OLIMEX TMS320-XDS100-V3 User manual

TMS320-XDS100v3
DSP and ARM emulator and adapter
USER’S MANUAL
Revision B, September 2012
Designed by OLIMEX Ltd, 2012
All boards produced by Olimex LTD are ROHS compliant

OLIMEX© 01 TMS3 0-XDS100v3 User's Manual
D SCLA MER
© 2012 Olimex Ltd. Olimex®, logo and combinations thereof, are registered trademarks of Olimex
Ltd. Other product names may be trademarks of others and the rights belong to their respective
owners.
The in ormation in this document is provided in connection with Olimex products. No license, express
or implied or otherwise, to any intellectual property right is granted by this document or in connection
with the sale o Olimex products.
It is possible that the pictures in this manual differ from the latest revision of the board.
The product described in this document is subject to continuous development and improvements. All
particulars of the product and its use contained in this document are given by OLIMEX in good faith.
However all warranties implied or expressed including but not limited to implied warranties of
merchantability or fitness for purpose are excluded. This document is intended only to assist the reader in the
use of the product. OLIMEX Ltd. shall not be liable for any loss or damage arising from the use of any
information in this document or any error or omission in such information or any incorrect use of the
product.
This evaluation board/kit is intended for use for engineering development, demonstration, or evaluation
purposes only and is not considered by OLIMEX to be a finished end-product fit for general consumer use.
Persons handling the product must have electronics training and observe good engineering practice
standards. As such, the goods being provided are not intended to be complete in terms of required design-,
marketing-, and/or manufacturing-related protective considerations, including product safety and
environmental measures typically found in end products that incorporate such semiconductor components or
circuit boards.
Olimex currently deals with a variety of customers for products, and therefore our arrangement with the user
is not exclusive. Olimex assumes no liability for applications assistance, customer product design, software
performance, or infringement of patents or services described herein.
THERE IS NO WARRANTY FOR THE DESIGN MATERIALS AND THE
COMPONENTS USED TO CREATE TMS320-XDS100v3. THEY ARE
CONSIDERED SUITABLE ONLY FOR TMS320-XDS100v3.
Page of 13

OLIMEX© 01 TMS3 0-XDS100v3 User's Manual
Table of Contents
D SCLA MER ............................................................................................................. 2
CHAPTER 1 OVERV EW ......................................................................................... 4
1. ntroduction to the chapter .......................................................................................... 4
1.1 Features ....................................................................................................................... 4
1.2 Target market and purpose of the board .................................................................. 5
1.3 Organization ............................................................................................................... 5
CHAPTER 2 SETT NG UP THE TMS320-XDS100v3 ........................................... 6
2. ntroduction to the chapter .......................................................................................... 6
2.1 Electrostatic warning ................................................................................................. 6
2.3 Requirements .............................................................................................................. 6
2.4 Powering the board and installation procedure ....................................................... 6
CHAPTER 3 TMS320-XDS100v3 DESCR PT ON ................................................. 8
3. ntroduction to the chapter .......................................................................................... 8
3.1 Layout (top view) ........................................................................................................ 8
CHAPTER 4 NTERFACES AND HARDWARE .................................................... 9
4. ntroduction to the chapter .......................................................................................... 9
4.1 Connectors .................................................................................................................. 9
4.1.1 JTAG ................................................................................................................................. 9
4.1.2 JTAG_14 ........................................................................................................................... 9
4.1.3 JTAG_20 ........................................................................................................................... 9
4.2 LEDs ............................................................................................................................ 9
4.2.1 Power LEDs ...................................................................................................................... 9
4.2.2 D3 and D4 ....................................................................................................................... 10
4.3 Jumpers ..................................................................................................................... 10
CHAPTER 5 REV S ON H STORY AND SUPPORT .......................................... 11
5. ntroduction to the chapter ........................................................................................ 11
5.1 Document revision .................................................................................................... 11
5.2 Useful web links and purchase codes ...................................................................... 12
5.3 Product support ........................................................................................................ 13
Page 3 of 13

OLIMEX© 01 TMS3 0-XDS100v3 User's Manual
CHAPTER 1 OVERV EW
1. ntroduction to the chapter
Thank you for choosing the TMS3 0-XDS100v3 emulator from Olimex! This document provides a
user’s guide for the Olimex TMS3 0-XDS100v3. As an overview, this chapter gives the scope of
this document and lists the board’s features. The differences between the members of the TMS3 0-
XDS100v3 family are mentioned. The document’s organization is then detailed.
The emulator is based on design provided and distributed by Texas Instruments.
1.1 Features
•TMS3 0-XDS100V3 hardware is designed to work with CCS 5.x software
•IEEE 1149.7 capable emulator with a USB interface.
•Can function as an 1149.7 adapter for use with existing scan controllers.
•Support for ARM Ltd's Single Wire Output (SWO).
•Software compatible with XDS100v (except link delay and IEEE 1149.7 modes).
•Physical jumper to select emulator or adapter mode.
•Operates in 1149.7 Class 4, up to 5MHz.
•LED to indicate IEEE 1149.7 Class 4 operation.
•LED to indicate operation in adapter mode.
•Supported devices: TMS3 0C 8xx, TMS3 0C54xx, TMS3 0C55xx, TMS3 0C674x,
TMS3 0C64x+, TMS3 0C66x, ARM9, ARM Cortex A9, ARM Cortex A8, ARM Cortex
M3, ARM Cortex R4
•Suitable for ARM 14 pin and ARM 0 pin layouts
•Works with targets in the 1.65 – 5.0V range
•Uses standard 0.1" x7 pin and x10 pin JTAG connector
•No need for external power supply, all required power is taken from USB and the target
•Dimensions 95x46 mm (3.75x1.8") + x15 cm (8") cables
For full list of features visit the TI's wiki address:
http://processors.wiki.ti.com/index.php/XDS100#XDS100v3_Features
Page 4 of 13

OLIMEX© 01 TMS3 0-XDS100v3 User's Manual
1.2 Target market and purpose of the board
The main purpose of the board is programming Texas Instrument's DSP (digital signal processing)
chips AND ability to program high-speed ARM chips. The board can also act as adapter to existing
scan controllers.
The design of the board follows the suggestions and the schematics provided by Texas Instruments.
1.3 Organization
Each section in this document covers a separate topic, organized as follow:
–Chapter 1 is an overview of the board usage and features
–Chapter provides a guide for quickly setting up the board
–Chapter 3 contains the general board diagram and layout
–Chapter 4 mentions the main software tools used with TMS3 0-XDS100v3
–Chapter 5 is an explanation of the interfaces, the leds, the jumpers position
–Chapter 6 contains the revision history, useful links and support information
Page 5 of 13

OLIMEX© 01 TMS3 0-XDS100v3 User's Manual
CHAPTER 2 SETT NG UP THE TMS320-XDS100v3
2. ntroduction to the chapter
This section helps you set up the TMS3 0-XDS100v3 emulator/adapter for the first time.
Please consider first the electrostatic warning to avoid damaging the board, then discover the
hardware and software required to operate the board.
The procedure to power up the board is given, and a description of the default board behavior is
detailed.
2.1 Electrostatic warning
TMS3 0-XDS100v3 is shipped in a protective anti-static package. The board must not be exposed
to high electrostatic potentials. A grounding strap or similar protective device should be worn when
handling the board. Avoid touching the component pins or any other metallic element.
2.3 Requirements
In order to set up the TMS3 0-XDS100v3 optimally, the following items are required:
- USB-A to mini-USB cable
- Set of software tools (preferably Code Composer Studio 5 – check the table -
http://processors.wiki.ti.com/index.php/XDS100#XDS100_Installation_Instructions)
- a TARGET from the supported list (can be found here:
http://processors.wiki.ti.com/index.php/XDS100#XDS100v3_Features)
Note that there are two ribbon cables included in the package – for the JTAG_14 and the JTAG_ 0
connectors.
2.4 Powering the board and installation procedure
The board is powered via the USB.
A. Install Code Composer Studio 5.1.x before connecting XDS100 USB hardware.
Page 6 of 13

OLIMEX© 01 TMS3 0-XDS100v3 User's Manual
B. Install the EmuPack with XDS100v3 support.
C. Connect the XDS100 hardware
1. Make sure the Code Composer Studio 5.1.x and EmuPack with XDS100v3 support is
installed FIRST before plugging in the XDS100 HW to the PC.
. Connect USB cable from the PC to the XDS100 hardware. Connect the JTAG to the
target board (be careful to plug it in correctly: pin 1 should go to pin 1. Red strip usually
indicates the side of pin 1)
3. You will notice small popups to inform user that USB hardware is recognized and
installed correctly. No input are required.
D. Setup Code Composer Studio v5.1.x
4. Start Code Composer Studio and create a new target configuration.
5. Select XDS100v3 as connection type
6. Select device (target).
Page 7 of 13

OLIMEX© 01 TMS3 0-XDS100v3 User's Manual
CHAPTER 3 TMS320-XDS100v3 DESCR PT ON
3. ntroduction to the chapter
Here you get acquainted with the main parts of the board. Note the names used on the board differ
from the names used to describe them. For the actual names check the TMS3 0-XDS100v3 board
itself.
3.1 Layout (top view)
Page 8 of 13

OLIMEX© 01 TMS3 0-XDS100v3 User's Manual
CHAPTER 4 NTERFACES AND HARDWARE
4. ntroduction to the chapter
In this chapter the connectors function will be pointed, the LEDs will be explained, as well as the
jumpers.
4.1 Connectors
There are five conectors on this board. 3 of them are explained below. The USB connector is type
mini and the small testpands for CT-RXD-GND-RTS-RXD-3/30V is named at the silk.
4.1.1 JTAG
The JTAG connector (note the one WITHOUT _14 appended) is used when the device is used as
adapter for older devices.
4.1.2 JTAG_14
Used for 14 pin JTAG connectoon.
4.1.3 JTAG_20
Used for 0 pin JTAG connectoon
4.2 LEDs
There are four leds on TMS3 0-XDS100v3. Two for indicating power input and power output and
two for the state of the jumpers.
4.2.1 Power LEDs
The PWR_LED shows whether the board is powered. The PWR_EN shows whether the board can
power the target.
Page 9 of 13

OLIMEX© 01 TMS3 0-XDS100v3 User's Manual
4.2.2 D3 and D4
The D3 and D4 leds show the state of, respectively, J4 and J5 jumpers.
4.3 Jumpers
There are two PTH jumpers on TNS3 0-XDS100v3. They are responsible for the emulation –
adapter configuration. When J4 and J5 are open – the chosen mode is emulator mode. When J4 an
J5 are closed the chosen mode is adapter.
Page 10 of 13

OLIMEX© 01 TMS3 0-XDS100v3 User's Manual
CHAPTER 5 REV S ON H STORY AND SUPPORT
5. ntroduction to the chapter
In this chapter you will find the current and the previous version of the document you are reading.
Also the web-page for your device is listed. Be sure to check it after a purchase for the latest
available updates and examples.
5.1 Document revision
Revision Changes Modified Page#
A,
10.09.12 Initial Creation All
B,
25.09.12
Fi ed several problems with links. Fi ed
the line numbers and the formatting of
the inde . Some other minor changes
3, 6, 7, 9, 12
Page 11 of 13

OLIMEX© 01 TMS3 0-XDS100v3 User's Manual
5.2 Useful web links and purchase codes
The web page you can visit for more info on your device is
https://www.olimex.com/Products/DSP/Emulators/TMS3 0-XDS100-V3/.
ORDER CODES:
TMS320-XDS100v3 – completely assembled and tested JTAG emulator
How to order?
You can order to us directly via our internet shop or from any of our distributors.
Check http://www.olimex.com/ or more in o.
Page 1 of 13

OLIMEX© 01 TMS3 0-XDS100v3 User's Manual
5.3 Product support
For product support, hardware information and error reports mail to: s[email protected]. Note
that we are primarily a hardware company and our software support is limited.
Please consider reading the paragraph below about the warranty of Olimex products.
Warranty and returns:
Our boards have lifetime warranty against manufacturing defects and
components.
During development work it is not unlikely that you can burn your programmer
or development board. This is normal, we also do development work and we have
damaged A LOT of programmers and boards during our daily job so we know how it
works. If our board/programmer has worked fine then stopped, please check if
you didn't apply over voltage by mistake, or shorted something in your target
board where the programmer was connected etc. Sometimes boards might get
damaged by ESD shock voltage or if you spill coffee on them during your work
when they are powered.
Please note that warrany do not cover problems caused by unproper use, shorts,
over-voltages, ESD shock etc.
If the board has warranty label it should be not broken. Broken labels void
the warranty, same applies for boards modified by the customer, for instance
soldering additional components or removing components - such boards will be
not be a subject of our warranty.
If you are positive that the problem is due to manufacturing defect or
component you can return the board back to us for inspection.
When we receive the board we will check and if the problem is caused due to
our fault and we will repair/replace the faulty hardware free of charge,
otherwise we can quote price of the repair.
Note that all shippings back and forth have to be covered by the customer.
Before you ship anything back you need to ask for RMA. When you ship back
please attach to it your shipping address, phone, e-mail, RMA# and brief
description of the problem. All boards should be sent back in antistatic
package and well packed to prevent damages during the transport.
Page 13 of 13