olympia electronics BSR-6157 User manual

BSR-6157
Page 1 from 4 921615700_09_003
GENERAL
The user have to read carefully the following instructions, in order to be properly informed and keep them
for future use.
The BSR-6157 is an analogue addressable smoke detector which integrates functions of optical smoke
and heat detection and it can work with any fire panel supports Olympia A Protocol. It can be adjusted to
detect multiple levels of smoke and heat offering flexibility and rich functionality. Also, it integrates a short
circuit isolation circuit which is automatically activated and disconnects the defective node from the
remaining loop, allowing it to be located by the panel.
The detector sends to the main panel an analogue value which depends on the concentration of smoke
and heat. The value is 100 in concentration of 0.107dB/m (small amount of smoke) or a temperature of
o o
57 C and increases proportionally to 120 in concentration of 0.300dB/m or a temperature of 90 C. When a
sudden increase in temperature is detected the detector sends the value of 121.
By default the panel is set to sound an alarm when the concentration of smoke is 0.107dB/m or the
temperature is 57 C. The user can change this setting from the panel for each detector and define any
level of smoke concentration or temperature between the lower and the upper limits, specifying the
sensitivity of the system depending on the requirements of each site. Also, the user can select A1R or A2S
working mode through the panel.
They are composed by two parts. A plastic base which is placed on the ceiling and the main body of the
o
detector which fits on the plastic base with a simple rotation to the right. The detectors have a 360 visible
led and a remote led driver which are light up constantly in case of detection of fire, till cancelled from the
panel. Also, they are staying lit even if the sirens are silenced from the panel, so the detector which
o
140μΑ
11-30V DC
TEMPERATURE SENSITIVITY
SMOKE CONCENTRATION SENSITIVITY
1A
5A
IP42
100mΩ
2.5mA (with activated LED)
Adjustable from 0.107 to 0.300 in 0.010 dB/m steps
Adjustable from 57 to 90 in 1.5 steps oC
10.7 - 12.7
9.3 - 10.6
Up to 95%
ο
-40 to 70 C
ABS/PC
160 gr.
103 (d) x 55 (h) mm
2 years
Remote LED driver
Alarm LED
INDICATORS
OUTPUT
Analogue addressable optical smoke and
rate-of-rise heat detector with integrated isolator
TECHNICAL CHARACTERISTICS
MAIN VOLTAGE
STANDBY CONSUMPTION
ALARM CONSUMPTION
MAXIMUM LOOP CURRENT (Ic max, -L in/out)
MAXIMUM SWITCH CURRENT (Is max, -L in/out)
MAXIMUM SERIES RESISTANCE (Zc max, -L in-out)
MAXIMUM LEAKAGE CURRENT
IN ISOLATION MODE (I max, -L in/out)L
ISOLATION VOLTAGE (Vso min-max)
RECONNECT VOLTAGE (Vsc min-max)
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
OPERATING TEMPERATURE RANGE
RELATIVE HUMIDITY
CONSTRUCTION MATERIALS
EXTERNAL DIMENSIONS
TYPICAL WEIGHT
GUARANTEE
25mA pulses (6ms duration every 2sec)
Thank you for your trust in our products
Olympia Electronics - European manufacturer
EN 54-5 EN 54-7 EN 54-17, ,
CLASS A1R/A2S
Olympia A ProtocolCOMMUNICATION PROTOCOL

detected the alarm is visible. They are turned off only when a reset command is given from the panel. The
indicator led blinks every 10 sec indicating the connection status with the main panel.
SETTING THE ADDRESS
Each detector must have a unique address, with which it is recognised from the panel. It is forbidden for
two devices in the same loop to have the same address. To set it up you can use the function of changing
address point as described in the user manual of the panel.
.
-
- Dust compensation and automatic generation of cleaning notifications. Stable level of
detection regardless of detector’s working hours.
- Compensation of smoke measurements based on ambient temperature which ensures high
precision measurements even under extreme environmental conditions.
- Automatic fault diagnosis.
- Adjustable smoke and temperature alarm level for maximum flexibility.
- 360
UID:
In every device there is a double sticker with the UID (Unique Identifier) number. This number is
unique for each device.
INSTALLATION
The detectors should be placed in the ceiling in visible points without side obstacles, away from places
that are barely ventilated or with strong air currents and water vapor. Each detector covers an area of 50
2
m while the distance between two detectors should not be more than 15m. Also, they must be placed at
least 50 cm away from fluorescent lamps. Cable diameter should be from . to .
MAINTENANCE & FUNCTIONAL TESTING
The detector has fault diagnosis and dust compensation functions, which automatically informs you when
replacement or cleaning actions are required. These functions combined with periodic manual testing
ensure maximum security level. The manual testing procedure is carried out by spraying a small amount
of smoke into the detector with an A-752 spray or a counterpart product. It is suggested to carry out a test
every 6 months or after a change in the position of the sensor. A key element of its proper function is the air
to be able to freely circulate inside it. So be careful not to block the openings of the outer cover. Before the
manual testing it is suggested to enable the special “walk in test” mode from the panel.
CAUTION !!
After installation the device must not be covered with dust or be painted or anything else happen that will
block the smoke to get to the sensor. Special attention must be given during the installation and the use of
the device, since the user assumes full responsibility for proper operation afterwards.
Also, during site works place the plastic cover to the detector as shown in the picture below to protect the
device from dust.
0 5 2 5mm
Additional features of the device :
ooptically visible LED.
Integration of dynamic algorithms for noise and false alarm rejection.
Page 2 from 4 921615700_09_003

1. Remove the detector from its base rotating to the left till the side marks are aligned.
2. Fasten the base with the supplied mounting materials (point 5).
3. Connect the power cables (minding the correct polarity) according to the requirements of the
installation (Figure 1, 2).
4. Place the detector carefully so that the side marks are on the same position and rotate the detector
clockwise until it locks. Power the device and after 3-5 seconds it is ready for operation.
CONNECTION
1. + IN/OUT: Connect to (+L) of the loop.
2. - IN: Connect to (-L) of the loop.
3. - OUT: Connect to (-L) of the loop.
4. - R : External LED connection.
5. : Connected to the cable’s shield (when shield is used).
Mounting base
Figure 1
55
R
+
-R
Installation process
2
Connection
with exterrnal
LED
U
T
/O
N
I
+
N
- I
T
U
- O
Side mar ks
Page 3 from 4
e
n
i
t
n
s
g
a
f
d
t
e
n
t
a e
c
m
h
1
Indica ting
LED
Figu re 2
Loop
Loop
-R
U
T
/O
N
I
+
N
- I
T
U
- O
Loop Loop
-R
-R -R
-R
-R
+L -L +L -L
CN2
U
T
/O
N
I
+
N
- I
T
U
- O
U
T
/O
N
I
+
N
- I
T
U
- O
U
T
/O
N
I
+
N
- I
T
U
- O
U
T
/O
N
I
+
N
- I
T
U
- O
U
T
/O
N
I
+
N
- I
T
U
- O
PE
IN OUT
921615700_09_003

Page 4 from 4
WARRANTY
WARRANTY
Olympia Electronics guarantees the quality, condition and operation of the goods. The period of warranty
is specified in the official catalogue of Olympia Electronics and also in the technical leaflet, which
accompanies each product. This warranty ceases to exist if the buyer does not follow the technical
instructions included in official documents given by Olympia Electronics or if the buyer modifies the goods
provided or has any repairs or re-setting done by a third party, unless Olympia Electronics has fully
agreed to them in writing. Products that have been damaged can be returned to the premises of our
company for repair or replacement, as long as the warranty period is valid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge the
buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or not the
buyer the transportation cost.
HEAD OFFICE
72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Εginio Pierias Greece
www.olympia-electronics.gr
[email protected]
921615700_09_003