OEM Tools 24993 Service manual

UNPACKING
After unpacking the OEMTOOLS™Workshop Creeper Seat,
inspect carefully for any damage that may have occurred
during transit. Check for loose, missing, or damaged parts.
If any damage is observed, a shipping damage claim must
be filed with carrier. DO NOT use Creeper Seat if broken,
bent, cracked or damaged parts (including labels) are
noted. Any Creeper Seat that appears damaged in any
way, operates abnormally or is missing parts should be
removed from service immediately. If you suspect that the
Creeper Seat was subjected to a shock load (a load that
was dropped suddenly, unexpectedly, etc.), immediately
discontinue use until it has been checked by a factory
authorized service center.
Please read and save these instructions. Read through this owner’s manual carefully before using product. Protect yourself and
others by observing all safety information, warnings, and cautions. Failure to comply with instructions could result in personal
injury and/or damage to product or property. Please retain instructions for future reference.
The following safety information is provided as a guideline to help you operate your product under the safest possible conditions.
Any tool or piece of equipment can be potentially dangerous to use when safety or safe handling instructions are not known or
not followed. The following safety instructions are to provide the user with the information necessary for safe use and operation.
Please read and retain these instructions for the continued safe use of your product. Failure to follow instructions listed below
may result in serious injury. In addition, make certain that anyone who uses the equipment understands and follows these
safety instructions as well.
Operating Instructions and Parts Manual 24993/24994/24995/24996/24997/24998/24999
FOR CUSTOMER SERVICE
Technical Question?
CALL 1-866-458-2472
[email protected]
Thank you very much for choosing an OEMTOOLS™Product!
For future reference, please register your new tool at www.oem-tools.com and complete the owner’s record below:
Model: _______________ Purchase Date: ___________
Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product
before you begin using it. This product is designed for certain applications only. OEMTOOLS™cannot be responsible for issues
arising from modification. We strongly recommend this product is not modified and/or used for any application other than that for
which it was designed. If you have any questions relative to a particular application, DO NOT use the product until you have first
contacted customer service to determine if it can or should be performed on the product.
Explanation of Safety Signal Words
WARNING:Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION:Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
CAUTION:Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may
result in property damage.
NOTES:Provide clarity and helpful information.
WORKSHOP
CREEPER SEAT
1
7/18
2018 OEMTOOLS™
WARNING
24993 - Green
24994 - Black
24995 - White
24996 - Blue
24997 - Orange
24998 - Red
24999 - Yellow

2
Operating Instructions and Parts Manual 24993/24994/24995/24996/24997/24998/24999
7/18
2018 OEMTOOLS™
WORKSHOP
CREEPER SEAT
IMPORTANT INSTRUCTIONS
AND SAFETY RULES
1. Know your product. Read this manual carefully. Learn
the product’s applications and limitations, as well as
potential hazards specific to it.
2. Keep work area clean and well lit. Cluttered or dark
work areas invite accidents.
3. Keep children away. All children should be kept
away from the work area. Never let a child handle
this product.
4. DO NOT operate this product if under the influence of
alcohol or drugs. Read warning labels on prescriptions
to determine if your judgment or reflexes are impaired
while taking drugs. If there is any doubt, DO NOT
attempt to operate.
5. Use safety equipment. Eye protection should be worn at
all times when operating this product. Use ANSI approved
safety glasses. Everyday eyeglasses are NOT safety glasses.
Dust mask, non-skid safety shoes, hard hat or hearing
protection should be used in appropriate conditions.
6. Wear proper apparel. Loose clothing, gloves, neck-ties,
rings, bracelets or other jewelry may present a potential
hazard when operating this product. Keep all apparel
clear of the product.
7. DO NOT overreach. Keep proper footing and balance
at all times when operating this product.
8. Check for damage. Check your product regularly. If
part of the product is damaged, it should be carefully
inspected to make sure that it can perform its intended
function correctly. If in doubt, the part should be
repaired. Refer all servicing to a qualified technician.
Consult your dealer for advice.
9. Keep away from flammables. DO NOT attempt to
operate this product near flammable materials or
combustibles. Failure to comply may cause serious
injury or death.
10. Store idle product out of the reach of children and
untrained persons. This product may be dangerous in
the hands of untrained users.
11. Maintain product with care.
12. Keep product dry and clean.
13. DO NOT use a damaged product. Tag damaged
products “DO NOT USE” until repaired.
14. Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the product’s operation.
15. Use only accessories that are recommended by the
manufacturer for your model. Accessories that may be
suitable for one product may become hazardous when
used on another product.
16.If damaged, have the product serviced before
using. Many accidents are caused by poorly
maintained products.
17. Product service must be performed only by qualified
repair personnel. Service or maintenance performed by
unqualified personnel could result in a risk of injury.
18. When servicing a product, use only identical replacement
parts. Use of unauthorized parts or failure to follow
maintenance instructions may create a risk of injury.
19. Maintain a safe working environment. Keep the work
area well lit. Make sure there is adequate surrounding
workspace. Keep the work area free of obstructions,
grease, oil, trash, and other debris. DO NOT use this
product in a damp or wet location.
20. Maintain labels and nameplates on this product. These
carry important information. If unreadable or missing,
contact OEMTOOLS™for a replacement.
21. Avoid accidental fire and/or explosion. DO NOT smoke
near engine fuel and battery components.
22. We believe the information contained herein to be
reliable. However, general technical information is given
by us without charge and the user shall employ such
information at their own discretion and risk. We assume
no responsibility for results or damages incurred from
the use of such information in whole or in part. Always
refer to specific instructions and technical information
supplied by the vehicle manufacturer.
SPECIFIC SAFETY INSTRUCTIONS
AND WARNINGS
23. The OEMTOOLS™Workshop Creeper Seat is
specifically designed to be used as a mobile workshop/
garage/shed seat ONLY and is not designed for any
other purpose. Using the Workshop Creeper Seat for
any other purpose could be dangerous and could
cause serious injury/death to yourself and others.
24. NEVER stand on, lie on or operate the Workshop
Creeper seat at any speed, on rough/exposed
uneven surfaces.
25. DO NOT stand on this product. You may fall, which
may lead to personal injury.
26.DO NOT let children near the Workshop Creeper
Seat. DO NOT allow children to play on, stand
upon or climb on seat.
27. Always distribute objects in/on the Workshop Creeper
Seat evenly. Uneven weight distribution may cause the
seat to tip over.
28. DO NOT step or lean on the drawers.
29.DO NOT alter this product in any way. Any added
material or components may imbalance the
product, which may lead to property damage and
personal injury.
30. Be mindful of sharp edges/welds while assembling and
operating this product. Always wear safety gloves and
appropriate safety equipment while working with tools
and equipment.
31. DO NOT exceed weight capacity (see product
specifications). This may lead to product failure and
personal injury.
32. Keep this product on a flat, level surface. Failure to do
so may cause the product to tip and lead to property
damage and personal injury. It is easy to lose control of
the Workshop Creeper Seat if attempting to pull a load
on an uneven or sloped surface.
33. Beware of imperfections and cracks on the work floor.
34. Should the equipment be used in a manner not
specified, the protection provided by the equipment
may be impaired and the warranty voided.

3
Operating Instructions and Parts Manual 24993/24994/24995/24996/24997/24998/24999
7/18
2018 OEMTOOLS™
WORKSHOP
CREEPER SEAT
NOTE: The manufacturer declines any and all
responsibility for damage to vehicles or components if
said damage is the result of unskillful handling by the
operator or of failure to observe the basic safety rules set
forth in the instruction manual.
WARNING:Read Rules for Safe Operation and
Instructions carefully.
IMPORTANT SAFETY INSTRUCTIONS
The warnings, precautions, and instructions discussed
in this manual cannot cover all possible conditions
and situations that may occur. The operator must
understand that common sense and caution are factors
which cannot be built into this product but must be
supplied by the operator.
PURPOSE
The OEMTOOLS™Workshop Creeper Seat is a fully
functioning seat with 2 tool tray drawers allowing you to
keep everything you need close at hand. Keep your drink
or spray cans close by in the 3 can holder. Four swivel
wheels roll smoothly across the floor with easy turning for
optimum maneuverability.
PRODUCT SPECIFICATIONS
Weight Capacity: 286 Lbs.
Product Weight: 17.6 Lbs.
Tool Drawer Max Weight: 66 Lbs.
Product Dimensions: 11.76" x 11.76" x 16.68"
Construction: Heavy Gauge Steel
CONTENTS
Vinyl Padded Seat (1), Nut & Bolt Drawer (1), Tool Drawer (1),
Support Legs (4), Castors (4), Under Seat Storage Base (1),
Can Holder (1) and Fastener Pack (1).
ASSEMBLY
The OEMTOOLS™Workshop Creeper Seat comes packed
flat and requires assembly. Follow the instructions below
to assemble your OEMTOOLS™Workshop Creeper Seat.
1. Lay out all the contents and ensure there are no
missing/damaged parts (Fig. 1).
2. Lay the Vinyl Padded Seat (1) on a clean flat surface,
with the drawers (2 & 3) facing up (Fig. 2).
3. Using one of the Support Legs (4), align the 4 holes
in the Support Leg with the holes of the Vinyl Padded
Seat (1). Insert the supplied bolts, lock washers and flat
washers and hand tighten (Fig. 3).
4. Assemble the remaining three Support Legs (4) to the
Vinyl Padded Seat (1). Hand tighten the bolts (leave all
bolts loose until completely assembled) (Fig. 4).
5. Turn over the Under Seat Storage (6) so the storage
cavity is facing the floor (Fig. 5) and align the holes with
the thread on the Support Legs (4) (Fig. 6).
6. Assemble the Under Seat Storage (6) to the Support
Legs (4) with the supplied bolts, lock washers and flat
washers; hand tighten only (Fig. 7).
Figure 1
Figure 5
Figure 2
Figure 4
Figure 6
Figure 7
Figure 3

4
Operating Instructions and Parts Manual 24993/24994/24995/24996/24997/24998/24999
7/18
2018 OEMTOOLS™
WORKSHOP
CREEPER SEAT
7. Align a Castor (5) with the threads located on the
bottom of the Under Seat Storage (6). Using the
supplied 4 mm Hex Key, assemble the Castors with the
supplied bolts, lock washers and flat washers. Repeat
for all Castors (Fig. 8).
8. Assemble the Can Holder (7) on an opposite side of
one of the drawers. Remove the 4 bolts previously
installed (Fig. 9) and align the can holder to the side of
the Workshop Creeper Seat.
9. Reinstall the 4 bolts, lock washers and flat washers
removed in the previous step. Secure the Can Holder
(7) to the Workshop Creeper Seat (Fig. 10).
10. Turn the Workshop Creeper Seat over onto its wheels to
ensure everything is correctly aligned. Tighten all bolts
using the supplied 4 mm Hex Key (Fig. 11).
11. Your Workshop Creeper Seat is now ready for use.
Periodically check to ensure all bolts are tight on your
Workshop Creeper Seat.
MAINTENANCE AND STORAGE
The OEMTOOLS™Workshop Creeper Seat should be stored
in a cool and dry area and out of the reach of children.
1. Very little maintenance is required for this product.
Wipe clean as needed; only use a mild soap to clean,
and dry immediately upon cleaning.
2. Periodically check to ensure all fasteners are tightened
properly.
DISPOSAL
At the end of the useful life of the product, dispose of
the components according to all state, federal and local
regulations.
Figure 9
Figure 8
Figure 11
Figure 12
Figure 10

5
Operating Instructions and Parts Manual 24993/24994/24995/24996/24997/24998/24999
7/18
2018 OEMTOOLS™
WORKSHOP
CREEPER SEAT
Figure Description Qty.
1 Vinyl Padded Seat 1
2 Pull Out Drawer 1
3 Ball Bearing Slide Drawer 1
4 Support Legs 4
5 Castors 4
6 Under Seat Storage 1
7 Can Holder 1
8 Fastener Pack (Not Shown) 1
PARTS DESCRIPTION NOTE: Not all components of the product are
replacement items but are illustrated as a convenient
reference for location and position in the assembly
sequence.
OEMTOOLS™and/or its distributors have provided the
parts list and assembly diagram as a reference only.
Neither OEMTOOLS™nor its distributors make any
representation or warranty of any kind to the buyer and/
or user of this tool that he or she is qualified to do any
repairs or replace any parts of this product. OEMTOOLS™
and its distributors expressly state that all repairs or parts
replacement should be done by certified or licensed
technicians. The buyer assumes all risk and liability
arising out of his or her repairs or parts replacement to
the original production.
PARTS LIST AND DIAGRAM
1
7
2
3
4
5
6

6
Operating Instructions and Parts Manual 24993/24994/24995/24996/24997/24998/24999
7/18
2018 OEMTOOLS™
WORKSHOP
CREEPER SEAT
NOTES:

7
Operating Instructions and Parts Manual 24993/24994/24995/24996/24997/24998/24999
7/18
2018 OEMTOOLS™
WORKSHOP
CREEPER SEAT
NOTES:

8
Operating Instructions and Parts Manual 24993/24994/24995/24996/24997/24998/24999
7/18
2018 OEMTOOLS™
WORKSHOP
CREEPER SEAT
CONTACT US
3580 E. Raines Road, Suite 3, Memphis, TN 38118
Tel: [phone]
www.oem-tools.com
OEMTOOLS™ONE YEAR WARRANTY
For up to one year from the date of purchase of this OEMTOOLS™product, if you find any defect in material or
workmanship (through normal usage), return it to the place of purchase or to OEMTOOLS™for repair or replacement at
our discretion. In order to obtain this service, send the product and proof of purchase (transportation pre-paid) to:
OEMTOOLS™Q.A. Dept, 3580 E. Raines Road #3, Memphis, TN 38118.
We will not be responsible for lost or damaged goods during transportation; please insure your package. If our
inspection verifies the defect, we will either repair or replace the product, or we may elect to refund the purchase price
if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if
we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you
must bear the cost of returning the product.
OEMTOOLS™does not provide warranty for products labeled other than OEM®or OEMTOOLS™. OEMTOOLS™will
not provide any warranty for products subjected to abnormal use. Abnormal use includes (but is not limited to) abuse,
accident, alteration, neglect, and unauthorized or unreasonable use or repairs. This warranty does not cover bits,
blades, files, batteries, or calibration. We recommend that you maintain your tools and sharpen or replace blades, bits,
files, and batteries as necessary. OEMTOOLS™reserves the right to make any changes in construction or design at
any time without any obligation in incorporating such changes to tools or equipment previously sold.
OEMTOOLS™makes every effort to ensure that its products meet high quality and durability standards, and warrants
to the original purchaser that this product is free from defects in materials and workmanship for the period of one
year from the date of purchase. This warranty does not apply to damage due directly or indirectly to misuse, abuse,
negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear
and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or
consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY
IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS. This warranty gives you specific legal rights, and you may also have other rights,
which vary from state to state.
Don’t forget to register your new OEMTOOLS™product at www.oem-tools.com.