
0
7
0
1
1
1
8
1
0
0
0
9
1
0
0
1
A
1
0
1
0
B
1
0
1
1
C
1
1
0
0
D
1
1
0
1
E
1
1
1
0
F
1
1
1
1
Note that POSN 0 will ensure that no voltage is applied to the pads. This allows the pads to be used as
normal GPIO (with 10K pulldown) and accessed at the respective pads on the GPIO matrix area.
MPC5748G Low Cost EVB User Guide, User Guide, Rev. 1, 08/2016
NXP Semiconductors 15
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

6.4. User LED’s (DS1, DS2, DS3, DS4)
The user LED’s are
above the user
switches in the lower
right corner
There are four active low user LED’s, DS1 to DS4, connected directly to 4 MCU ports (PG[2..5]) as
shown below. No configuration is required to use the LED’s.
Table 6. Use LED’s (DS1, DS2, DS3 and DS4)
User LED
MCU Pin
DS1
PG2
DS2
PG3
DS3
PG4
DS4
PG5
6.5. ADC Input Potentiometer (RVAR, RV1)
The ADC Pot is
above the hex
switch to the left of
the GPIO matrix
There is a small variable resistor RV1 on the LCEVB which routes a voltage between 0v and 3.3 V to
MCU pin PB4. This is useful for quick ADC testing. Test point RVAR can be used to probe the
voltage with a voltmeter.
Note that this circuit provides a very rough way to evaluate the ADC. There is a small current limiting
series resistor network to limit the injection current to around 4.4 mA.
MPC5748G Low Cost EVB User Guide, Rev. 1, 08/2016
16 NXP Semiconductors
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

MCU Port Pin LCEVB Functions
7.MCU Port Pin LCEVB Functions
The table below shows what each MCU pin is used for on the LCEVB.
Table 7. LCEVB 176QFP Port Pin Functions
No
Port A
Port B
Port C
Port D
Port E
Port F
Port G
Port H
0
GPIO
CAN0
JTAG
GPIO
3
---
GPIO
Ethernet
Ethernet
1
GPIO
2
CAN0
JTAG
GPIO
3
---
GPIO
Ethernet
Ethernet
2
GPIO
2
LIN0
USB1
GPIO
3
FlexRay A
GPIO
GPIO
4,
Ethernet
3
Ethernet
LIN0
USB1
GPIO
3
FlexRay A
GPIO
GPIO
4
---
4
GPIO
ADC Pot
FlexRay B
GPIO
FlexRay B
GPIO
GPIO
4
---
5
GPIO
GPIO
FlexRay A
GPIO
FlexRay B
GPIO
GPIO
4
---
6
GPIO
GPIO
LIN1
GPIO
---
GPIO
GPIO
---
7
Ethernet
GPIO
LIN1
GPIO
---
GPIO
GPIO
---
8
Ethernet
EXTAL32
RS232
GPIO
---
GPIO
---
---
9
Ethernet
XTAL32
RS232
GPIO
---
GPIO
---
JTAG
10
Ethernet
SAI Audio
CAN1
GPIO
---
GPIO
USB1
JTAG
11
Ethernet
GPIO
CAN1
---
GPIO
USB1
USB1
12
GPIO
GPIO
FlexRay
GPIO
Ethernet
GPIO
Ethernet
USB1
13
GPIO
GPIO
FlexRay
GPIO
Ethernet
GPIO
Ethernet
---
14
GPIO
GPIO
FlexRay
GPIO
USB1
Ethernet
USB1
---
15
GPIO
GPIO
FlexRay
GPIO
USB1
Ethernet
USB1
---
No
Port I
Port J
0
GPIO
---
1
GPIO
---
2
GPIO
---
Key:
3
GPIO
---
Pin not bonded out on 176QFP package
4
USB1
---
---
Pin not accessible on LCEVB
5
USB1
6
GPIO
7
USB1
8
GPIO
9
10
11
Ethernet
12
GPIO
13
GPIO
14
GPIO
15
GPIO
2Shared with user switches
3Shared with Hex Encoder Switch
4Shared with user LED’s
MPC5748G Low Cost EVB User Guide, User Guide, Rev. 1, 08/2016
NXP Semiconductors 17
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

8.Appendix
The MPC5748G LCEVB schematics, Rev B are shown below.
MPC5748G Low Cost EVB User Guide, Rev. 1, 08/2016
18 NXP Semiconductors
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

D
C
B
A
5
4
3
2
1
MPC5748G Low Cost Evaluation Board (MPC5748G-LCEVB)
Revision Information
Table Of Contents:
Rev
Date
Designer
Comments
x1
14 Apr 2015
Alasdair Robertson
Start of capture, Working version (256BGA)
D
Power - Main input and 3.3V regulator
Sheet 2
x2
08 May 2015
Alasdair Robertson
Changed to 176 QFP Package and changed periperhal Matrix
Power - MCU Power
Sheet 3
x3
18 May 2015
Alasdair Robertson
Changes required for initial placement
Power - MCU Decoupling
Sheet 4
x4
19 May 2015
Alasdair Robertson
Tidy Up, Replaced some "hard to source" components
Reset and JTAG
Sheet 5
x5
26 May 2015
Alasdair Robertson
Renumber and Back Annoted from Layout
Clocks
Sheet 6
x6
27 May 2015
Alasdair Robertson
Correction to GND on 3v3 Regulator circuit
MCU GPIO 1
Sheet 7
x7
29 May 2015
Alasdair Robertson
Correction to CAN Test points
MCU GPIO 2
Sheet 8
x8
31 May 2015
Alasdair Robertson
Few refdes changes after layout tweaks
Comms1 - CAN and LIN
Sheet 9
x9
01 Jun 2015
Alasdair Robertson
Correction to user LED Refdes after re-number
Comms 2 - FTDI RS232 Interface
Sheet 10
x10
01 Jun 2015
Alasdair Robertson
DNP Jumpers. 0 Ohm resistors added accross LIN jumpers
Comms 3 - USB Host Interface (device footprints only)
Sheet 11
A
11 Jun 2015
Andrew MacDonald
Prototype Manufacture Release
Comms 4 - Ethernet (MII Mode)
Sheet 12
AX1
29 Sep 2015
Alasdair Robertson
Prodn Build changes (LIN0 default to Slave, LIN1 Master only)
Comms 5 - FlexRay
Sheet 13
PN Changed to MPC5748G-LCEVB
C
User - Switches, LED's and Potentiometer
Sheet 14
AX2
26 Oct 2015
Alasdair Robertson
Change to JTAG Pulls to meet latest RM Spec
User - GPIO Pin Matrix
Sheet 15
AX3
29 Oct 2015
Alasdair Robertson
Changed RV1 current limit resistor. SW4 / SW5 refdes swap
AX4
09 Dec 2015
Alasdair Robertson
Pull DOWN on TCLK to mitigate against STANDBY exit issue.
AX5
20 Jan 2016
Alasdair Robertson
Updated NXP Logos
B
12 Feb 2016
Alasdair Robertson
Updated NXP Logos
Caution:
These schematics are provided for reference purposes only.
As such,NXP does not make any warranty, implied or otherwise, as to the
suitability of circuit design or component selection (type or value) used in
these schematics for hardware design using the NXP Calypso family of
B
Microprocessors. Customers using any part of these schematics as a
3 Different test points used in design:
basis for hardware design, do so at their own risk and NXP does not
TPVx - Through Hole Pad small
assume any liability for such a hardware design.
TPHx - Through Hile Pad Large (for standard 0.1" header).
Also
used on IO Matrix (IOMx)
TPX
- Surface Mount Wire Loop
Notes:
- All components and board processes are to be ROHS compliant
- All small capacitors are 0402 unless otherwise stated
- All resistors are 0603 5% 0.1w unless otherwise stated. All zero ohm links are 0603
- All connectors and headers are denoted Px and are 2.54mm pitch unless otherwise stated
Automotive Microcontroller Applications
- All jumpers are denoted Jx. Jumpers are 2mm pitch
East Kilbride, Scotland
- Jumper default positions are shown in the schematics. For 3 way jumpers, default is always posn 1-2.
2 Pin jumpers generally have the "source" on pin 1.
NXP General Business Use
- All switches are denoted SWx
This document contains information proprietary to NXP and shall not be used for engineering design,
A
- All test points (SMT wire loop style) are denoted TPx
without the express written permission of NXP Semiconductors.
- Test point Vias (just through hole pads) are denoted TPVx
procurement or manufacture in whole or in part Freescale AISG Applications, East Kilbride
Signals (ports) have not been routed via busses as this makes it harder to determine where each signal goes.
Designer:
Drawing Title:
A. Robertson
MPC5748G-LCEVB
User notes are given throughtout the schematics.
Drawn by:
Page Title:
A. Robertson
Index and Title Page
Specific PCB LAYOUT notes are detailed in ITALICS
Approved:
Size
Document Number
PDF: SPF-27897
Rev
A. Robertson
B
SCH-27897
B
Date:
Friday, February 12, 2016
Sheet 1of
15
54321
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

5
4
3
2
1
Power Input and Linear Voltage Regulators
Power Supply Input
Power Control
SW2
(Power Switch)
Jumpers can be fitted to
1
3
facilitate power measurements
4
2
2.1mm Barrel
5V0_SR
D
P12 Connector
5V-IN
5
3V3_SR
J3
DNP
1
Main Power In
MCU_3V3
2
C
1
(SR = Swithing Reg)
1
2
MCU_3V3
3
3
C26
D4
C21
HDR 1X2
GND
0.1UF
B340A
10UF
5v0
R142
R48
0
10V
5V0_SR
A
560
J4
DNP
MCU_5V0
C
DS5
A
1
2
MCU_5V0
3
HDR 1X2
GND
LED GREEN
R49
0
5V0_SR
3V3_SR
PER_HVA
3.3v Switching Regulator
R47
0
R45
0
5V0_SR
DNP
U10
PER_HVB
C
8
6
R138
178K
3V3_SR
VIN
PG
R46
0
1
7
1
2
EN
SW
R44
0
3
5
L3
1.0uH
1
DNP
C22
MODE
VOS
R43
2
4
C23
10UF
GND
FB
3v3
270
10V
22UF
9
EP
10V
TPS62082
C
DS6
A
GND
LED GREEN
Inoput Voltage 5V, Output 3.3V at 700mA. Ripple 1.4mV, Approx 90% efficient
B
Test and reference points
GND1 GND2 GND3 GND4
GND15
GND16
1
1
1
1
1
1
GND Test Points,
GND Test Points,
Top Side
underside of board
GND
Automotive Microcontroller
Applications
A
East Kilbride, Scotland
NXP General Business Use
Drawing Title:
MPC5748G-LCEVB
Page Title:
Power Input and Linear Voltage Regulators
Size
Document Number
Rev
B
SCH-27897
PDF: SPF-27897
B
Date:
Friday, February 12, 2016
Sheet 2of
15
D
C
B
A
54321
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.