Odyssey BLAZIN’ MOTO User manual

LiPo Battery
On/Off
Switch
Battery Connector
1
INSTRUCTION MANUAL: BLAZIN’ MOTO 8+
SETTING UP BLAZIN’ MOTO
1. Turn off the power switch.
2. Turn the battery cover knob to open compartment.
3. Connect the battery wire to the Blazin’ Moto’s connector as shown on the diagram.
4. Close the battery compartment and switch the power switch to On.
FOR
AGES

Demo
Transform
On/Off
Switch
Move Forward
Move Backward Turn Left
Command Speaker
Turn Right
LED
Indicator
USB Charging Cord
Robot
LiPo
Battery
3x AA Batteries
2
SETTING UP THE REMOTE CONTROL
CHARGING THE BLAZIN’ MOTO’S BATTERY
OPERATING BLAZIN’ MOTO
1. Turn the battery cover knob to open the
compartment.
2. Install 3x new AA batteries taking care to
match the correct polarity (+/-).
3. Close the cover and turn the cover knob
to lock the cover in place.
- For best results the car needs to be within a 15’ foot range of the controller.
- For effective voice commands make sure you are within 12 inches of the
controller command speaker.
- If left unattended the car will go into power saving mode after 5 minutes. To
wake, press any button on the controller.
- If the sound becomes intermittent this indicates low battery. Please follow the
battery charging instructions to recharge.
Tip. Full charge takes approx. 1hr
1. Remove the battery from the robot as
shown in the robot setting up
instructions.
2. Connect the robot battery to the USB
charging cord connector.
3. Plug the USB cord into a 5v1a USB charger.
4. The charger light will turn on to indicate charging. When the charger light
goes out charging is complete and you can reinstall the battery in the robot.
Controller Functions

I am powerful and I am
the peace envoy of the
Earth, let us go to battle
for the Earth peace.
Transform
and roll out.
3
To transform from truck to robot, either speak “transform” into the voice command speaker or press the
“transform button”.
To make the car drift or the robot dance, either speak “drift” or “dance” into the voice command
speaker, or press the “Demo Button”.
Truck & Robot Movement
Drift & Dance Mode
Transforming from Truck to Robot
Press the forward
button or speak
“FORWARD” into the
voice command
speaker and the
truck/robot will move
forward.
Press the backward
button or speak
“BACKWARD” into
the voice command
speaker and the
truck/robot will move
backward.
Press the turn left
button or speak
“TURN LEFT” into the
voice command
speaker and the
truck/robot will turn
left.
Press the turn right
button or speak
“TURN RIGHT” into the
voice command
speaker and the
truck/robot will turn
right.

4
CARE & MAINTENANCE
CAUTIONS & WARNINGS
•Suitable for ages 8 and up. Adult supervision is always recommended.
•This product contains small parts which are a choking hazard. Keep
away from small children.
•Manufacturers and dealers disclaim all responsibility for damage caused
by misuse.
•Keep hair and loose clothing away from the Blazin’ Moto when powered
on.
•If Blazin’ Moto will be stored and unused for an extended period of time,
please remove the batteries.
•Check the batteries regularly for potential leakage or corrosion that may
occur.
• When installing the batteries carefully follow the polarity marking +/-.
•Do not mix different battery types.
•Remove exhausted or drained batteries.
•Do not exceed charging volts and amps of 5v1a.
•Do not leave charger connected or charge for more than 1hr.
• Do not submerge the unit in any liquids.
• Keep the unit dry.
•Do not place the unit near powerful, un-shielded magnets.
•Do not expose the unit to extreme hot or cold temperatures.
•Do not hit, drop, or smash the unit with extreme force.
•Do not disassemble the unit for any reason.
NOT FOLLOWING THESE PRECAUTIONS WILL VOID YOUR WARRANTY.
For Customer Service please email:
[e-mail]
Please note the units model number and name in your email:
Model no. ODY-1052 •Blazin’ Moto
www.OdysseyToys.com