OEM Tools OEM24615 User manual

WARNING
The following safety information is provided as a guideline to help you operate your Tool Cabinet under the safest possible conditions. Any
tool or piece of equipment can be potentially dangerous to use when safety or safe handling instructions are not known or not followed. The
following safety instructions are to provide the user with the information necessary for safe use and operation. Please read and retain these
instructions for the continued safe use of your Tool Cabinet. Failure to follow instructions listed below may result in serious injury. In addition,
make certain that anyone who uses the equipment understands and follows these safety instructions as well.
Explanation of Safety Signal Words
WARNING:Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION:Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
CAUTION:Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may
result in property damage.
NOTES:Provide clarity and helpful information.
Thank you very much for choosing an OEMTOOLS®Product!
For future reference, please register your new tool at www.oem-tools.com and complete the owner’s record below:
Model: _______________ Purchase Date: ___________
Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product before you begin
using it. This product is designed for certain applications only. OEMTOOLS®cannot be responsible for issues arising from modification. We strongly
recommend that this product is not modified and/or used for any application other than that for which it was designed. If you have any questions relative
to a particular application, DO NOT use the product until you have first contacted customer service to determine if it can or should be performed on the
product.
WARNING:Pursuant to California Proposition 65, this product contains chemicals known to the state of California to cause cancer and birth
defects or other reproductive harm. Wash hands after handling.
Operating Instructions and Parts Manual OEM24615
Please read and save these instructions. Read through this owner’s manual carefully before using product. Protect yourself and others by observing
all safety information, warnings, and cautions. Failure to comply with instructions could result in personal injury and/or damage to product or property.
Please retain instructions for future reference.
1
8/20
2020 OEMTOOLS®
72" 11 DRAWER CABINET AND
UPPER CABINET - STAINLESS STEEL
FOR CUSTOMER SERVICE
Technical Question?
CALL 1-866-458-2472
[email protected]
UNPACKING
After unpacking the unit, inspect carefully for any damage that may
have occurred during transit. Check for loose, missing, or damaged
parts. If any damage is observed, a shipping damage claim must be
filed with the carrier. DO NOT use the OEMTOOLS®72" 11 Drawer
Cabinet and Upper Cabinet - Stainless Steel if broken, bent, cracked
or damaged parts (including labels) are noted. Any Tool Cabinet that
appears damaged in any way, operates abnormally or is missing parts
should be removed from service immediately. If you suspect that the
Tool Cabinet was subjected to shock load (a load that was dropped
suddenly, unexpectedly, etc.) immediately discontinue use until it has
been checked by a factory authorized service center.

2
Operating Instructions and Parts Manual OEM24615
8/20
2020 OEMTOOLS®
72" 11 DRAWER CABINET AND
UPPER CABINET - STAINLESS STEEL
IMPORTANT INSTRUCTIONS
AND SAFETY RULES
1. The maximum product weight, including contents, for this unit
should be no more than 1600 Lb. (726 kg).
2. The maximum weight for each drawer should be no more than 100
Lb. (45 kg).
3. Do not attempt to lift the cabinet using chains, ropes or lifting
devices, if two people cannot lift the cabinet by the side handles.
Use a forklift placed under the bottom of the cabinet if this situation
occurs. The side handle may fail, which may cause personal injury
or damage to the product.
4. Close the doors and lock the drawers before moving this product.
The drawers could come open and make the product unstable and
tip, which may cause personal injury or product damage.
5. BE CAREFUL when closing the doors. Remove hands before the
door closes completely to prevent personal injury.
6. DO NOT stand on this product. You may fall, which may cause
personal injury.
7. Wear safety glasses when removing or repositioning the slides.
8. When moving this product, do not pull it. Push the product to
prevent personal injury.
9. Use the brakes when not moving this product. This will prevent the
product from rolling, which may cause personal injury or product
damage.
10. Be careful when opening more than one drawer at a time. The
product could become unstable and tip, which may cause personal
injury or product damage.
11. Secure this product properly before moving it with a forklift.
12. DO NOT tow with power equipment. The product could tip, which
may cause personal injury or product damage.
13. DO NOT alter this product in any manner. For example, do not weld
external lockbars or attach electrical equipment. This may cause
product damage or personal injury.
14. Keep the product on level surfaces. The product could become
unstable and tip if stored or moved on an uneven surface, which
may cause personal injury or product damage.
PRODUCT DESCRIPTION
The 0EMTO0LS® 72" 11 Drawer Cabinet and Upper Cabinet -
Stainless Steel combines the flexibility of a drawer toolbox with the
efficiency and organization of their patented peg tool storage system
to keep your tools organized and in one place in your shop or garage.
CABINET SPECIFICATIONS
Part #s 24615
Dimensions 72" (W) x 20-5/8" (D) x 72" (H)
Drawers 22" (W) x 3-1 /8" (H) (6)
22" (W) x 6-1 /8" (H) (2)
22" (W) x 9-3 /8" (H) (3)
ASSEMBLY STEPS
1. HANDLE INSTALLATION
NOTE:Assemble the handle first to make it easier to move the
cabinet. Position the handle over the holes in the cabinet and attach
with the 1/4" x 12 mm hex bolts provided. Tighten securely. Repeat
for the other handle on the other side of the cabinet.
2. CASTER INSTALLATION
CAUTION: Two or more people are required to lay down or stand
up the cabinet. Use the side handles for assistance. DO NOT stand
in front of or behind the product during this process. Lock drawers
before proceeding.
Carefully lay the cabinet on its back, with a soft mat underneath for
protection.
Position the two swivel casters on the cabinet bottom, on the left side.
Insert four 3/8" x 25 mm hex bolts through each caster and into the
bottom of the cabinet. Tighten securely.
Repeat for the two rigid casters on the other side of the cabinet.
3. RAIL, PEGBOARD AND UPPER CABINET INSTALLATION
Attach the four rails to the tool cabinet with four 1/4" x 14 mm hex
bolts each.

3
Operating Instructions and Parts Manual OEM24615
8/20
2020 OEMTOOLS®
72" 11 DRAWER CABINET AND
UPPER CABINET - STAINLESS STEEL
Attach the pegboard to the rails with twelve 1/4" x 14 mm hex bolts.
Attach the upper cabinet to the rails with twelve 1/4" x 14 mm hex bolts.
4. SHELF ASSEMBLY
Insert four hooks inside the upper cabinet at the desired height. Place
the shelf on the shelf supports.
Repeat for the other shelves.
DRAWER REMOVAL
Pull the drawer out so that it’s almost fully extended. Push up on
the black release lever on one side, while pulling down on the black
release lever on the other side.
While holding the levers in the positions as instructed above, pull the
drawer outward until it is released from the drawer slide.
ONE SIDE – PUSH UP
OTHER SIDE – PUSH DOWN
DRAWER REPLACEMENT
Extend the drawer slides from the tool cabinet. Insert the brackets on
each side of the drawer into the slots in the slides, being careful that
they are properly positioned. Once properly inserted, completely close
the drawer to set the slides in their proper positions.

4
Operating Instructions and Parts Manual OEM24615
8/20
2020 OEMTOOLS®
72" 11 DRAWER CABINET AND
UPPER CABINET - STAINLESS STEEL
Figure Part # Description Qty.
1 16028025AO Work Top 1
2 12038033AO Cabinet Handle 2
3 06128047AO 1/4" x 12 mm Hex Bolt 8
4 05108066AO Swivel Caster (with brake) 2
5 05108067AO Rigid Caster 2
6 06128046AO 3/8" x 25 mm Hex Bolt 16
7 05158013AO Lock (A-C) 5
8 05168093AO Drawer Liner 11
9 05148012AO Slide Set 14
10 04078767AO Rail 4
11 06808078AO Grommet 2
12 04078765AO Pegboard 1
13 04048570AO Hook 12
14 04048766AO Shelf 3
15 05138092AO Gas Strut 6
16 06128079AO 1/4" x 14 mm Hex Bolt 40
CABINET PARTS DIAGRAM
CABINET PARTS LIST
3580 E. Raines Road, Suite 3, Memphis, TN 38118
Tel: [phone]
www.oem-tools.com
OEMTOOLS®3 YEAR WARRANTY
For up to three years from the date of purchase of this OEMTOOLS®
product, if you find any defect in material or workmanship (through
normal usage), return it to the place of purchase or to OEMTOOLS®
for repair or replacement at our discretion. In order to obtain this
service, send your tool and proof of purchase (transportation
pre-paid) to: OEMTOOLS®Q.A. Dept., 3580 E. Raines Road #3,
Memphis, TN 38118.
We will not be responsible for lost or damaged goods during
transportation; please insure your package. If our inspection verifies
the defect, we will either repair or replace the product, or we may
elect to refund the purchase price if we cannot readily and quickly
provide you with a replacement. We will return repaired products at
our expense, but if we determine there is no defect, or that the defect
resulted from causes not within the scope of our warranty, then you
must bear the cost of returning the product.
OEMTOOLS®does not provide warranty for products labeled other
than OEM®or OEMTOOLS®. OEMTOOLS®will not provide any
warranty for products subjected to abnormal use. Abnormal use
includes (but is not limited to) abuse, accident, alteration, neglect, and
unauthorized or unreasonable use or repairs. This warranty does not
cover bits, blades, files, batteries, or calibration. We recommend that
you maintain your tools and sharpen or replace blades, bits, files, and
batteries as necessary. OEMTOOLS®reserves the right to make any
changes in construction or design at any time without any obligation
in incorporating such changes to tools or equipment previously sold.
OEMTOOLS®makes every effort to ensure that its products meet
high quality and durability standards, and warrants to the original
purchaser that this product is free from defects in materials and
workmanship for the period of three years from the date of purchase.
This warranty does not apply to damage due directly or indirectly to
misuse, abuse, negligence or accidents, repairs or alterations outside
our facilities, criminal activity, improper installation, normal wear and
tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or
property, or for incidental, contingent, special or consequential
damages arising from the use of our product. Some states do not
allow the exclusion or limitation of incidental or consequential
damages, so the above limitation of exclusion may not apply
to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES
OF MERCHANTABILITY AND FITNESS. This warranty gives you specific
legal rights, and you may also have other rights, which vary from
state to state.
Don’t forget to register your new OEMTOOLS®product at
www.oem-tools.com.
NOTE: Not all components of the Tool Cabinet are replacement items, but
are illustrated as a convenient reference for location and position in the
assembly sequence. The manufacturer and/or distributor have provided
the parts list and assembly diagram in this manual as a reference tool
only. Neither the manufacturer nor distributor makes any representation or
warranty of any kind to the buyer that he or she is qualified to make any
repairs to the product, or that he or she is qualified to replace any parts of
the product. In fact, the manufacturer and/or distributor expressly states
that all repairs and parts replacements should be undertaken by certified
and licensed technicians, and not by the buyer. The buyer assumes all
risk and liability arising out of his or her repairs to the original product
or replacement parts thereto, or arising out of his or her installation of
replacement parts thereto.
CONTACT US
THE KEYS, HANDLE AND CASTERS ARE
PLACED IN THE LOWER LEFT DRAWER