OfficeSource RCN3131C User manual

ASSEMBLY INSTRUCTIONS
RCN3131C

Assembly HARDWARE
S/N PICTURE NAME TOTAL QTY
ACAM SCREW
REMARK
B
C
F
G
H
I
GLASS SPACERS
CONNECTOR SCREW
GROMMET
LEVELER
CAM COVER STICKER
KLIX CAM
use cam covers
to cover any klix
cam
SCREWS
F1
F2
20PCS
20PCS
28PCS
5PCS
4PCS
2PCS
5PCS
Use to connect to
another desk
ASSEMBLY INSTRUCTIONS
RCN3131C

PART LIST
COUNTER TOP
COUNTER SUPPORTS
DESK SIDES
BASE BACK
16
12
13 14
15
17 18
19
20
21
24
22 23
25
12
16
13 14
17 18
15
19
BASE SUPPORTS
22 23
25
21
24 BASE BOTTOM
27
20
27
DESK TOP
COUNTER BACK
DESK BACK
DESK BOTTOM
CENTER SUPPORT PANEL
CURVED GLASS COUNTER TOP
Counter
Desk
Base
Double
Double
Double
Note: Additional Parts 15, 19, and 20 Included
21
25
23
24
I
22
1. INSTALL "I" LEVELERS ON THE BOTTOM OF
I(5x)
24
Bottom Parts 21, 22, 23, 24, and 25 come Pre-Assembled.
RCN3131C
ASSEMBLY INSTRUCTIONS

CONNECT 21 DESK BOTTOM TO 17 & 18 DESK SIDES & 19 BACK PANEL & 20
CENTER SUPPORT. INSTALL 19 LAST. SEE TWO STEPS BELOW.
<1> INSTALL "A" CAM SCREWS IN 21 AND "B" KLIX CAMS IN 17 18 AND 20
.CONNECT 17 18 AND 20 TO 21 ,TIGHTEN.
A(6x)
B(6x)
3.
24
21
18
17
22 23
20
25
INSTALL "H" GROMMETS ON SIDE PANELS 17 & 18.
H(2X)
2.
18
17
H
LOCKING
TURN FOR
1/4 RIGHT
FUNCTION OF KLIX CAX
IMPORTANT:
MAKE SURE THE ARROW IS
POINTING TO THE OPEN
HOLE BEFORE INSERTING
INTO THE PANELS HOLE
RCN3131C
ASSEMBLY INSTRUCTIONS

<2> BEND AND SLIDE CURVED BOARD 19
INTO GROOVES ON 17 AND 18 .
24
21
18
17
22 23
19
20
25
18
17
16
INSTALL "A" CAM SCREWS ON UNDERSIDE OF TOP 16. INSTALL "B" KLIX CAMS
ON PANELS 17 , 18 AND 20 . CONNECT 16 TO 17 , 18 AND 20 USING
INSTALLED CAM SCREWS AND KLIX CAMS. TIGHTEN.
A(6x)
B(6x)
20
19
2322
21
24
4.
B
ASSEMBLY INSTRUCTIONS
RCN3131C

6.INSTALL "A" CAM SCREWS ON THE UNDERSIDE OF COUNTER TOP 12 .
INSTALL "B" KLIX CAMS ON SUPPORTS 13 AND 14 . CONNECT 12 TO 13 AND
14 USING INSTALLED CAM SCREWS AND KLIX CAMS. TIGHTEN.
A(4X)
B(4X)
16
18
17
20
19
21
24
22 23
13 14
15
12
INSTALL "A" CAM SCREWS ON PANEL 16 , INSTALL "B" KLIX CAMS ON SIDE
PANELS 13 & 14 . THEN CONNECT PANELS 13 & 14 TO 16 USING ALREADY
INSTALLED" A" CAM SCREWS . TIGHTEN. THEN BEND AND SLIDE CURVED
BOARD 15 INTO GROOVES ON 13 & 14 .
A(4X)
B(4X)
16
18
17
20
19
21
24
22 23
13
14
16
18
17
20
19
21
24
22 23
13 14
15
B
A
5.
B
RCN3131C
ASSEMBLY INSTRUCTIONS

12
16
18
17
20
19
21
24
22 23
13 14
12
16
18
17
20
19
21
24
22 23
13 14
ATTACH THE CURVED GLASS COUNTER TOP 27 TO CENTER 12 USING
"F1" GLASS SPACERS AND "F2" SCREWS WITH CARE.
F1(5x)
F2(5x)
F1
F2
USE "C" CAM COVER STICKERS TO COVER ALL EXPOSED KLIX CAMS ON ALL
COMPONENTS.
C(28X)
C
27
27
7.
8.
Note: If using on an end, Use "C" cam cover stickers to cover additonal holes on 17 and/or 18 .
RCN3131C
ASSEMBLY INSTRUCTIONS