NXP Semiconductors AN11268 Troubleshooting guide

AN11268
Quick startup guide for POS Development Kit
OM5597/RD2663
Rev. 1.0 — 2 September 2014
242410
Application note
COMPANY PUBLIC
Document information
Info
Content
Keywords
POS, Point of Sales, Development Kit, Reference Design, RC663,
TDA8026
Abstract
This document is intended for new users to start working with the POS
Development Kit. It shows the basic functionality and the implemented
show cases.
Downloaded from Arrow.com.

NXP Semiconductors
AN11268
Quick startup guide for POS Development Kit OM5597/RD2663
AN11268
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2014. All rights reserved.
Application note
COMPANY PUBLIC
Rev. 1.0 — 2 September 2014
242410
2 of 17
Contact information
For more information, please visit:
http://www.nxp.com
For sales office addresses, please send an email to: salesaddress[email protected]
Revision history
Rev
Date
Description
1.0
20140902
Initial version
Downloaded from Arrow.com.Downloaded from Arrow.com.

NXP Semiconductors
AN11268
Quick startup guide for POS Development Kit OM5597/RD2663
AN11268
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2014. All rights reserved.
Application note
COMPANY PUBLIC
Rev. 1.0 — 2 September 2014
242410
3 of 17
1. Introduction
1.1 Scope
The purpose of this document is to provide a guideline to aid in the first operation of the
OM5597 RD2663 Point of Sales Development Kit (further referenced to as POS DK).
1.2 General Description
The POS DK can be used to demonstrate, evaluate and adapt the simple implementation
of NXP’s devices in Point of Sales terminals.
Both contactless and contact applications can easily be evaluated. This development kit
is EMV level1 digital and analog certified and therefore an ideal starting point to develop
specific POS terminals based on NXP components.
The design embeds all the required hardware and software for the following interfaces:
•EMVCo compliant contactless smart cards based on RC663,
•EMVCo compliant contact smart cards based on TDA8026,
•Up to four secure access modules (SAMs) via TDA8026.
The user interface is composed of a color LCD display and a pin pad.
The default hardware interface is RS-232, which is used for code uploading and
debugging. However, a USB 2.0 full speed connector is also offered but not implemented
in the default software.
1.3 Package Content
The OM5597/RD2663 POS Development Kit comes in a package containing the
following items:
1. POS DK including firmware
2. USB cable
3. MIFARE DESFire EV1 card [8]
4. Personalized JCOP dual-interface payment card [10]
A SAM is not part of this kit and must be ordered separately.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

NXP Semiconductors
AN11268
Quick startup guide for POS Development Kit OM5597/RD2663
AN11268
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2014. All rights reserved.
Application note
COMPANY PUBLIC
Rev. 1.0 — 2 September 2014
242410
4 of 17
2. Getting Started
2.1 Powering the POS DK
The POS DK requires a power supply between UDCmin = 4.7 and UDCmax = 5.3 V. This can
be provided in two ways:
•Use the USB connector to connect e.g. to a PC (only power-supply, no data
connection implemented)
•Use the 2.5mm jack with external power supply.
Do not supply the POS DK with a voltage higher than 5.3 V as it can potentially damage
the POS DK. A supply voltage below 4.7 V might lead to improper functionality.
For details about the power-supply please refer to AN11270 “Hardware Design Guide for
POS Development Kit”.
The power consumption of the POS DK can reach up to 250-300 mA when generating
the RF field.
Once powered on, the POS DK displays a welcome message as shown in Fig 1.
Fig 1. Welcome Message
As soon as a key is pressed the main menu will be displayed as shown in Fig 2.
The items at the menu and the consequent items in the sub-menus can be accessed by
pressing the relevant key at the pin pad.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

NXP Semiconductors
AN11268
Quick startup guide for POS Development Kit OM5597/RD2663
AN11268
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2014. All rights reserved.
Application note
COMPANY PUBLIC
Rev. 1.0 — 2 September 2014
242410
5 of 17
Fig 2. Info Menu
2.2 Showcases
The POS DK comes with a number of showcases which allow an easy demonstration of
its capabilities and features:
1. Showcase “Payment”
2. Showcase “Closed Loop Payment”
3. Showcase “Payment System Environment”
4. Showcase “P2P Communication”
In order to leave a showcase during processing (e.g. during card polling), just press the
button ‘#’. This will cancel the current step and go back to the main menu.
2.2.1 Payment
For demonstrating the Payment showcase you need the MIFARE DESFire Card,
included in the POS package. Please note that this case does not show any secure
communication.
First the card has to be initialized with the according payment application as well as an
initial credit:
1. Power on the POS DK.
2. Press any key. The INFO menu appears.
3. Press key ‘2’ to select the INFORMATION sub-menu as seen in Fig 3.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

NXP Semiconductors
AN11268
Quick startup guide for POS Development Kit OM5597/RD2663
AN11268
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2014. All rights reserved.
Application note
COMPANY PUBLIC
Rev. 1.0 — 2 September 2014
242410
6 of 17
Fig 3. Information menu
4. Press key ‘3’ to select the RESET CARD sub-menu. ‘Present card’ is displayed
5. Put the MIFARE DESFire card on the antenna of the reader in order to create a
payment application on the card. By doing this an initial amount of 500.00 credits
is also stored on the card which can be consumed during the payment
showcase. After this procedure the message “RESET SUCCESS” is displayed
as shown in Fig 4.
Fig 4. Reset Successful
This procedure can be repeated at any time to reset the amount of credits to 500.00. By
pressing any key, the main menu will be shown again.
Now the actual payment showcase can be shown:
1. Press key ‘1’ to start the payment application as shown in Fig 5.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

NXP Semiconductors
AN11268
Quick startup guide for POS Development Kit OM5597/RD2663
AN11268
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2014. All rights reserved.
Application note
COMPANY PUBLIC
Rev. 1.0 — 2 September 2014
242410
7 of 17
Fig 5. Payment Application Screen
2. Now enter the amount which shall be debited from the card and confirm with ‘*’.
3. Put the card on the antenna of the reader.
If “DEBIT SUCCESS” is displayed as shown in Fig 6, the previously inserted
amount is debited from the credits on the card.
If “DEBIT ERROR” is displayed the entered value was higher than the amount of
credits on the card.
4. By pressing any key, the main menu will be shown again.
The remaining amount stored on the card can be checked by following procedure:
1. Press key ‘2’ to select the INFORMATION sub-menu.
2. Press key ‘2’ to select the CARD INFO sub-menu.
3. Put the MIFARE DESFire Card on the antenna of the reader. As shown in Fig 7
‘NXP DESFire NoAuth’ and the remaining value is now displayed.
Fig 6. Payment successful
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

NXP Semiconductors
AN11268
Quick startup guide for POS Development Kit OM5597/RD2663
AN11268
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2014. All rights reserved.
Application note
COMPANY PUBLIC
Rev. 1.0 — 2 September 2014
242410
8 of 17
Fig 7. Payment Card Info without Authentication
2.2.2 Closed Loop Payment
For demonstrating the Closed Loop Payment showcase you need the MIFARE DESFire
Card, included in the POS package, as well as a MIFARE SAM V2.6 [12] which is
available separately.
This showcase has a similar workflow as described in section 2.2.1 but this time the
communication is secured by the SAM.
Therefore plug in the SAM into one of the SAM Slots and power up or reset the reader.
Then proceed as described in section 2.2.1.
During the reset of the card, an application with restricted access rights is stored on the
card. When calling the CARD INFO sub-menu the text “NXP DESFire Auth” is displayed
as shown in Fig 8.
Fig 8. Payment Card Info with Authentication by SAM
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

NXP Semiconductors
AN11268
Quick startup guide for POS Development Kit OM5597/RD2663
AN11268
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2014. All rights reserved.
Application note
COMPANY PUBLIC
Rev. 1.0 — 2 September 2014
242410
9 of 17
2.2.3 Payment System Environment
This showcase demonstrates how to read out basic information from one of the cards
provided with this development kit (MIFARE DESFire EV1 and JCOP dual-interface)
1. Power on the POS DK
2. Press any key. The INFO menu appears
3. Press key ‘2’ to select the INFORMATION sub-menu
4. Press key ‘2’ to select the CARD INFO sub-menu. As shown in Fig 9 you are
asked to present the card.
Fig 9. Present card
5. Put either one of the cards on the antenna of the contactless reader or put the
JCOP card in contact reader. In the second case consider the correct orientation
of the card: contact-interfaces to the front and upside
6. You can ether present the card to the antenna of the reader or put it into the card
slot. In the second case please keep in mind the slot in direction. (Chip
connector first and up)
The display now shows the name of the detected application. In this case it is ‘POS RD
Banking Card’ as seen in Fig 10.
Fig 10. Application Identifier
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

NXP Semiconductors
AN11268
Quick startup guide for POS Development Kit OM5597/RD2663
AN11268
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2014. All rights reserved.
Application note
COMPANY PUBLIC
Rev. 1.0 — 2 September 2014
242410
10 of 17
2.2.4 P2P Communication
This showcase demonstrates how to perform peer-to-peer communication with an NFC
enabled mobile phone. This can be used for couponing applications, for example.
1. In case a NFC mobile phone with Android 2.3 is used, it is required to start an
application and share a tag application. Give also a name for this tag e.g. “My
NFC tag”.
2. Power on the POS DK.
3. Press any key. The INFO menu appears.
4. Press key ‘2’ to select the INFORMATION sub-menu.
5. Press key ‘2’ again to reach the CARD INFO Sub-menu.
6. The message ‘Present card’ is displayed. The POS DK now tries to detect a tag
in the field.
7. Put the mobile phone over the antenna of the POS DK
8. A peer-to-peer communication is performed between the POS DK and the
mobile phone.
9. Once the communication is performed, the POS DK displays the message: ‘NFC
mobile detected’. At the mobile phone, the message ‘New tag collected’, ‘NXP
POS Reference Design Payment Coupon ID’ is displayed.
2.3 Using the POS DK as a Reference Design
2.3.1 Hardware Design
All schematics, Layouts (Gerber files) and the BOM of the POS DK hardware are
provided in the source package as well.
For more information on the hardware please refer to the Hardware Design Guide
AN11270 [1].
2.3.2 Software Design
The software stack, running on the POS DK including the previously described
showcases is available in source and binary in the source package to allow an easy
adoption to the individual design of the costumer.
For more information on the software please refer to the Software Design Guide
AN11269 [3].
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.