OHAUS SJX1502N/E Operating manual

Additional Instructions ScoutSJX Balances
Ohaus Corporation www.ohaus.com iScoutSJX Balances
UNPACKING
Carefully remove your Scout balance and each of its components from the
package. Store the packaging material to ensure safe storage and future transport.
Included Components:
Balance
Pan
User Guide &
Instructions
Calibration Mass (only for SJX/E models with 64g
capacity)
Warranty Card
Scoop (only for models with 64g capacity)
AC Adapter & Plug
CALIBRATION
When the balance is operated for the first time, a calibration is recommended to
ensure accurate weighing results.
External Span Calibration
With balance turned on:
Step-1
Press and hold Menu until [mMeNU] (Menu) is displayed.
Step-2
Release the button, the display will show [C.A.L].
Step-3
Press Yes to accept. [SpaN] will then be shown.
Step-4
Press Yes to begin the span calibration. Zero reading is stored
automatically.
Step-5
Place the specified span calibration mass on the pan. Then, press Yes
to accept the weight or No to select an alternate weight.
[--C--] will be displayed while the reading is stored
The display will show [done] if the calibration was successful. The
balance returns to the previous application mode and is ready for use.
Internal Calibration (not available for SJX/E models)
With balance turned on:
Step-1
Press and hold Menu until [mMeNU] (Menu) is displayed.
Step-2
Release the button, the display will show [C.A.L].
Step-3
Press Yes to accept. [In.CAL] will then be shown.
Step-4
Press Yes to begin the Internal calibration. Zero reading is stored
automatically.
Step-5
Pull the InCal handle while the display show
[PULL].
Step-6
Push the InCal handle while the display
show [PUSH].
Step-7
Repeat the step-5, and step-6 one more
time.
Step-8
The display will show [done] if the calibration was successful. The
balance returns to the previous application mode and is ready for use.
Visit www.balances.com for balances, scales & calibration weights
Visit www.scaleman.com to purchase Ohaus Scout SJX Scale

Scout SJX Balances Additional Instructions
ScoutSJX Balances ii Ohaus Corporation www.ohaus.com
OPERATION & APPLICATIONS
The balance can be configured to operate in one or more Application modes.
Press and hold Mode key to select your Application mode.
The Scout SJX balance incorporates the following Applications:
[wWeIGH]
[Count]
[Percnt]
[CHeCk]
[total]
[SPEC.Gr]
[Hold]
Weighing
Parts
Counting
Percent
Weighing
Check
Weighing
Totalization
Density
Determination
Display
Hold
ADDITIONAL FEATURES
Connecting the Interface
Use an optional interface connectivity kit to
connect the balance either to a computer,
printer or OHAUS auxiliary display.
Below Interface kit accessories are available:
RS232, USB Host, USB Device, Ethernet,
Bluetooth*.
Interface connection on the rear of
the balance:
* Interface kits may vary according to local regulations
Weigh Below Hook
The weigh below hook is located at the reverse side of the battery cover as shown.
To use this feature, remove the red protective cover underneath for the weigh below
opening. For SJX, the weigh below hook is integrated and located under the
protective cover. For SJX/E, the weigh below hook is stored in the battery
compartment (back side of the battery cover).
INSTRUCTION MANUAL
For more detailed information about the balance,
please refer to the product instruction manual. The
instruction manual can be obtained either by
scanning the QR code or by going to the Scout SJX
product page to download it.
Go to www.ohaus.com to register your product's
warranty.
Product Page: http://www.ohaus.com/
QR Code:
Interface connection
AC Adapter Jack
Security slot
Weigh below protective cover
Weigh below hook
(SJX/E only)
Visit www.balances.com for balances, scales & calibration weights
Visit www.scaleman.com to purchase Ohaus Scout SJX Scale