Olivetti JS-602 User manual

JS-602
Option Printer
SERVICE MANUAL
Code Y111430-0

PUBLICATION ISSUED BY:
Olivetti S.p.A.
77, Via Jervis - 10015 Ivrea (TO)
Italy
Copyright © 2009, Olivetti
All rights reserved

JS-602OUTLINEMAINTENANCE
Field Service Ver. 1.0 Jul. 2009
i
CONTENTS
JS-602
OUTLINE
1. PRODUCT SPECIFICATIONS ................................................................................ 1
MAINTENANCE
2. PERIODICAL MAINTENANCE PROCEDURE ....................................................... 3
2.1 Paper exit section ................................................................................................. 3
2.1.1 Cleaning of the transport rollers/exit rollers .................................................. 3
3. OTHER MAINTENANCE ITEM ............................................................................... 4
3.1 Items not allowed to be disassembled and adjusted ............................................ 4
3.2 Disassembly/reassembly parts list........................................................................ 5
3.3 Disassembly/reassembly procedure..................................................................... 5
3.3.1 Separator ...................................................................................................... 5
3.3.2 Front cover .................................................................................................... 6
3.3.3 Rear cover..................................................................................................... 6
3.3.4 3rd entrance switching solenoid (SD404) ..................................................... 7

JS-602
OUTLINEMAINTENANCE
Field Service Ver. 1.0 Jul. 2009
ii
Blank Page

Field Service Ver. 1.0 Jul. 2009 1. PRODUCT SPECIFICATIONS
1
JS-602OUTLINE
OUTLINE
1. PRODUCT SPECIFICATIONS
A. Type
B. Functions
C. Paper type
D. Machine specifications
E. Operating environment
Conforms to the operating environment of the main body.
NOTE
• These specifications are subject to change without notice.
Name Job separator
Type Add-on finishing device externally mounted on top of finisher
Installation Fixed to finisher
Document alignment Center
Modes Group, Sort (during copy, print, or fax mode)
Type Size Weight Tray capacity
Plain paper
A5S to A3
5-1/2 × 8-1/2S to
11 × 17
64 to 90 g/m2
17 to 24 lb
100 sheets:
A4, 8-1/2 × 11 (80 g/m2, 21.25 lb)
50 sheets:
except A4, 8-1/2 × 11 (80 g/m2, 21.25 lb)
(Height: up to 28 mm, 1.1 inch)
Power requirements DC 5 V, DC 24 V (supplied from finisher)
Dimensions 341 mm (W) × 537 mm (D) × 149 mm (H)
13.43 inch (W) × 21.14 inch (D) × 5.87 inch (H)
Weight 1.75 kg (3.86 lb)
Y111430-0Service Manual

1. PRODUCT SPECIFICATIONS Field Service Ver. 1.0 Jul. 2009
2
JS-602
OUTLINE
Blank Page
Service Manual Y111430-0

Field Service Ver. 1.0 Jul. 2009 2. PERIODICAL MAINTENANCE PROCEDURE
3
JS-602MAINTENANCE
MAINTENANCE
2. PERIODICAL MAINTENANCE PROCEDURE
2.1 Paper exit section
NOTE
• The alcohol described in the cleaning procedure of maintenance represents theޓ
isopropyl alcohol.
2.1.1 Cleaning of the transport rollers/exit rollers
A. Periodically cleaning parts/cycle
• Transport roller: Every 100,000 counts
• Exit roller: Every 100,000 counts
B. Procedure
1. Open the cover.
2. Using a cleaning pad with alcohol,
wipe the transport rollers [1] clean of
dirt.
3. Using a cleaning pad with alcohol,
wipe the exit rollers [1] clean of dirt.
A10CF2C001DA
[1]
A10CF2C002DA
[1]
Y111430-0Service Manual

3. OTHER MAINTENANCE ITEM Field Service Ver. 1.0 Jul. 2009
4
JS-602
MAINTENANCE
3. OTHER MAINTENANCE ITEM
3.1 Items not allowed to be disassembled and adjusted
A. Paint-locked screws
NOTE
• To prevent loose screws, a screw lock in blue or green series color is applied to
the screws.
• The screw lock is applied to the screws that may get loose due to the vibrations
and loads created by the use of machine or due to the vibrations created during
transportation.
• If the screw lock coated screws are loosened or removed, be sure to apply a screw
lock after the screws are tightened.
B. Red-painted screws
NOTE
• The screws which are difficult to be adjusted in the field are painted in red in order
to prevent them from being removed by mistake.
• Do not remove or loosen any of the red-painted screws in the field. It should also
be noted that, when two or more screws are used for a single part, only one repre-
sentative screw may be marked with the red paint.
C. Variable resistors on board
NOTE
• Do not turn the variable resistors on boards for which no adjusting instructions
are given in Adjustment/Setting.
D. Removal of PWBs
CAUTION
• When removing a circuit board or other electrical component, refer to “Handling of
PWBs” and follow the corresponding removal procedures.
• The removal procedures given in the following omit the removal of connectors and
screws securing the circuit board support or circuit board.
• Where it is absolutely necessary to touch the ICs and other electrical components
on the board, be sure to ground your body.
Service Manual Y111430-0

Field Service Ver. 1.0 Jul. 2009 3. OTHER MAINTENANCE ITEM
5
JS-602MAINTENANCE
3.2 Disassembly/reassembly parts list
3.3 Disassembly/reassembly procedure
3.3.1 Separator
1. Remove the front cover.
See P.6
2. Remove the rear cover.
See P.6
3. Remove two screws [1] and connec-
tor [2], and remove the separator [3].
Section Part name Ref. page
Unit Separator P. 5
Exterior parts Front cover P. 6
Rear cover P. 6
Other 3rd entrance switching solenoid (SD404) P. 7
A10CF2C500DA
[2]
[1]
Y111430-0Service Manual

3. OTHER MAINTENANCE ITEM Field Service Ver. 1.0 Jul. 2009
6
JS-602
MAINTENANCE
3.3.2 Front cover
1. Unlock three tabs [1], and remove
the front cover [2].
2. Reinstall the above parts following the removal steps in reverse.
3.3.3 Rear cover
1. Unlock the tab [1], and remove the
spacer [2].
2. Unlock three tabs [1], and remove
the rear cover [2].
3. Reinstall the above parts following the removal steps in reverse.
A10CF2C501DA
[1]
[1]
A10CF2C502DA
[1]
A10CF2C503DA
[1]
Service Manual Y111430-0