NXP Semiconductors S32G-VNP-EVB3 User manual

Part Number Here
Quick Start Guide
S32G is a vehicle network processor delivering high levels of real-time and
applications processing, supporting CAN/LIN/FlexRay networking and
Gigabit Ethernet interfaces with hardware acceleration and delivering a high
level of embedded security and ASIL D functional safety capabilities.
S32G-VNP-EVB3
S32G-VNP-EVB3

1
Quick Start Guide
Figure 1: S32G-VNP-EVB3
S32G-VNP-EVB3
The NXP S32G-VNP-EVB3 supports development, evaluation and
demonstrations with the NXP S32G2x and S32G3x Vehicle Network
Processor (VNP).
S32G targets applications such as:
• Central gateways and domain controllers
• Firmware Over-The-Air (FOTA) updates
• Secure key management, Smart antennas
• High-performance central compute nodes
GET TO KNOW THE S32G-VNP-EVB3

2
Quick Start Guide
Figure 2: S32G-PROCEVB3-S Processor Module
GET TO KNOW THE S32G-PROCESSOR MODULE

3
Quick Start Guide
Figure 3 : S32G-VNP-EVB3 Block Diagram
S32G-VNP-EVB3 Block Diagram

4
Quick Start Guide
Install S32G and Heatsink
When the S32G-PROCEVB3-S is stacked
on the S32GRV-PLATEVB: Jumper J96 on
the S32G-PROCEVB3-S should be in position
1-2, and only the S32GRV-PLATEVB needs
to be powered. Connect power supply to the
12V power jack P3 on S32GRV-PLATEVB.
When the S32G-PROCEVB3-S is used
standalone: Jumper 96 should be in position
2-3. Connect power supply to the 12V power
jack P1 on S32G-PROCEVB3-S.
Connect the Power Supply
1
2
Install Software
Setup Tera Term Console
3
4
Follow the instructions in the S32G-
PROCEVB3-S –Silicon mounting guide to
install the S32Gand heat sink.
For fan usage instructions refer to the
S32G3-VNP-EVB User Guide
Open Tera Term on Windows PC. Select
the serial port to which the micro–USB J58
of the S32G-PROCEVB3-S is connected
and click OK.Go to Setup→ Serial Port
and select 115200 as the baud rate.
Install the following….
✓Tera Term for console
✓FTDI CDM v2.12.28 WHQL driver for
serial configuration.
✓Win32 Disk Imager
✓Packet Sender Application
STEP-BY-STEP INSTRUCTIONS
Power ON the S32G-VNP-
EVB3
5
Switch ON the power switch SW1on the
S32GRV-PLATEVB and power switch SW10
on the S32G-PROCEVB3-S.
Diagnostics Utility
6
The Diagnostics Utility is auto executed from
the SD card. Console display on Tera Term
shows the status of the diagnostic tests.

5
Quick Start Guide
•DocStore
oS32G-PROCEVB3-S –Silicon mounting guide
oS32G-PROCEVB3-S-Rev A-Schematics-Layout
oS32G3 Hardware Design Guide
oS32G3 Boot Process Application Note
oS32G3-VNP-EVB User Guide
•NXP web
oS32 VNP EVB Platform Board design details
•Flexera
oSW32G_EVBDIAG_0.8.7 Board Diagnostics
Useful Documents and Projects

www.nxp.com
NXP and the NXP logo are trademarks of NXP B.V. All other product or service names are the property of their
respective owners. © 2021 NXP B.V.
SUPPORT
Visit www.nxp.com/support for a list of
phonenumbers within your region.
WARRANTY
Visit www.nxp.com/warranty for complete
warranty information.
Get Started
Download installation software
and documentation under
“Jump Start Your Design” at
nxp.com/XXXXXXXXX.
Document Number: S32G-VNP-EVB3QSG REV 0