Olivetti d-COLOR P3100 User manual

d-COLOR P3100
MAINTENANCE/TROUBLESHOOTING

d-COLOR P3100 Contents-1
Table of contents
1 Cleaning this Machine
1.1 Before getting started .................................................................................................................... 1-3
1.2 Cleaning ........................................................................................................................................... 1-5
1.2.1 Cleaning the outside of this machine..................................................................................................1-5
Control Panel ..................................................................................................................................... 1-5
Exhaust Air Duct ................................................................................................................................ 1-5
Outer Covers...................................................................................................................................... 1-5
1.2.2 Cleaning the Paper Feed Rollers ........................................................................................................1-6
Cleaning the Paper Feed Rollers of the Manual Feed Tray ............................................................... 1-6
Cleaning the Paper Feed Rollers of Tray 1/2..................................................................................... 1-7
Cleaning the Transport Roller of Tray 2 ............................................................................................. 1-7
1.2.3 Cleaning the Laser Lenses..................................................................................................................1-8
2 Checking and Replacing Consumables
2.1 Checking the status of consumables............................................................................................ 2-3
Consumables replacement messages............................................................................................... 2-3
2.2 Replacing consumables ................................................................................................................. 2-4
2.2.1 Replacing a Toner Cartridge...............................................................................................................2-4
Handling a Toner Cartridge................................................................................................................ 2-4
Storing Toner Cartridges.................................................................................................................... 2-4
Replacement procedure .................................................................................................................... 2-5
2.2.2 Replacing an Imaging Unit..................................................................................................................2-9
2.2.3 Replacing a Waste Toner Bottle .......................................................................................................2-15
2.2.4 Replacing the Transfer Roller............................................................................................................2-17
2.2.5 Replacing the Transfer Belt Unit.......................................................................................................2-19
2.2.6 Replacing a Fuser Unit......................................................................................................................2-23
3 Clearing a Paper Jam
3.1 To prevent a paper jam .................................................................................................................. 3-3
3.2 When a paper jam has occurred ................................................................................................... 3-4
3.2.1 Paper jam message screen.................................................................................................................3-4
3.2.2 Clearing a paper jam in the Manual Feed Tray or Transfer Roller ......................................................3-4
Clear procedure ................................................................................................................................. 3-5
3.2.3 Clearing a paper jam in Tray 1 ............................................................................................................3-6
Clear procedure ................................................................................................................................. 3-7
3.2.4 Clearing a paper jam in Tray 2 ............................................................................................................3-9
3.2.5 Clearing a paper jam in the Duplex Option.......................................................................................3-10
3.2.6 Clearing a paper jam in the Fuser Unit .............................................................................................3-11
Clear procedure ............................................................................................................................... 3-11
3.3 Troubleshooting for paper jam .................................................................................................... 3-15
4 Troubleshooting
4.1 The power is not turned on ............................................................................................................ 4-3
4.2 When the Message Window is not displayed............................................................................... 4-3
4.3 Cannot print..................................................................................................................................... 4-4
4.3.1 Cannot print ........................................................................................................................................4-4
4.3.2 Problems on print quality....................................................................................................................4-6
4.3.3 When the bit count does not match between the server and the client .............................................4-8
4.4 Major messages and actions......................................................................................................... 4-9
Warning messages............................................................................................................................. 4-9

Contents-2 d-COLOR P3100
Error messages ................................................................................................................................ 4-10
Service call....................................................................................................................................... 4-10
5 Checking Counters
5.1 Checking the counter ..................................................................................................................... 5-3
6Index

1Cleaning this Machine

d-COLOR P3100 1-3
1.1 Before getting started 1
1 Cleaning this Machine
NOTICE
Thoroughly read all the precautions and warning labels, and be sure to follow their instructions. These labels
are provided inside the door of this machine or inside the machine.
1.1 Before getting started
Carefully handle this machine so that you can use it for an extended period of time. A failure caused by in-
correct use or rough handling is not covered by the warranty
If dust or slips of paper are left inside or outside this machine, it may reduce printing quality. We recommend
that you periodically clean this machine. Follow the guideline shown below.
-When cleaning the inside of this machine or clearing a paper jam, exercise care not to touch around the
Fuser Unit because internal components such as the Fuser Unit may be hot.
-Do not place any objects on this machine.
-To clean this machine, use a soft cloth.
-Do not spray detergent directly on the surface of this machine. If detergent gets into this machine
through holes, slots, etc., it may damage internal circuits.
-Do not use abrading or corrosive agents, including solvents such as alcohol, benzene, or thinner, to
clean this machine.
-When using detergent such as neutral detergent, try it on an obscure part of this machine to check its
effectiveness.
-To clean this machine, do not use a sharp or textured object such as a wire, plastic cleaning pad, or
brush.
-When you close the door of this machine, do it carefully. Do not do anything that might make this ma-
chine oscillate.
-Do not cover this machine directly after using it. Turn the power off, then wait until this machine be-
comes cool.
-Do not leave the door of this machine open for a long period of time. Especially, in bright light, Imaging
Unit may be damaged.
-Do not open any door of this machine during printing.
-Do not align sheets of paper at the top of this machine.
-Do not grease or disassemble this machine.
-Do not set this machine on an incline.
-Do not touch the electric wiring, gears, or laser beam unit. Doing so may lead to a machine failure or
reduce printing quality.
-Do not load an excessive number of sheets of paper in the output tray. Doing so may cause a paper
jam or paper curling.
-When moving this machine, at least two people are required to do so. To prevent toner from spilling,
keep this machine horizontal when carrying it.

1-4 d-COLOR P3100
Before getting started
11.1
-When carrying this machine, be sure to fold the Manual Feed Tray and hold the parts shown below.
-When the optional Lower Feeder Unit is installed, be sure to carry it separately from this machine. Also,
do not hold handles (drawers) of the Lower Feeder Unit or Right Door. Doing so may damage the Low-
er Feeder Unit.
-Before connecting the power cable of this machine to the power outlet, check that internal components
removed at the time of cleaning have been installed to their original positions.
-If your hand is stained by toner, wash it with cool water and neutral detergent.
7WARNING
-Before cleaning this machine, turn the power off, then disconnect the power cable and interface cable.
Exercise care not to spill water or detergent inside this machine. Doing so may cause a damage of this
machine or an electric shock.
7CAUTION
-When moving this product, be sure to hold the places specified in the user's guide and other guidance
information. Not doing so may cause injuries due to the product being dropped.
-If any toner enters your eyes, immediately wash them with cool water, then contact your doctor.
-The Fuser Unit is heated. The temperature of the Fuser Unit slowly reduces (wait for 1 hour).
28.3kg
62.4 lbs

d-COLOR P3100 1-5
1.2 Cleaning 1
1.2 Cleaning
7WARNING
-Before cleaning this machine, turn the power off, then disconnect the power cable and interface cable.
Exercise care not to spill water or detergent inside this machine. Doing so may cause a damage of this
machine or an electric shock.
1.2.1 Cleaning the outside of this machine
Control Panel
Exhaust Air Duct
Outer Covers

1-6 d-COLOR P3100
Cleaning
11.2
1.2.2 Cleaning the Paper Feed Rollers
If the Paper Feed Rollers have been stained with paper powders or dust, a paper feeding failure may occur.
Cleaning the Paper Feed Rollers of the Manual Feed Tray
1Open the Manual Feed Tray.
2Press up the center of the flip-top plate until the lock latches (white) at the right and left are locked.
3Wipe off the Paper Feed Rollers with a soft and dry cloth.
4Close the Manual Feed Tray.

d-COLOR P3100 1-7
1.2 Cleaning 1
Cleaning the Paper Feed Rollers of Tray 1/2
0Tray 2 is available when the optional Lower Feeder Unit is installed.
1Open the tray.
2Wipe off the Paper Feed Rollers with a soft and dry cloth.
3Close the Tray.
Cleaning the Transport Roller of Tray 2
0Tray 2 is available when the optional Lower Feeder Unit is installed.
1Open the Right Door of Tray 2.
%When opening the Right Door of Tray 2, be sure to fold the Manual Feed Tray in advance.
2Wipe off the Transport Roller with a soft and dry cloth.
3Close the Right Door of Tray 2.

1-8 d-COLOR P3100
Cleaning
11.2
1.2.3 Cleaning the Laser Lenses
This machine has four laser lenses. Follow the steps shown below to clean all the laser lenses.
0The Laser Lens Cleaning Tool is stored in the Tray 1.
1Pull out Tray 1.
2Remove the cover.
%The cover is used later. Do not return it to the original position.
3Remove Laser Lens Cleaning Tool from Tray 1.
4Close Tray 1.

d-COLOR P3100 1-9
1.2 Cleaning 1
5Open the Front Door.
6Pull out the Waste Toner Bottle as well as the Toner Cartridge and Imaging Unit of the target color.
%For information on how to remove a Toner Cartridge, refer to page 2-4. Inclining the Toner Car-
tridge may cause toner to spill.
%For information on how to remove a Waste Toner Bottle, refer to page 2-15. Inclining the Waste
Toner Bottle may cause toner to spill.
%For information on how to remove an Imaging Unit, refer to page 2-9. Cover the removed Imaging
Unit with a cloth to keep from being affected by light.
7Install the cover on the removed Imaging Unit.

1-10 d-COLOR P3100
Cleaning
11.2
8Insert the Laser Lens Cleaning Tool into the cleaning hole located at the bottom of the Imaging Unit
with the sponge side facing downward, then move it back and forth several times.
9Install all of Toner Cartridge, Waste Toner Bottle, and Imaging Unit.
%CAUTION
Do not touch the copper terminals of the Toner Cartridge and Imaging Unit. Doing so may cause
static electricity to damage the product.
%For information on how to install a Toner Cartridge, refer to page 2-4.
%For information on how to install a Waste Toner Bottle, refer to page 2-15.
%For information on how to install an Imaging Unit, refer to page 2-9.

d-COLOR P3100 1-11
1.2 Cleaning 1
10 Close the Front Door.
11 Pull out Tray 1.
12 Return the Laser Lens Cleaning Tool to the holder in Tray 1.
13 Close the cover.
14 Close Tray 1.
15 In the same way, clean the laser lens at the position corresponding to each Imaging Unit.
%The Laser Lens Cleaning Tool is an accessory of this machine. Return the Laser Lens Cleaner to
the laser lens cleaner holder so that you do not lose it.

1-12 d-COLOR P3100
Cleaning
11.2

2Checking and Replacing
Consumables

d-COLOR P3100 2-3
2.1 Checking the status of consumables 2
2 Checking and Replacing Consumables
2.1 Checking the status of consumables
Consumables replacement messages
Users will be informed of the time to replace consumables via a message displayed on the screen.
dReference
If a warning such as for toner replacement or a paper jam occurs on this machine, it can be sent to a registered
E-mail address. For information on the setting procedure, refer to [User's Guide Applied Functions].
Message Description Reference
[TONER LOW] The toner is about to run out.
Prepare the specified Toner Cartridge.
-
[TONER OUT] Toner is depleted. Replace the Toner Cartridge.page2-4
[I-UNIT LOW] The operating life of the Imaging Unit will expire soon.
Prepare the specified Imaging Unit.
-
[I-UNIT LIFE] The operating life of the Imaging Unit has expired.
Replace the Imaging Unit.
page 2-9
[TRANS. BELT END OF LIFE] The operating life of the Transfer Belt Unit has ex-
pired. Printing is possible, but the printing quality is not
assured.
Replace the Transfer Belt Unit.
page 2-19
[FUSER UNIT END OF LIFE] The operating life of the Fuser Unit has expired. Print-
ing is possible, but the printing quality is not assured.
Replace the Fuser Unit.
page 2-23
[WASTE TONER NEAR
FULL]
The Waste Toner Bottle will become full soon.
Prepare a new Waste Toner Bottle.
-
[WASTE TONER FULL] The Waste Toner Bottle will become full soon.
Replace the Waste Toner Bottle.
page 2-15
[TRANS. ROLLER END OF
LIFE]
The operating life of the Transfer Roller has expired.
Printing is possible, but the printing quality is not as-
sured.
Replace the Transfer Roller.
page 2-17

2-4 d-COLOR P3100
Replacing consumables
22.2
2.2 Replacing consumables
NOTICE
A failure, which was caused because you did not follow the procedures described in this user's guide, is not
included in the warranty.
2.2.1 Replacing a Toner Cartridge
Handling a Toner Cartridge
When handling a Toner Cartridge, be careful of the following.
-This machine supports four Toner Cartridge: black, yellow, magenta, and cyan. When handling a Ton-
er Cartridge, take care not to spill toner on this machine or your hand.
-Replace a Toner Cartridge with an unused product. If a Toner Cartridge is replaced with a used one,
the Message Window may not be cleared, or the toner level may not be displayed correctly.
-Do not forcibly open the Toner Cartridge. If toner has leaked, avoid toner inhaling or skin contact as
much as possible.
-If your clothes or hand has been stained with toner, wash it off with soap and water.
-If you have inhaled toner, move to a fresh air place, then gargle well with a large amount of water. If you
have had a symptom such as a cough, see your doctor.
-If any toner enters your eyes, immediately wash them with running water for 15 minutes or more. If pain
persists, see your doctor.
-If you have drunk toner, wash your mouth out well, then drink one or two glasses of water. See your
doctor, if necessary.
-Keep Toner Cartridge out of reach of babies and children.
-When handling a Toner Cartridge, do not touch the printed circuit board installed on the Toner Car-
tridge.
-When replacing a Toner Cartridge, do not touch the spring contact of the main unit.
-Do not store any toner container (Toner Cartridge, Photoreceptor Unit, Imaging Unit, or Development
Unit) near a product that is affected by magnetism such as precision measuring equipment or storage
media. It may damage functions of such products.
Storing Toner Cartridges
Store Toner Cartridge as shown below.
-Do not open the protection bag before installing a Toner Cartridge.
-Store Toner Cartridges in a cold dark place, away from direct sunlight.
-Store Toner Cartridges in a place in which the temperature is 95°F (35°C) or less and the humidity is
85% or less with no dew condensation. If a Toner Cartridge is moved from a cold place to a warm
place with high humidity, a dew may form. which may affect printing quality. Before using a Toner Car-
tridge, leave it for approximately one hour to adjust to the ambient environment.
-Keep Toner Cartridges horizontal. Do not place a Toner Cartridge in the reverse direction from that
specified. Doing so may cause toner in a Toner Cartridge to become hard or uneven.
-Do not touch salty air or corrosive gases such as aerosol.
Tips
Guidance for recovering used Toner Cartridge
-Put the used Toner Cartridge in a bag, place the bag in the box in which the Toner Cartridge was in-
cluded at the time of purchase, then send the box to us. Securely seal the bag and box with tape, being
careful of the toner in the Toner Cartridge. The recovered Toner Cartridge and Imaging Unit are re-
cycled.