OfficeSource PPPSTRAIGHT User manual

Ensure all bolts and screws are tightened, check bolts and screws every 6 months.
If any parts are missing, broken, damaged or worn, stop use of product until repairs have been made using factory authorized parts.
Failure to follow these warnings may result in injury.
ATTENTION
!!
Nylon Clip
qty = 2 pcs qty = 10 pcs
Flat Bracket (Tie Bracket)
1 of 2
qty = 2 pcs
Mid Cap
In the Carton : In the Carton :
Self drilling screw
@ #6x1/2" = 28 pcs
nylon clip
face-down
nylon clip
face-up
nylon clip side
In the Carton : In the Carton :
1
M6x16 bolt
qty = 6 pcs
screw #10x5/8"
Qty = 8 pcs qty = 2 pcs
V base castor Leg
1. Lay the panels down on a flat clean surface for assembly
2. Remove the end caps (side trim) from the panels from both sides of each panel
3. Install 5 of the nylon clips face up (see image to the right) to the side being joined on one of the panels
a. Screw the nylon clips to the panels using 2 of the #6 x ½” Self drilling screws. There will be 3 holes
drilled in a triangular shape – leave the center hole empty
4. Install 5 of the nylon clips face down (see image to the right) to the side being joined on the other panel
a. Screw the nylon clips to the panels using 2 of the #6 x ½” Self drilling screws. There will be 3 holes
drilled in a triangular shape – leave the center hole empty
(PPPDELFOOTCPR)
Sold Separately :
acrylic
Before assembly, please remove all parts from carton, verifying that you have the correct quantities, and read all the insructions.
ASSEMBLY INSTRUCTIONS
MODEL: PPPSTRAIGHT
Leg bracket
nylon clip side
5. Install the V Base Castor Leg to the outside of the 2 connected panels,
following the instructions outlined in the V Base Leg, model #
PPPDELFOOTCPR, (sold separately).
6. Re-attach panel side trims to the outsides of the panels (the same sides
the V Base Caster Leg is on)
Last Updated: 02/2021
MODEL NO. PPPSTRAIGHT
OFFICESOURCE.COM
ASSEMBLY INSTRUCTIONS
Last Updated: 3/2023

Ensure all bolts and screws are tightened, check bolts and screws every 6 months.
If any parts are missing, broken, damaged or worn, stop use of product until repairs have been made using factory authorized parts.
Failure to follow these warnings may result in injury.
ATTENTION
!!
7. Stand the panels up and place the sides with the clips together.
This step is made easier if a block of wood, or other support is
placed under the panel that has the Nylon Clips facing upwards
8. Press the panel that has the Nylon Clips facing downwards
against the panel with the Nylon Clips facing upwards until the clips
have securely locked together
a. This will be shown by the panel tops and bottoms being level
9. Remove both panel top caps
10. Remove the metal trim that is installed in the top corner (this is
the bracket that transitions from the panel top cap to the panel side
cap, so the top corner looks smooth) on the side that is to be joined
to the other panel only
11. Install the Mid-Cap in replacement of the corner piece that was
just removed (this only goes on the side of the panel that is being
attached to another panel)
12. Slide the Flat Bracket (Tie Bracket) through the gap under the Mid Cap
1
2
wood block
1
2
flat bracket
top cover
(tie bracket)
13. Screw the Tie Bracket to the top of the panels using 2x #6 x ½”
Self Drilling Screws on each panel (total of 4 screws used in this step)
14. Replace the metal top caps
15. Lay the panels back onto their sides
16. Press the 2nd Tie bracket up against the bottom of the panels, and
install it by screwing 2x #6 x ½” screws into each panel (the same
format as the top), (a total of 4 screws used in this step)
a. Note there is no cap to remove when mounting the bottom bracket
17. Stand panels up to complete
acrylic
acrylic
acrylic acrylic
2 of 2
Before assembly, please remove all parts from carton, verifying that you have the correct quantities, and read all the insructions.
ASSEMBLY INSTRUCTIONS
MODEL: PPPSTRAIGHT
Last Updated: 02/2021
MODEL NO. PPPSTRAIGHT
OFFICESOURCE.COM
ASSEMBLY INSTRUCTIONS
Last Updated: 3/2023