Olivetti d-Copia 52 User manual

42
52
COPIER OPERATION MANUAL
Cod. 506509D

PUBLICATION ISSUED BY:
Olivetti Tecnost, S.p.A.
Direzione Home/Office
Via Jervis, 77 - 10015 Ivrea (ITALY)
www.olivettilexikon.com
Copyright © 2001, Olivetti
All rights reserved
February 2001
The manufacturer reserves the right to carry out modifications to the product described in this manual at any time
and without any notice.
The ENERGY STAR program is an energy reduction plan introduced by theUnited States Environmental Protection
Agency in response to environmental issues and for the purpose of advancing the development and utilization of
more energy efficient office equipment.
ENERGY STAR is a U.S. registered mark.
The auto-shut-off time setting is between 15 and 120 minutes in the areas corresponding to the Swiss Energy 2000
Program area.
Your attention is drawn to the following actions which could compromise the conformity attested to above, as well
as the characteristics of the product:
•incorrect electrical power supply;
•incorrect installation, incorrect or improper use or use not in compliance with the warnings provided in the
User’s Manual supplied with the product;
•replacement of original components or accessories with others of a type not approved by the manufacturer, or
performed by unauthorised personnel.
The mark affixed to the product certifies that
the product satisfies the basic quality
requirements.
<Attention>
This instruction handbook is for the d-Copia 42 (42 ppm) and d-Copia 52 (52 ppm).
Specific matters for 52 ppm copier are covered on page 99 and thereafter.
The instruction is described based on the 42 ppm copier.

Please read the instruction handbook before using the copier. Keep it
close to the copier for easy reference.
COPIER OPERATION MANUAL
d-Copia 52
d-Copia 42

Please read the instruction handbook before using the copier.
Keep it close to the copier for easy reference.
The sections of this handbook and parts of the copier marked with symbols are safety
warnings meant to protect the user, other individuals and surrounding objects, and
ensure correct and safe usage of the copier. The symbols and their meanings are
indicated below.
DANGER: Indicates that serious injury or even death will very possibly result from
insufficient attention to or incorrect compliance with the related points.
WARNING: Indicates that serious injury or even death may result from insufficient
attention to or incorrect compliance with the related points.
CAUTION: Indicates that personal injury or mechanical damage may result from
insufficient attention to or incorrect compliance with the related points.
Symbols
The symbol indicates that the related section includes safety warnings. Specific
points of attention are indicated inside the symbol.
...........[General warning]
...........[Warning of danger of electrical shock]
...........[Warning of high temperature]
The symbol indicates that the related section includes information on prohibited
actions. Specifics of the prohibited action are indicated inside the symbol.
...........[Warning of prohibited action]
...........[Disassembly prohibited]
The ●symbol indicates that the related section includes information on actions which
must be performed. Specifics of the required action are indicated inside the symbol.
...........[Alert of required action]
...........[Remove the power plug from the outlet]
...........[Always connect the copier to an outlet with a ground connection]
Please contact your service representative to order a replacement if the safety warnings
in the handbook are illegible or if the handbook itself is missing. (fee required)

1
CONTENTS
CAUTION LABELS.......................................................................2
INSTALLATION PRECAUTIONS .................................................3
PRECAUTIONS FOR USE............................................................4
●MAKING FULL USE OF THE MACHINE’S ADVANCED
FUNCTIONS ......................................................................................5
NAMES OF PARTS...............................................................................7
(1) Main body.........................................................................................8
(2) Operation panel................................................................................9
(3) Basic screen on the touch panel ....................................................10
PREPARATIONS ................................................................................11
(1) How to load paper ..........................................................................11
1Loading paper into the drawers.................................................11
2Loading paper into the deck ......................................................12
3Loading paper into the stack bypass tray..................................12
SETTING ORIGINALS ........................................................................15
1Setting original(s) in the DF.......................................................15
2Setting original(s) on the platen ................................................16
BASIC OPERATION ..........................................................................17
●Basic copying procedure ............................................................17
FUNCTIONS........................................................................................19
(1) Enlargement/reduction ...................................................................19
1Auto magnification selection mode............................................19
2Zoom copy mode.......................................................................19
3Size zoom mode........................................................................19
4Standard zoom mode ................................................................20
5XY Zoom mode..........................................................................20
(2) Copy quality selection ....................................................................21
(3) Interrupt copying.............................................................................21
(4) Duplex copying from various originals [Duplex copy].....................22
(5) Making a margin space for binding [Margin mode].........................24
(6) Printing page numbers to copy [Print page numbers] ....................26
(7) Copying two-page originals as separate pages [Split copy]...........27
(8) Making copies with clean edges [Border erase].............................28
(9) Making covers or insert sheets among the copies
[Sheet insertion copy] .....................................................................29
1Submodes .................................................................................29
2Combination of modes...............................................................31
3How to make copies in the sheet insertion mode......................32
(10) Making copies onto transparencies [Presentation mode].............34
(11) Feeding a paper as a transparency + backing sheet mount
[Transparency backing mode]......................................................36
(12) Making image overlay [Form overlay]...........................................37
(13) One copy from two or four originals [Merge copy]........................38
(14) Booklet from book originals [Booklet + cover copy mode]............39
(15) Weekly magazine from duplex/one-sided originals
[Booklet copy]...............................................................................40
(16) Copying and stitching into booklet (sheet originals)
[Stitching mode]............................................................................41
(17) Inverting black and white [Invert copy] .........................................43
(18) Making mirror image copies [Mirror image copy]..........................44
(19) Sorting automatically [Sort copy]..................................................44
(20) Memorizing frequency used settings [Program mode].................45
1How to register settings...........................................................45
2Calling up a program...............................................................46
(21) Recall mode..................................................................................46
(22) Setting change function................................................................47
(23) Rotate copy ..................................................................................48
(24) Energy saver function...................................................................48
(25) Auto shut-off function....................................................................48
APPLICABLE COPY MODES.............................................................49
(1) Reserving another copy while copying is performed [Add Job]......49
1Add job ......................................................................................49
2Changing the setting contents of the add job ...........................50
3Clearing the add job ..................................................................51
4Changing the add job order.......................................................51
(2) Copying various originals at a time [Job build function]..................52
1Memory copy from DF and platen .............................................52
●Large quantity of originals...........................................................52
●Auto size.....................................................................................52
●Choose size................................................................................52
2Duplex copies from one-sided and duplex mixed originals .......55
●Finishing like originals [Print as original].....................................55
●Duplex copies from all originals [Duplex all originals] ................55
●Copying desired page on the front side [Chapterize]..................55
3Batch copy from platen..............................................................57
●Only sheet originals....................................................................57
●Only book originals.....................................................................57
●Sheet & book originals................................................................57
COPIER MANAGEMENT....................................................................61
(1) Copy management.........................................................................61
1About the copy management mode...........................................61
2How to make settings in the copy management mode..............61
3How to make the various settings..............................................62
●Registering new ID-codes...........................................................62
●Deleting ID-codes.......................................................................63
●Altering limits .............................................................................64
●Clearing copy counts..................................................................64
●Viewing copy counts...................................................................65
●Printing of copy management report...........................................65
●Turning copy management ON/OFF ..........................................66
4Making copies when copier is in copy management mode .......66
(2) Week timer .....................................................................................67
1About the timer function.............................................................67
2How to make settings in the timer mode ...................................67
3How to make settings for the various functions.........................68
●Setting the time...........................................................................68
●Programming the week timer......................................................68
●Cancelling the timer function ......................................................69
●Turning the timer ON/OFF .........................................................70
4Making copies after copier has been stopped by timer .............70
(3) The default settings........................................................................70
●Copy default setting.......................................................................71
●How to make settings in the copy default setting mode..............72
1EXPOSURE MODE...................................................................72
2EXPOSURE STEPS..................................................................72
3TONER ECONOMY MODE.......................................................72
4AUTO EXPOSURE ADJUSTMENT ..........................................73
5MANUAL EXPOSURE ADJUSTMENT......................................73
6QUALITY ...................................................................................73
7OUTPUT FORM ........................................................................73
8PAPER SELECTION.................................................................73
9JOB PROGRAMMING...............................................................73
0DEFAULT DRAWER .................................................................74
!ZOOM MODE............................................................................74
@SET COPY LIMIT WITH #-KEYS ..............................................74
#CUSTOM SIZE FOR BORDER ERASE....................................74
$F&B P. MARGIN........................................................................74
%DRAWER FOR INSERT SHEET...............................................75
^DRAWER FOR COVER SHEET/STITCH .................................75
&ROTATE SORT.........................................................................75
*CREATE SHORTCUT (#1, #2) .................................................75
(CREATE USER CHOICE #1 - #5..............................................75
●How to finish the copy default setting.........................................75
●Machine default setting .................................................................76
●How to set the machine default setting mode.............................77
1UN-FIXED SIZE FROM BYPASS..............................................77
2AUTOMATIC DRAWER SWITCHING.......................................78
3PAPER SIZE .............................................................................78
4SPECIAL PAPER ......................................................................78
5APS FOR SPECIAL PAPER .....................................................79
6KEY SOUND ON/OFF...............................................................79
7AUTO PREHEAT TIME.............................................................79
8AUTO SHUT-OFF TIME............................................................79
9CHANGE MANAGEMENT CODE WITH #-KEYS.....................79
0AUTO SHUT-OFF......................................................................80
●How to finish the machine default setting...................................80
(4) LANGUAGE OF TOUCH PANEL...................................................80
OPTIONAL EQUIPMENT....................................................................81
(1) a. Finisher.......................................................................................81
b. Booklet stitcher...........................................................................81
(2) Key counter ....................................................................................82
(3) I/F kit...............................................................................................82
(4) Memory copy board........................................................................82
MESSAGES.........................................................................................83
●When the messages below are displayed:.................................83
REPLACING THE TONER CARTRIDGE............................................85
WHEN PAPER MISFEEDS .................................................................86
(1) Misfeed location indicators.............................................................86
(2) Cautions .........................................................................................86
(3) Removal procedures ......................................................................87
TROUBLESHOOTING ........................................................................95
CLEANING THE COPIER ...................................................................97
SPECIFICATIONS...............................................................................98
ABOUT 52 PPM COPIER....................................................................99

2
CAUTION LABELS
Caution labels have been attached to the copier at the following locations for safety
purposes. BE SUFFICIENTLY CAREFUL to avoid fire or electric shock when
removing a paper jam or when replacing toner.
Label 4, 5
High temperature inside. Do not
touch parts in this area, because
there is a danger of getting
burned. ........................................
Label 3
High temperature inside. Do not
touch parts in this area, because
there is a danger of getting
burned. ........................................
Label 1
High voltage inside. NEVER
touch parts in this area, because
there is a danger of electric
shock. .........................................
NOTE: DO NOT remove these labels.
Label 2
High voltage inside. NEVER
touch parts in this area, because
there is a danger of electric
shock. .........................................

3
INSTALLATION PRECAUTIONS
■Environment
CAUTION
• Avoid placing the copier on or in locations which are
unstable or not level. Such locations may cause the
copier to fall down or fall over. This type of situation
presents a danger of personal injury or damage to the
copier.............................................................................
• Avoid locations with humidity or dust and dirt. If dust
or dirt become attached to the power plug, clean the
plug to avoid the danger of fire or electrical shock. .......
• Avoid locations near radiators, heaters, or other heat
sources, or locations near flammable items, to avoid
the danger of fire............................................................
• To keep the copier cool and facilitate changing of parts
and maintenance, allow access space as shown
below.
Leave adequate space, especially around the left
cover, to allow air to be properly ventilated out of the
copier. ...........................................................................
• Always use the caster stoppers to stabilize the copier
once it is in place to keep it from moving and/or falling
over and causing injury..................................................
Other precautions
• Adverse environmental conditions may affect the safe
operation and performance of the copier. Install in an
air-conditioned room (recommended room
temperature: around 20°C, humidity: around 65%RH)
and avoid the following locations when selecting a site
for the copier.
. Avoid locations near a window or with exposure to
direct sunlight.
. Avoid locations with vibrations.
. Avoid locations with drastic temperature fluctuations.
. Avoid locations with direct exposure to hot or cold air.
. Avoid poorly ventilated locations.
■Power supply/Grounding the copier
WARNING
• DO NOT use a power supply with a voltage other than
that specified. Avoid multiple connections in the same
outlet. These types of situations present a danger of
fire or electrical shock....................................................
• Plug the power cord securely into the outlet. If metallic
objects come in contact with the prongs on the plug, it
may cause a fire or electric shock.................................
• Always connect the copier to an outlet with a ground
connection to avoid the danger of fire or electrical
shock in case of an electric short. If an earth
connection is not possible, contact your service
representative. ..............................................................
Other precautions
• Connect the power plug to the closest outlet possible
to the copier.
■Handling of plastic bags
WARNING
• Keep the plastic bags that are used with the copier
away from children. The plastic may cling to their
nose and mouth causing suffocation.............................

4
PRECAUTIONS FOR USE
■Cautions when using the copier
WARNING
• DO NOT place metallic objects or containers with
water (flower vases, flower pots, cups, etc.) on or near
the copier. This type of situation presents a danger of
fire or electrical shock should they fall inside.................
• DO NOT remove any of the covers from the copier as
there is a danger of electrical shock from high voltage
parts inside the copier....................................................
• DO NOT damage, break or attempt to repair the power
cord. DO NOT place heavy objects on the cord, pull it,
bend it unnecessarily or cause any other type of
damage.
These types of situations present a danger of fire or
electrical shock..............................................................
• NEVER attempt to repair or disassemble the copier or
its parts as there is a danger of fire, electrical shock or
damage to the laser. If the laser beam escapes, there
is a danger of it causing blindness.................................
• If the copier becomes excessively hot, smoke appears
from the copier, there is an odd smell, or any other
abnormal situation occurs, there is a danger of fire or
electrical shock. Turn the main switch OFF (O)
immediately, remove the power plug from the outlet
and contact your service representative........................
• If anything harmful (paper clips, water, other fluids,
etc.) falls into the copier, turn the main switch OFF (O)
immediately. Next, remove the power plug from the
outlet to avoid the danger of fire or electrical shock.
Then contact your service representative. ....................
• DO NOT remove or connect the power plug with wet
hands, as there is a danger of electrical shock. ............
• ALWAYS contact your service representative for
maintenance or repair of internal parts..........................
CAUTION
• DO NOT pull the power cord when removing it from
the outlet. If the power cord is pulled, the wires may
become broken and there is a danger of fire or
electrical shock. (ALWAYS grasp the power plug
when removing the power cord from the outlet.) ...........
• ALWAYS remove the power plug from the outlet when
moving the copier. If the power cord is damaged,
there is a danger of fire or electrical shock....................
• If the copier will not be used for a short period of time
(overnight, etc.), turn the main switch OFF (O).
If it will not be used for an extended period of time
(vacations, etc.), remove the power plug from the
outlet for safety purposes during the time the copier is
not in use. .....................................................................
• ALWAYS hold the designated parts only when lifting or
moving the copier. .........................................................
• For safety purposes, ALWAYS remove the power plug
from the outlet when performing cleaning operations....
• If dust accumulates within the copier, there is a danger
of fire or other trouble. It is therefore recommended
that you consult with your service representative in
regard to cleaning of internal parts. This is particularly
effective if accomplished prior to seasons of high
humidity. Consult with your service representative in
regard to the cost of cleaning the internal parts of the
copier.............................................................................
• DO NOT leave the document feeder open as there is a
danger of personal injury...............................................
Other precautions
• DO NOT place heavy objects on the copier or cause
other damage to the copier.
• DO NOT open the front cover, turn off the main switch,
or pull out the power plug during copying.
• During copying, some ozone is released, but the
amount does not cause any ill effect to one's health. If,
however, the copier is used over a long period of time
in a poorly ventilated room or when making an
extremely large number of copies, the smell may
become unpleasant. To maintain the appropriate
environment for copy work, it is suggested that the
room be properly ventilated.
• When lifting or moving the copier, contact your service
representative.
• DO NOT touch electrical parts, such as connectors or
printed circuit boards. They could be damaged by
static electricity.
• DO NOT attempt to perform any operations not
explained in this handbook.
• CAUTION: Use of controls or adjustments or
performance of procedures other than those specified
herein may result in hazardous radiation exposure.
■ Cautions when handling
consumables
CAUTION
• Avoid inhalation, ingestion, skin or eye contact. If
ingestion occurs, dilute stomach contents thoroughly
with water and seek medical treatment. If skin contact
occurs, wash with soap and water. If contact with eyes
occurs, flush thoroughly with water and seek medical
treatment........................................................................
• Prolonged inhalation of excessive dusts may cause
lung damage. Use of this product, as intended, does
not result in inhalation of excessive dusts. ...................
• Keep away from children...............................................
• Do not incinerate toner and toner containers.
Dangerous sparks may cause burn...............................
Other precautions
• Always read the safety instructions which are included
in the box or printed on the container when handling
consumables.
• Dispose of the toner or toner containers in accordance
with Federal, State and Local rules and regulations.
• Store consumables in a cool, dark location.
• If the copier will not be used for an extended period of
time, remove the paper from the cassette, return it to
its original package and reseal it.

5
●MAKING FULL USE OF THE MACHINE'S ADVANCED FUNCTIONS
Making the machine automatically
select paper of the same size as the
original
<Auto paper selection mode>
(page 17)
Various functions for making
enlarged and reduced copies
■Enlarging/reducing copies to a
specified drawer size
<Auto magnification selection
mode> (page 19)
■Enlarging/reducing copies to any desired
size in the range
25-400% <Zoom copy mode > (page 19)
■Selecting the zoom ratio by one-touch key
<Size zoom mode> (page 19) ■Enlarging/reducing copies to specify sizes of the original and paper
<Standard zoom mode> (page 20)
■Enlarging/reducing length and width
separately
<XY zoom mode> (page 20)
Making clear reproductions of
photographs
<Copy quality selection> (page 21)
Copying to front and back of the
paper from various originals
<Duplex copy> (page 22)
Making a margin in the copies, for
binding, etc.
<Margin mode> (page 24)
Printing page numbers on copies
<Print page numbers> (page 26) Copying two-pages originals onto separate sheets
<Split copy > (page 27)
Making copies with clean edges
<Border erase> (page 28)
Making covers or insert sheets
among the copies
<Sheet insertion copy> (page 29)
Making documents with
transparencies
<Presentation mode> (page 34)
Feeding a paper as a transparency +
backing sheet mount
<Transparency backing mode>
(page 36)
1
543
876
11109
2

A full range of optional
equipment is available
■Finisher (page 81)
6
Making image overlay
<Form overlay> (page 37) Making one copy from two or four originals
<Merge copy> (page 38)
Making booklet from book originals
<Booklet + cover copy mode>
(page 39)
<Stitching mode>
(page 41)
Sorting automatically
<Sort copy> (page 44) Changing the direction of the sheets for easy sorting
<Rotate sort copy> (page 44)
Inverting black and white
<Invert copy> (page 43)
Making mirror image copies
<Mirror image copy> (page 44) Memorizing frequently used settings <Program mode> (page 45) Copying various originals at a time
<Job build function> (page 52)
Managing the number of copies
made by different departments, with
ID-code
<Copy management mode>
(page 61)
Turning main switch ON/OFF
automatically
<Week timer> (page 67)
Changing the language used for
messages
<Language selection function>
(page 80)
232221
201918
171615
141312
24
■Key counter
(page 82) ■I/F kit (page 82) ■Memory copy board (page 82)
●MAKING FULL USE OF THE MACHINE'S ADVANCED FUNCTIONS
■Booklet stitcher
(page 81)

7
NAMES OF PARTS

8
(1) Main body
1Platen
(Set a book original or the like that cannot be set in the DF
on this.)
2Original size indicator lines
(Be sure to align the original with these when setting the
original on the platen.)
3Operation panel
(Operate to copy here.)
4Stack bypass tray
(Load paper here when copying onto small-size paper or
colored paper.)
5Insert guides
(Be sure to match the paper size when loading paper on the
stack bypass tray.)
6Support guide
(Pull out when copying onto A4 (vertical) or larger paper.
7Front cover
(Open to replace a toner cartridge or for misfeed removal.)
8Right cover
(Open when paper misfeed occurs in the paper feed
section.)
9Duplex unit
0Re-feeding section
(Open when paper misfeed occurs in the duplex unit.)
!Duplex cover
(Open when paper misfeed occurs in the duplex unit.)
@Drawer 1
(Holds up to 550 sheets of standard paper.)
#Length adjustment lever
$Width adjustment lever
%Drawer 2
(Holds up to 550 sheets of standard paper.)
^DF original reversing cover
(Open when paper misfeeds in DF section.)
&Original set indicator
(The original condition is displayed.
Green lights: The original is set. Copying will begin by
pressing the Start key.
Green blinks: The original is not set securely. Reset the
original.
Red blinks: Originals are misfed. Remove all misfed
originals in accordance with page 93.)
*Original insertion guide
(Set to match the size of the original when setting in the
DF.)
(Original table
(Set the DF original on this table.)
)DF opening/closing lever
(Hold when opening and closing the DF.)
⁄Original ejection cover
(The copied originals are stored here.)
¤Paper ejection guide
(Open when setting an original of B4 or larger in the DF.)
‹Main switch
(Turn ON ( | ) before starting machine.)
›Left cover
(Open when paper misfeed occurs in the fixing unit or
ejection section.)
fiCopy tray
(Completed copies will be ejected here.)
flToner cartridge
‡Toner cartridge release lever
(Operate when replace a toner cartridge.)
°Paper transfer section release button
·Paper transfer section handle
‚Paper transfer section release lever
(Operate when paper misfeed occurs in the paper transfer
section.)
Paper feed section knob
(Operate to remove paper misfed in paper feed section.)
„Fixing unit
´Fixing unit handle
(Pull out the fixing unit to remove paper misfed in fixing unit
by handling this.)
‰Fixing knob
(Operate to remove paper misfed in fixing unit.)
ˇFixing unit release lever
(Operate to open/close fixing unit.)
ÁHandles for transport
(Pull out to be handle. They are located in four positions.)
<In case of using drawer-type paper feed desk>
¨Drawer 3
(Holds up to 550 sheets of standard paper.)
ˆDrawer 4
(Holds up to 550 sheets of standard paper.)
ØDesk right cover
(Open when paper misfeed occurs.)
<In case of using deck-type paper feed desk>
∏Paper feed deck
(Holds up to 3,000 sheets of standard paper.)
ÅRight deck cover
(Open when paper misfeed occurs.)
NAMES OF PARTS

&Start key
*Start indicator
(When this lights green, the copier is ready to copy.)
(Reset key (See "●Initial mode")
)Auto selection key (page 16)
⁄Auto selection indicator
(Lights when auto selection mode is selected.)
¤Energy Saver key (page 48)
‹Energy Saver indicator
(Lights when the copier is in the rest state because it is in
the preheat time or week timer is operative.)
›Interrupt key (page 21)
fiInterrupt indicator
(Lights when interrupt mode is selected.)
●Initial mode (at the end of warm-up or when the Reset key
is pressed)
In the initial mode, the copying mode set is the "auto paper
selection mode" that paper of the same size as the original is
selected automatically, the number of copies set is "1", and
"manual exposure mode" is set for copy exposure.
* It is also possible to set auto exposure mode in the initial
mode. (See page 72, "1EXPOSURE MODE".)
●Auto clear function
About 90 seconds after copying stops, the copier will
automatically return to the same settings as those after warm
up. (However, the exposure mode will not change.) Copying
can be performed continuously in the same settings of copy
mode, number of copies, and exposure if copying is started
before the auto clear function operates.
●Automatic drawer switching function
If two drawers contain the same size of paper and the paper in
one drawer runs out during copying, this function switches to
feeding paper from the other drawer.
* The automatic drawer switching function can be disabled.
(See page 78, "2AUTOMATIC DRAWER SWITCHING")
(2) Operation panel
1Punch mode key (page 81)
(Press to punch with the optional finisher.)
2Punch mode indicators
3Staple sort mode key (page 81)
(Press to select the stapling position with the optional
finisher.)
4Staple sort mode indicators
5Sorter mode key (page 44)
(Press to select the sorter mode.)
6Sort mode indicator
7Group mode indicator
8Brightness adjustment control
(Use to adjust the brightness of the touch panel.)
9Data indicator
(This indicator lights, and blinks while the optional printer
function is being used.)
0Program key
(Press to use the job programming.)
!Manual key
(Press to make copying of same ratio, regardless of the
original size.)
@Add job key (page 49)
#Copier/Printer switching key
(Press when switching the copy mode and printer mode, if
optional I/F kit is installed.)
$Touch panel
(Number of copies, machine status, operations, etc., appear
on this panel. By gently touching these keys, items, settings,
and so on can be selected. Do not press on the keys with
wooden, metal or other hard objects, and do not prick them
with pointed objects. In this handbook, touch key names are
indicated by quotation marks.)
%Numeric keys
(Press to set the number of copies and enter the value.)
^Stop/Clear key
(Press to stop copying or to change the number of copies to
be made.)
9
NAMES OF PARTS

1"BASIC" key
(Touch to return to the basic screen.)
2"ZOOM" key
(Touch to change the copy zoom ratio. Page 19)
3"FUNCTION" key
(Touch to select the copy function. Function selection
screen will appear.)
4"SPECIAL" [Management mode] key
(Touch to alter the language used for the messages or set
the week timer, etc. Management mode setting screen will
appear.)
5Message display
(Displaying messages on how to operate the machine and
indications of the machine's status.)
6Copy number display
(At start and end of copying, displaying the number of
copies set. During copying, displaying the number of copies
completed.)
7Copy mode/zoom ratio display
(The selected copy mode and copy zoom ratio will appear.)
8Paper size keys/indicators
(The paper size set in each of the drawers will appear.
Also, touch this key to select the paper feed drawer. The
selected drawer will be highlighted.)
9"DUPLEX" key
(Touch to set the duplex copying. The duplex copy setting
screen will appear. Page 22)
0"JOB BUILD" key
(Touch to use the job build function. The setting screen will
appear. Page 52)
!Copy quality mode selection keys
(Touch to select the "MIXED", "TEXT" and "PHOTO"
modes according to the type of originals. The highlighted
key is the mode being selected at present. Page 21)
@"AUTO" [Auto/manual exposure selection] key
(Touch to switch the auto exposure mode and manual
exposure mode. When it is highlighted, auto exposure
mode is operating. In the manual exposure mode, the scale
will appear on the display.)
#Copy exposure mode keys
(Touch to adjust copy mode manually.)
$Copy exposure scale
(Appears in the manual exposure mode. Move the
exposure scale to the right to make copies darker, and
move it to left to make copies lighter. 7 or 13 exposure
levels can be set. See page 72, "2EXPOSURE STEPS".)
%"Eco" key
Touch to enter the toner economy mode. When this key is
highlighted, the exposure level will become low and toner
consumption will be reduced. Use this mode for trial printing
or the like that does not require high quality printing.
10
(3) Basic screen on the touch panel
NAMES OF PARTS

(1) How to load paper
In the drawer-type paper feed desk, paper can be loaded at a total 5 points-- the 4
drawers and the stack bypass tray. In the deck-type paper feed desk, paper can be
loaded at a total 4 points-- the 2 drawers, the deck and stack bypass tray.
1Loading paper into the drawers
Paper can be loaded into the drawers at the front of the copier. Each drawer holds
up to 550 sheets of standard (80 g/m2) or colored paper.
The drawer can be set to hold paper of any desired size from A3 to A5R.
1. Pull the drawer out toward you as far as it will go.
* Not to pull more than one drawer out at the same time.
2. Turn the width adjustment lever to align the width guide with the paper's width.
3. Turn the length adjustment lever to align the length guide with the paper's length.
* A sticker indicates how high paper can be loaded. Do not exceed the limits on the
sticker.
* When loading paper into the drawer, make sure the copy side is facing downward.
(The copy side is the side facing upward when the package is opened.)
4. Set the paper against the right-hand wall of the drawer, and position the paper
so that it is aligned with the correct size indicator lines (marked on the bottom of
the drawer) for its size.
11
PREPARATIONS

12
PREPARATIONS
A4
A5
A3
A4
* Set a paper size label sheet in the front of the drawer to see the paper size.
5. Gently push the drawer back in.
* Set the paper size referring "3PAPER SIZE" on page 78.
2Loading paper into the deck
For the deck, A4 sheets of standard paper (80 g/m2) can be loaded in two rows. Up
to the 1,500 sheets each, and therefore 3,000 sheets can be loaded.
1. Pull out the deck out toward you as far as it will go.
2. Load the paper in two rows.
* A sticker indicates how high paper can be loaded. Do not exceed the limits on
the sticker.
* When loading paper into the deck, make sure the copy side is facing
downward. (The copy side is the side facing upward when the package is
opened.)
3. Gently push the deck back in.
* When the copier is out of use for a prolonged period of time, remove the paper
from the drawer(s), put it into its original packaging, and seal it, to protect it
against moisture.
3Loading paper into the stack bypass tray
The stack bypass can hold up to 100 sheets of standard paper (80 g/m2) at a time.
The paper can be any size from A3 to A6R, Folio. When copying onto special
paper, always use this tray to feed the paper.
* When using custom size paper, paper size can be specified. Set the paper size in
accordance with the following procedure in the "●How to set the custom sizes"
on page 77.

* The types of special paper and the number of sheets which can be loaded in this
tray are:
• Tracing paper: 1 sheet
• Transparencies: 25 sheets (When set transparency, fan transparencies before
setting them.)
• Letterheads: 100 sheets
• Colored paper: 100 sheets
• Standard paper (120 g/m2, 160 g/m2): 25 sheets
* When copying onto tracing paper or transparencies, set the original on the platen.
PREPARATIONS
1. Open the stack bypass tray.
* To load A4 (vertical) or larger size paper, pull out the support guide.
2. Adjust the insert guides to fit the size of the paper to be loaded.
3. Insert the paper all the way in, along the guides, as far as it will go.
* When loading paper into the multi-bypass, make sure the copy side is facing
upward. (The copy side is the side facing upward when the package is
opened.)
●Setting the envelops in the stack bypass tray
When using the optional printer function, the envelops can be set in the stack
bypass tray.
The types of the envelop can be used are COM-10, Monarch, DL and C5, and up
to 10 envelops can be set at a time.
1. Open the stack bypass tray.
13

14
PREPARATIONS
2. Align the insert guides with the envelop size.
3. Open the envelops and set the side to be printed face up, and set the opening
part of the envelop in the right side and insert them until stop aligning with the
insert guide.
* Incorrect setting may cause paper misfeed, printing in the different direction or
printing on the different side.
* Set the envelop size in accordance with the following procedure in the "● How
to set the custom sizes" on page 77.

1Setting original(s) in the DF
The copier is equipped with the DF (document feeder).
Multiple sheet originals loaded into the DF automatically fed one by one. The DF
automatically turns over duplex originals for copying on the reverse side.
SETTING ORIGINALS
Originals that can be loaded in the DF
• Sheets originals
• Thickness: One-sided originals: between 35 g/m2- 160 g/m2
Duplex originals: between 50 g/m2- 120 g/m2
• Size: Max. A3 to Min. A5 (vertical)
• Capacity: 70 sheets (A4 or smaller size, 80 g/m2)
50 sheets (B4 or larger size, 80 g/m2)
(However, 50 sheets when using auto selection mode)
Notes
Do not use originals of the kinds listed below.
When using perforated sheets or sheets with punch holes, do not insert the end
with the perforations or holes first.
• Transparencies
• Carbon paper, crumpled originals, those with strong folds or soft originals such as
vinyl
• Originals which are not rectangular, wet originals, sheets with adhesive tape or
glue
• Original with clips or staples (To use such originals, remove clips or staples and
straighten the crumpled or folded originals before setting them.)
• Clipping or sheets with very slippery surfaces
• Originals with wet correcting fluid
• Originals with folds (When such originals must be used, smooth out the folded
portion before setting them.)
1. Adjust the original insert guides to fit the size of the original.
* Check if any ejected originals are left on the original ejection cover before
setting the originals. If any originals are left on the original ejection cover,
original misfeeds may occur.
2. Arrange the originals in order and set them face up (front face up for duplex
originals) on the original table. The original set indicator lights green. If the
indicator does not light, reset the originals.
* The originals must not exceed the scale pasted on the rear original insert guide. If
excessive originals are set, the original misfeeds may occur.
15

16
SETTING ORIGINALS
* When setting A3, Folio and B4 originals, open the ejection guide to avoid originals
from dropping.
* When copying duplex originals, originals will be ejected temporarily from the DF
original reversing cover for reversing. Do not touch the originals at this time. If the
originals are pulled out by force, the original misfeeds may occur.
●Auto selection mode
The size of each originals is detected to copy to the paper of the same size as each
original.
* Up to 50 sheets can be loaded in DF in this mode.
* A3 and A4 originals can be set in this mode and only the originals of the same
size in width can be used.
• How to set auto selection mode
Press the auto selection key on the operation panel to light the auto selection
indicator.
2Setting original(s) on the platen
For original(s) that cannot be set in the DF, such as a book and magazine, open
the DF main body to set the original on the platen.
1. Hold the DF opening/closing lever to open the DF.
* When opening the DF, check if no original is on the original table and original
ejection cover. Otherwise, it may fall down when the DF is opened.
2. Set the original(s).
Face down the originals on the platen and align them with original size indicator.
3. Hold the DF opening/closing lever to close the DF.
* At this time, avoid pressing the platen excessively. The platen may be broken.
CAUTION
DO NOT leave the document feeder open as there is a danger of
personal injury.