OfficeSource PL438T HALF User manual

KLIX CAM INSTRUCTIONS
Insert the cam with the arrow
pointing towards the hole in the
edge.
Line up Cam Lock,
turn clockwise.
12
Insert the Cam Lock into Klix
Cam. Turn Klix Cam to lock.
3DETAIL x-x
ADJUST THIS SCREW FOR DOOR ALIGNMENT
AFTER ASSEMBLY THE HINGES.
BACK VIEW
HINGES INSTRUCTIONS
MODEL: PL 438T HALF
1 OF 6
Before assembly, please remove all parts from carton, verifying that you have the correct quantities, and read all the instructions.
CONFIGURATION:
ASSEMBLY INSTRUCTIONS
See Page 3 See Page 4
See Page 5 See Page 6
WITH END BASE WITH ELLIPTICAL BASE
WITH CUBED BASE WITH V-LEG/U-LEG BASE
See Page 6
WITH V-LEG/SQUARE
POST LEG BASE
WALL
®
®
OFFICE FURNITURE
MODEL NO. PL438T HALF
OFFICESOURCE.COM Last Updated: 10/2021
ASSEMBLY INSTRUCTIONS
Part 1 of 6

2 OF 6
!ATTENTION !
Place all wooden parts on a clean, smooth surface to prevent them from being scratched.
Check to be sure that you have all parts and hardware. Remove all wrapping materials, including staples and packing straps before
you start to assemble. Do not tighten all screws/bolts until all completely assembled. Keep all hardware parts out of reach of children.
If any parts are missing, broken, damaged or worn, stop use of product until repairs have been made using factory authorized parts.
Failure to follow these warnings may result in injury.
MODEL: PL 438T HALF
ASSEMBLY INSTRUCTIONS
COMPONENTS:
HARDWARE:
G1 G2 G3
M4 x 65
Allen-Key
1 Pc
Adjustable
Glide
5 Pcs
G4 G5 G6
JCBC Screw
M6 x 40mm = 8pcs
14Washer = 8pcs
Klix Cam
18 Pcs
Housing
Cap (Short)
4 Pcs
Cam Lock
18 Pcs
G7
6 Hole
L-Bracket
4 Pcs
Screw
#6 x 58"
24 Pcs
G8 G9
0' Compo
Door Hingers
1 Pair
Screw
#3.5 x 16mm
2 Pcs
Magnet
Catches
1 Set
Screw
#3.5 x 12mm
2 Pcs
G10 G11 G12
Housing
Cap (Long)
14 Pcs
G13
Modesty Panel x
2 Pcs
BA
End Base x 2
C
++
+
Cube Base x 2
G
Center Base
E
+
Modesty Panel x
2 Pcs
B
++
Elliptical Base x 2
DF
Center
Elliptical Base
+
+
PLT-V-LEG x 2
H
+
PLT-RET Support x 8
J
PLT LEG-U
I
+
+
PLT-V-LEG
H
+
PLT-RET Support x 2
J
PLT Post Leg x 2
K
+
A A
A
A
FOR
ELLIPTICAL
BASE
FOR
CUBE
BASE
FOR
V-LEG/U-LEG
BASE
FOR END
BASE
+
Top Panel for PL438T
HALF x 2
Top Panel for PL438T
HALF x 2
Top Panel for PL438T
HALF x 2
Top Panel for PL438T
HALF x 2
ATop Panel for PL438T
HALF x 2
H1 H2 H3
#6 x 16mm P/H
Cross Recess
Screw
4 Pcs
Screw
#4 x 16mm
16Pcs
M4 x 65
Allen-Key
1 Pc
I1 I2 I3
#6 x 16mm P/H
Cross Recess
Screw
4 Pcs
Screw
#4 x 16mm
16Pcs
M4 x 65
Allen-Key
1 Pc
J1
Screw
#4 x 16mm
32Pcs
Klix Cam
10 Pcs
Cam Lock
10 Pcs
M4 x 65
Allen-Key
1 Pc
Housing
Cap (Short)
4 Pcs
Housing
Cap (Long)
6 Pcs
Adjustable
Glide
4 Pcs
C8
Screw
#6 x 58"
24 Pcs
C1 C2 C3 C4 C5 C7
6 Hole
L-Bracket
4 Pcs
C6
A1
Klix Cam
6 Pcs
Cam Lock
6 Pcs
M4 x 65
Allen-Key
1 Pc
Housing
Cap (Long)
6 Pcs
Adjustable
Glide
4 Pcs
D7
Screw
#6 x 58"
24 Pcs
D1 D2 D3 D4 D6
6 Hole
L-Bracket
4 Pcs
D5 D8
CSK Scew
M3.5 x 20MM
16 Pcs
Klix Cam
4 Pcs
Cam Lock
4 Pcs
M4 x 65
Allen-Key
1 Pc
Housing
Cap (Long)
4 Pcs
Adjustable
Glide
2 Pcs
E7
Screw
#6 x 58"
24 Pcs
E1 E2 E3 E4 E6
6 Hole
L-Bracket
4 Pcs
E5 E8
CSK Scew
M3.5 x 20MM
8 Pcs
Klix Cam
4 Pcs
Cam Lock
4 Pcs
M4 x 65
Allen-Key
1 Pc
Housing
Cap (Long)
4 Pcs
Adjustable
Glide
2 Pcs
F7
Screw
#6 x 58"
24 Pcs
F1 F2 F3 F4 F6
6 Hole
L-Bracket
4 Pcs
F5 F8
CSK Scew
M3.5 x 20MM
8 Pcs
K1
Screw
#4 x 16mm
8Pcs
INCLUDED
WITH TABLE
TOP
INCLUDED
WITH CUBE
BASE
INCLUDED
WITH
V-LEG/U-LEG/SQUARE
POST LEG
BASES
INCLUDED
WITH END
BASES
INCLUDED WITH
ELLIPTICAL
BASES
INCLUDED
WITH CENTER
END BASE
INCLUDED
WITH CENTER
ELLIPTICAL
BASE
Screw
#6 x 58"
60 Pcs
6 Hole
L-Bracket
8 Pcs
Flat-Bracket
2 Pcs
A2 A3
®
®
OFFICE FURNITURE
MODEL NO. PL438T HALF
OFFICESOURCE.COM Last Updated: 10/2021
ASSEMBLY INSTRUCTIONS
Part 2 of 6

MODEL: PL 438T HALF
ASSEMBLY INSTRUCTIONS
3 OF 6
INSTRUCTION:ASSEMBLING TABLE WITH END PANEL BASE
Screw Adjustable Glide (C5) into
bottom of End Base (C).
4
Attach Housing Cap (A3/C3/C4) to
all Klix Cam(A2/C2) by pushing
neck thought center of cam.
C5
3
1
BOTTOM
FACE
A
A
5
2
C
(A3/C3/C4)
A2
A3
Attach the Flat-Bracket (A2) to
two Top Panel (A) as shown.
Tighten Screws (A3) securely.
BOTTOM
FACE
Attach the two End Base (C) and
Center Base (E) to Modesty Panel
(B) by using Cam Lock (C1) and Klix
Cam (C2).
B
TOP
C
E
C
B
Attach the body (B/C/E) to Top
Panel (A) by using Cam Lock
(C1/E1) and Klix Cam (C2/E2). A
B
TOP
Attach the L-Bracket (A1/C6/E6) to End
Base (C) and Center Base (E) and
Modesty Panel (B) as shown. Tighten
Screws (A3/C7/E7) securely.
E
C
B
C
A
(A3/C7/E7)
(A1/C6/E6)
®
®
OFFICE FURNITURE
MODEL NO. PL438T HALF
OFFICESOURCE.COM Last Updated: 10/2021
ASSEMBLY INSTRUCTIONS
Part 3 of 6

MODEL: PL 438T HALF
ASSEMBLY INSTRUCTIONS
4 OF 6
INSTRUCTION:ASSEMBLING TABLE WITH ELLIPTICAL BASE
4
Attach Elliptical Base (D) and Center Elliptical
Base (F) to Modesty Panel (B) by using Cam
Lock (D1/F1) and Klix Cam (D2/F2).
2
BOTTOM
FACE
A
A
3
A2
A3
Attach the Flat-Bracket (A2) to
two Top Panel (A) as shown.
Tighten Screws (A3) securely.
Attach metal plate to Elliptical Base (D)&(F)
with included screws.
D4
F
Screw Adjustable Glides (D4)&(F4) into
bottom of Elliptical Bases (D)&(F).
D
Attach Elliptical Base (D) and
Center Elliptical Base (F) to Top
Panel (A) by using Screw (D8/F8).
A
A
D
F
D
B
BAttach the L-Bracket (A1/D5/F5)
from Top Panel (A) to Elliptical
Base (D) and Modesty Panel (B)
and Center Elliptical Base (F)
as shown. Tighten Screws
(A3/D8/F8) securely.
Attach Top Panel (A) to Modesty Panel (B) by
using Cam Lock (D1/F1) and Klix Cam (D2/F2).
(A1/C5/D5)
(A3/C8/D8)
D
B
B
1
&D
F4
&
F
&&
F
D
A
CF8D8 &
D F
®
®
OFFICE FURNITURE
MODEL NO. PL438T HALF
OFFICESOURCE.COM Last Updated: 10/2021
ASSEMBLY INSTRUCTIONS
Part 4 of 6

MODEL: PL 438T HALF
ASSEMBLY INSTRUCTIONS
5 OF 6
INSTRUCTION:ASSEMBLING TABLE WITH CUBED BASE
Assemble Cube Base by attaching Side
Panels(C)&(D) to Back Panels(E),Top
rail(F) & Bottom Rail(G) with Cam Lock
(G1) and Klix Cam (G2).
Attach Cube Base Support (B) by using Cam Lock (D1) and Klix Cam (D2).
3
F
G
C
D
H
COR D
H
G10
B
G10
G9
H
CD
OR
G8
B
C
D
&
Attach Magnet Catches(G10) to Side
Panel(C)or(D) by using Screw(G11).
Attach L-Bracket(G7) to
Side Panel(C)&(D) and
Hanging Rail(B) by using
Screw(G8).
Attach Hinges(G9) to Side
Panel(C)or(D) and Door(H) by using
Screw(G9).
Attach Catches Plate(G10) to
Door(H) by using Screw(G12).
C
D
G
E
F
Screw Adjustable Glide
(G5) into bottom of End
Base (C,D).
G5
C
D
G
E
2
1
G7
B
G12
G11
4
A
Attach the Flat-Bracket
(A2) to two Top Panel (A)
as shown. Tighten Screws
(A3) securely.
A2
A3
BOTTOM
VIEW
A
G13
G6
Attach Top Panels (A) to
Cube Bases (B) with JCBC
Screws (G13) and tighten
with Allen Key G6).
G
G
®
®
OFFICE FURNITURE
MODEL NO. PL438T HALF
OFFICESOURCE.COM Last Updated: 10/2021
ASSEMBLY INSTRUCTIONS
Part 5 of 6

6 OF 6
ASSEMBLY INSTRUCTIONS
MODEL: PL 438T HALF
Attach Screws
#4 x 16mm(H2/I1) to
PLT-V-Legs.
I1
H2 I1
Attach PLT V-Legs(E) to
Top Panel(A) by using
#6 x 16mm P/H Cross
Recess Screws(I1).
A
HJ
I1
Attach PLT LEG-U(F)
to Top Panel(A) by
using #6 x 16mm P/H
Cross Recess
Screw(I1).
2
A
H
IJ
H2 J1
Attach Screw
#4 x 16mm(H2/J1)
to PLT Leg-U(F).
Attach Screws
#4 x 16mm(H1/I2) to
PLT-V-Legs.
A
H
J
K
H2 I1
I1
Attach PLT V-Legs(E) to
Top Panel(A) by using
#6 x 16mm P/H Cross
Recess Screws(I1).
H
F
3
J
K1
A
Attach PLT Square Post
Legs(H) to Top Panel(A)
by using screws #4 x
16mm(K1)
INSTRUCTION:ASSEMBLING TABLE WITH V-LEG BASE
1
®
®
OFFICE FURNITURE
MODEL NO. PL438T HALF
OFFICESOURCE.COM Last Updated: 10/2021
ASSEMBLY INSTRUCTIONS
Part 6 of 6