OfficeSource OX9245 User manual

OFFICE FURNITURE
MODEL NO. OX9245
OFFICESOURCE.COM Last Updated: 6/2022
ASSEMBLY INSTRUCTIONS
Minfix cap
12 Pcs
2
1
Cam Cam
12 Pcs
3
Shelf Pin
4 Pcs
4 6 7
Adjustable
Glide
5 Pcs
5
Cam Lock
12 Pcs
Bolt M6X30MM
12 Pcs
L-KEY
1 Pc
8 9
FLAT WASHER
8 Pcs
File Clip
2 Pcs
15
File Bar
1 Pc
14
Screw
#3.5 x 16mm
12 Pcs
10
Flat Plate
2 Pcs
11
Push Lock
1 Set
M3.5 x 12
CSK Screw
2 Pcs
12 13
Ø15mm
Hole Plug
4 Pcs
Remove all wrapping materials, including staples & packing straps before you start to assemble.
Do not tighten any screws or bolts until the unit is completely assembled.
Keep all hardware parts out of reach of children.
Check that you have all parts and hardware.
KLIX CAM INSTRUCTIONS
SIDE PANEL-L
TOP PANEL
BC
Insert the cam with the arrow pointing
towards the hole in the edge.
Line up Cam Lock, turn
clockwise.
1 2
Insert the Cam Lock into Klix Cam. Turn
Klix Cam to lock.
3
PAGE 1 OF 3
REV. 1 OX9245_AI
ASSEMBLY INSTRUCTION FOR 47" CREDENZA
HARDWARE
IMPORTANT NOTE :
Place all wooden parts on a clean, smooth surface to prevent the parts from being scratched.
COMPONENTS
SIDE PANEL-R BOTTOM PANEL BACK PANEL ADJUST SHELF PANEL
D E F J
WOODEN LEG X 4PCS
RIGHT
LEFT
A
FIXED SHELF PANEL
G
A
SUPPORT LEG
K
BOX BOX FILE
L
INCLUDED WITH OX9245 A
INCLUDED WITH OX9245 B
L
H
I
H
LEFT DOOR
I
RIGHT DOOR
J
J
A
L
H
I
J
J
16
Handle
3 Pcs
®

OFFICE FURNITURE
MODEL NO. OX9245
OFFICESOURCE.COM Last Updated: 6/2022
ASSEMBLY INSTRUCTIONS
5
67
6
7
8
WOODEN LEG
PUSH
TO
RELEASE
1
PAGE 2 OF 3
REV. 1
3
Attach Cam Cap (3) to all Klix
Cam(2) by pushing neck through
center of cam.
3
2
Attach Side Panel-L(B) & Side Panel-R(C)
to Fixed Shelf(G) & Back Panel(E) then
attach Bottom Panel(D) to Side
Panels(B,C) using Cam Lock(1) and Klix
Cam(2).
Press drawer slide release tab and remove the top drawer
and bottom drawer.
OX9245_AI
D
G
B
EC
L
4
L
G
D
C
A
Attach Wooden Leg(J)
to Bottom Panel(D)
using Bolt(6)
Insert Adjustable
Glides(5) into
bottom of Wooden
Leg(J) & Support
Leg(K).
Screw Support Leg(K) to
Bottom Panel(D)
D
K
Attach Flat Plate(10) using
Screw(9) to Bottom Panel(D) &
Bottom BBF(L)
J
D
J
ASSEMBLY INSTRUCTION FOR 47" CREDENZA
LEFT
Attach B/B/F(L) & Fixed
Shelf(G) to Top Panel(A)
and secure with Bolt(6) &
Flat Washer(8)
L
D
9
10
®

OFFICE FURNITURE
MODEL NO. OX9245
OFFICESOURCE.COM Last Updated: 6/2022
ASSEMBLY INSTRUCTIONS
15
14
11
12
UP DOWN
13
PAGE 3 OF 3
REV. 1 OX9245_AI
ASSEMBLY INSTRUCTION FOR 47" CREDENZA
4Insert Shelf Pins(4) and
place Shelf(F) in desired
location.
Insert the Hole Plug (13)
into Bottom Panel(D).
Attach the File Clip(14) on the drawer side.
Insert the File Bar(15) into the clip.
5
Attach Push Lock(11) to
back of Right Door(I)
using Screw(12).
Retract roller slide into
Door(H)&(I) when
installing.
To adjust door height
turn adjusting screw as
needed.
6
AC
F
E
D
J
L
16
16
Attach the
Handle(16) on the
Drawer
Front.Reinstall the
Top drawer &
Bottom drawer
L
A
HI
5
67
67
8
WOODEN LEG
4
L
G
D
B
A
Attach Wooden Leg(J)
to Bottom Panel(D)
using Bolt(6)
Insert Adjustable
Glides(5) into
bottom of Wooden
Leg(J) & Support
Leg(K).
Screw Support Leg(K) to
Bottom Panel(D)
D
K
Attach Flat Plate(10) using
Screw(9) to Bottom Panel(D) &
Bottom BBF(L)
J
D
J
RIGHT
Attach B/B/F(L) & Fixed
Shelf(G) to Top Panel(A)
and secure with Bolt(6) &
Flat Washer(8)
L
D
9
10
Insert Left Door(H) first,
then Right Door(I).
®