Omnilux MINI User manual

User Guide
Skin Corrector

2 3
OMNILUX™ MINI SKIN CORRECTOR

2 3
USER GUIDE
It is mandatory that users of this device read and
comprehend all information in this User Guide prior
to use of the Omnilux™ Mini Skin Corrector device.
You must follow all the instructions in the User Guide.
Please contact us if you have any comments about the Skin
Corrector device or this User Guide or if you experience any side
effects that are not mentioned in this User Guide or are more
severe than those described in the User Guide.
www.omniluxled.com
GlobalMed Technologies Co. KD&A PTY LTD
163 Camino Dorado Suite B 288 Flinders Street
Napa, CA 94558 Adelaide SA 5000
Tel: +1-707-224-0200 RP: Certainty IP Ltd
www.omniluxled.com Dublin, D18 CV48
+353 1582 9003
The information in this document is proprietary to
iSMART Developments Ltd, and supplied on the
understanding that it shall be kept condential to
recipients and that it shall not be reproduced and/or
used for commercial purposes without the written
consent of iSMART Developments Ltd.

4 5
OMNILUX™ MINI SKIN CORRECTOR
Contents
Who should use the Skin Corrector device ................... 5
Device Description ................................................5
Intended Use.......................................................7
Contraindications, Warnings and Precautions .................7
Contraindications .................................................7
Warnings..........................................................9
General Safety ...................................................11
Precautions.......................................................11
Risks and Benets ................................................12
Potential Risks....................................................12
Potential Benets ................................................12
First Time Setup ..................................................13
Unpacking and charging the Skin Corrector device ...............13
Charging the Skin Corrector device...............................13
Charging Status of the Skin Corrector device ................14
Sensitization test..................................................14
Using the Skin Corrector device................................16
Treatment Recommendations.....................................16
Carrying out a treatment .........................................16
How to use the Hydrocolloid Patches .........................18
Care and Maintenance...........................................21
Cleaning the Skin Corrector device............................20
Disposal/Recycling ...............................................22
Troubleshooting ..................................................22
Labeling............................................................24
Technical specication ...........................................24
Explanation of symbols ..........................................25
Warranty ...........................................................27
Standard Warranty ...............................................27
Warranty exceptions..............................................27
What to do if your product is faulty ...............................27

4 5
USER GUIDE
Before using the Skin Corrector device you must
carry out a sensitization test and wait 6 hours.
Who should use Skin Corrector device
Thank you for choosing the
Skin Corrector device
.
The
Skin Corrector device
is suitable for adults wishing to treat
pigmentation problems such as age spots, pigmentation,
and blemishes.
If you have purchased the
Skin Corrector device
and nd that
it is NOT suitable for you, please contact your supplier to
return the device within 30 days with proof of purchase
.
Device Description
The Skin Corrector device is a battery operated, cordless
wearable Light emitting diode (LED) device intended to
emit light in the red (630nm) and near infrared (830nm)
region of the light spectrum for the treatment of treat
pigmentation problems such as age spots, pigmentation,
and blemishes.
The Skin Corrector device system consists of the following
key components.
1. 1 x Silicone LED Patch
2. 1 x Magnetic 2 pin, 4mm to USB A Charging Cable
3. 14 x Individually Wrapped Hydrocolloid Patches
including 1 Sensitization Test Patch
4. 1 x User Guide
The Skin Corrector device is a silicone exible patch
containing LEDs. The LEDs generate the light.
The LEDs produce Red: (630nm +/- 10nm) and Near
Infra-Red (830nm +/-10nm) light in the visible spectrum.
The device works through non-thermal mechanisms called
Photobiomodulation.

6 7
OMNILUX™ MINI SKIN CORRECTOR
The LEDs are driven by an integrated 3.7V, 37mAh Lithium
Polymer battery.
The battery is charged via a magnetic 2 pin, 4mm to USB A
connector that plugs into a standard 5v USB A power
adaptor. The device cannot be operated while in charging
mode.
The charging status of the device is indicated by a single
indicator LED on the rear of the Skin Corrector device and
the treatment LEDs.
In charging mode.
i. Solid green – battery is fully charged.
ii. Solid orange – battery charging.
The Skin Corrector device contains a simple ON/
OFF button ( ) that switches the LEDs ON/OFF. The
treatment time is 10 minutes. The device automatically
turns OFF after the 10-minute treatment cycle. The user
may stop the treatment program during the 10 minutes
by pressing the ON/OFF button.
The LED device is worn on the face and held in place by
an adhesive hydrocolloid patch. The adhesive hydrocolloid
patch is impregnated on both sides with an elastomer and
hydrogenated petroleum resin that acts as an adhesive.
The hydrocolloid patch contains CMC Carboxymethyl
cellulose (Cellulose Gum), Styrene/Isoprene Copolymer,
Homopolymer, Hydrogenated Rosin, Parafnum Liquidum
(Mineral oil), PET, Azelaic Acid, Ascorbic Acid (Vitamin C),
Sodium Hydroxide, Sodium Hyaluronate and
Pentaerythritol tetrakis.
You are supplied with a set of 14 adhesive hydrocolloid
patches for treatment, one of which must be used to
carry out a Photosensitivity patch test before starting your

6 7
USER GUIDE
The LEDs are driven by an integrated 3.7V, 37mAh Lithium
Polymer battery.
The battery is charged via a magnetic 2 pin, 4mm to USB A
connector that plugs into a standard 5v USB A power
adaptor. The device cannot be operated while in charging
mode.
The charging status of the device is indicated by a single
indicator LED on the rear of the Skin Corrector device and
the treatment LEDs.
In charging mode.
i. Solid green – battery is fully charged.
ii. Solid orange – battery charging.
The Skin Corrector device contains a simple ON/
OFF button ( ) that switches the LEDs ON/OFF. The
treatment time is 10 minutes. The device automatically
turns OFF after the 10-minute treatment cycle. The user
may stop the treatment program during the 10 minutes
by pressing the ON/OFF button.
The LED device is worn on the face and held in place by
an adhesive hydrocolloid patch. The adhesive hydrocolloid
patch is impregnated on both sides with an elastomer and
hydrogenated petroleum resin that acts as an adhesive.
The hydrocolloid patch contains CMC Carboxymethyl
cellulose (Cellulose Gum), Styrene/Isoprene Copolymer,
Homopolymer, Hydrogenated Rosin, Parafnum Liquidum
(Mineral oil), PET, Azelaic Acid, Ascorbic Acid (Vitamin C),
Sodium Hydroxide, Sodium Hyaluronate and
Pentaerythritol tetrakis.
You are supplied with a set of 14 adhesive hydrocolloid
patches for treatment, one of which must be used to
carry out a Photosensitivity patch test before starting your
treatment course.
The equipment is not used to make measurements
of any sort, or to draw any conclusions regarding the
indication to treat. The equipment does not require
checks on the light output as the LEDs do not dim with
age to any practical extent.
Intended Use
The
Skin Corrector device
is an over-the-counter device
intended to emit energy in the red and Near Infra-red
spectrum and is intended to help in the treatment of
pigmentation problems such as age spots, pigmentation
and blemishes.
The Skin Corrector device
is intended to be used in the
home by adults.
Contraindications, Warnings and Precautions
Contraindications
• DO NOT share the Skin Corrector device with any other
person. The Skin Corrector device is for single person
use only.
• DO NOT
reuse the hydrocolloid patches between
treatment
sessions. The hydrocolloid patches are for single
use only.
• DO NOT use the Skin Corrector device to treat any other
conditions apart from those listed in the intended use. The
Skin Corrector device has not been tested for any other
conditions than those listed, and the risk is unknown.
• DO NOT use the Skin Corrector device if you are
pregnant, planning on becoming pregnant or
breastfeeding. The Skin Corrector device has NOT
been tested on pregnant or breast-feeding women and
therefore the risk to the foetus, neonate or pregnant

8 9
OMNILUX™ MINI SKIN CORRECTOR
women is unknown.
• DO NOT use the Skin Corrector device if you have an
allergy to Silicone or Polyethylene terephthalate. The
treatment surfaces of the Skin Corrector device contain
medical grade silicone and Polyethylene terephthalate.
• DO NOT use the Skin Corrector device if you have an
allergy to Hydrocolloid bandages. The LED device xes to
your face using an adhesive hydrocolloid patch.
• DO NOT use the Skin Corrector device if you suffer from
any genetic conditions of the eyes. If you are unsure about
any related eye condition and using the Skin Corrector
device contact a health care professional.
• DO NOT use the Skin Corrector device if you suffer from
lupus erythematosus, photosensitive eczema, or albinism.
If you use the Skin Corrector device to treat lupus
erythematosus, photosensitive eczema or albinism you
may cause a severe skin reaction.
• DO NOT use the Skin Corrector device if you suffer
from any photosensitive disorder (sensitization to light).
If you use the Skin Corrector device and you suffer from
a photosensitive disorder; you may cause a severe skin
reaction.
• DO NOT use the Skin Corrector device if you suffer from
light induced headaches.
• DO NOT use the Skin Corrector device if you are taking
any medication that can cause photosensitivity. If you
use the Skin Corrector device and you are taking any
medication that can cause photosensitivity you may cause
a severe skin reaction.
• For a full list of drugs that can cause photosensitivity,

8 9
USER GUIDE
please visit: www.omniluxled.com
Photosensitivity is a common side effect of various
medications. These can include certain antibiotics,
chemotherapy drugs, and diuretics. If you are unsure
about any medication, you may be taking consult your
healthcare provider.
Other substances not listed above can also
cause photosensitivity.
• Common examples of these substances are:
St John’s Wort, coal tar, deodorants, antibacterial soaps,
articial sweeteners, naphthalene (mothballs), petroleum
products, brightening agents found in laundry detergent,
and cadmium sulphide (a chemical injected into the skin
during tattooing).
Warnings
• Before using the Skin Corrector device you must carry out
a sensitization test. Please read the section
“Sensitization test” on how to carry out the test.
• DO NOT over ex the Skin Corrector device.
Although it is exible, it is not designed to withstand
excess bending or folding.
• Keep the Skin Corrector device away from Sharp Objects.
• DO NOT use the Skin Corrector device in any way that is
not exactly as specied in this User Guide. Use of the Skin
Corrector device other than exactly as specied in this
User Guide has not been tested and the risk is unknown.
• DO NOT use the Skin Corrector device in an environment
that is NOT specied by the manufacturer, as this may

10 11
OMNILUX™ MINI SKIN CORRECTOR
cause damage to the device or harm to the user.
• TURN OFF and REMOVE the Skin Corrector device
immediately if it feels hot or your skin feels uncomfortably
warm. DO NOT continue treatments and contact
customer services.
• STOP using the Skin Corrector device during a treatment
if you experience headaches or changes in vision. DO
NOT continue treatments and contact customer services.
• DO NOT use the Skin Corrector device without rst
removing creams, lotions, or make-up BEFORE treatment.
Some ingredients in these products may cause light
sensitization or may reduce the effect of the treatment. If
you use the Skin Corrector device without removing these
products, you may cause a skin reaction, or may reduce
the effect of the treatment.
• Only use the adhesive hydrocolloid patches
recommended. Other adhesive patches are available but
have not been tested with the device and may block light
penetration and reduce the effects of the treatment.
• DO NOT use the hydrocolloid after its expiry date.
• NEVER use the Skin Corrector device near water or where
water can be spilt onto the equipment. DO NOT use the
Skin Corrector device if you think it has come into contact
with water.
• Keep the Skin Corrector device away from HOT surfaces or
direct sunlight.
• DO NOT attempt to modify the Skin Corrector device in
any way. Modifying the Skin Corrector device will void your
warranty. Modifying the Skin Corrector device could cause
an electric shock when the system is used again. The
system contains no serviceable parts.

10 11
USER GUIDE
• DO NOT use the Skin Corrector device if the device,
packaging, or cable are damaged in any way.
• DO NOT use the Skin Corrector device any longer if it
shows any signs of damage to the material through wear
and tear.
• DO NOT leave the Skin Corrector device unattended
when it is switched on. Accidental mishandling of the
device could lead to the risk of re or burns.
General Safety
The Skin Corrector is an electrical device, which under
certain circumstances could present an electrical shock
hazard to the user. Please read this User Guide thoroughly
and follow directions stated in the manual to assure
maximum safety during operation.
The Skin Corrector device may only be charged with the
charging cable that is supplied with the device. Use of other
charging cables may not be safe and could lead to electric
shock.
Precautions
• DO NOT stare directly at the LED light source.
• DO NOT use the Skin Corrector device without a
hydrocolloid.
• The Skin Corrector device cannot be used in
charging mode.
• Unplug The 2-pin charging cable from the USB charging
port when not in use.
• Before each use, with the device switched off, clean the
Skin Corrector device. All surfaces of the Skin Corrector
device may be cleaned by following the cleaning

12 13
OMNILUX™ MINI SKIN CORRECTOR
instructions.
• DO NOT use any other cleansing products other than
those stated in the cleaning instructions. Use of other
cleansing products may damage the Skin Corrector
device.
• Store the Skin Corrector device at room temperature in
dry conditions, away from direct sunlight.
• Don’t use the Skin Corrector device in Direct Sunlight.
• Take care when using the Skin Corrector device
around young children. Electrical cables can present a
strangulation hazard.
• Take care when removing the patch and hydrocolloid, as
there is a risk of damaging the top layer of the skin if it is
removed too vigorously.
• DO NOT charge the Skin Corrector device if the USB
socket or wall adapter you are using has poor connections
or becomes hot. Make sure you plug the device into a
high quality, CE certied USB charging socket or adapter
to avoid the risk of re and burns.
• DO NOT subject the Skin Corrector device to heavy
shocks to avoid risk of damage to the device, if you
damage the device, do not use it any longer.
Risks and Benets
Potential Risks
This list, although not exhaustive, lists what are considered
to be among the mostly likely adverse effects that could
occur with use of the device.
Immediately after treatment skin may appear red. Skin

12 13
USER GUIDE
should return to normal within 1-2 hours.
Some users have reported skin aking or peeling, associated
pruritis and dryness. This is transient and fades within a
few days.
Temporary headaches may occur immediately following the
light treatment.
Although this device emits levels of visible and infrared
light that are considered to be safe for the skin, if you have
adverse reactions after using the device that do not resolve,
you should stop using the device immediately.
If you experience a side effect that is not described above
or is of greater severity than described above, please STOP
using the device immediately and contact a Healthcare
Professional and iSMART Developments Ltd or your provider
and your representative Competent Authority if you deem
it applicable.
Potential Benets
People who have undergone a course of 3-5 weekly
treatments for 6 weeks using the Skin Corrector device
report a reduction in age spots, pigmentation and
blemishes.
First Time Setup
Unpacking and charging the Skin Corrector
device
Unpack the Skin Corrector device and check off the parts
described in Device description.
Visually inspect the parts and connections. Return the device
to your supplier if you think the device or connecting parts

14 15
OMNILUX™ MINI SKIN CORRECTOR
or components are damaged or have been previously used.
DO NOT use the Skin Corrector device if you notice device
or connecting parts or components are damaged.
Charging the Skin Corrector device
Before use, fully charge the device.
The Skin Corrector device uses an integrated lithium-ion
polymer battery. When the LED device is connected to
the power supply do not attempt to use the device as
the LEDs will not illuminate.
1. To charge the Skin Corrector device battery connect
the 2-pin connection cable to the port on the upper
side of the LED patch.
2. Insert the USB A connector into a suitable USB power
supply or laptop port.
3. The indicator LED will illuminate Orange to show that
the patch is charging. The patch is fully charged when
the indicator LED is solid green.
4. When fully charged the battery will deliver 3-4
treatments before recharging. The lifetime of the
Lithium battery can be maximized by allowing it to fully
charge and then fully discharge during regular use.
5. Always ensure the LED device is fully charged before
commencing a treatment session.
6. Unplug the 2-pin charging cable from the USB A
charging port when not in use.

14 15
USER GUIDE
Charging Status of the Skin Corrector device
The Skin Corrector device uses a single display LED on the
rear of the LED device and treatment LEDs to indicate the
status of the battery.
Solid Green – Battery is fully charged.
Solid Orange – Battery is charging (Charging Mode).
Low Battery Mode – Identied by Treatment LEDs
Flashing – There is not enough battery charge to complete a
treatment cycle please recharge your device.
Sensitization test
Before carrying out your rst treatment you must
carry out a sensitization test to see if you are
sensitive to light or the adhesive hydrocolloid patch.
Follow the step-by-step guide below.
DO NOT attach the Skin Corrector device to your
face, the sensitization test should be carried out on
your arm.
1. Ensure the Skin Corrector device is fully charged.
2. Remove one of the adhesive hydrocolloid patches from
its packaging.
3. See the “How to use the Hydrocolloids” section for a
step-to-step guide to using the hydrocolloids.

16 17
OMNILUX™ MINI SKIN CORRECTOR
4. Unpeel the device side of the backing paper off the
adhesive hydrocolloid patch.
5. Place the sticky side of the adhesive hydrocolloid patch
onto the LED side (white) of the Skin Corrector device.
Ensure the adhesive hydrocolloid device aligns with the
shape of the Skin Corrector device.
6. Press down across the entire surface of the adhesive
hydrocolloid patch.
7. Peel the face side of the backing paper from the
adhesive hydrocolloid patch.
8. Attach the Skin Corrector device to the inside of your
left or right forearm and push down gently.
9. Switch ON the Skin Corrector device and allow it to run
for a full treatment (10 minutes)
10. At any time if your skin feels HOT or uncomfortable
STOP using the device immediately.
11. After the treatment, carefully remove the Skin Corrector
device and adhesive hydrocolloid patch from the
treatment area. Discard the test adhesive hydrocolloid
patch in the general waste.
12. Wait at least 6 hours. If your skin on your inner arm is
red or itchy, then the treatment is unsuitable for you.
Return the device to the retailer within (30) days of
purchase.
Using the Skin Corrector device
Regarding electromagnetic compatibility (EMC) and
electromagnetic elds (EMF), in and around the home
environment the Skin Corrector device should be kept
away
from radio frequency (RF) equipment to avoid

16 17
USER GUIDE
interference.
Treatment Recommendations:
For the treatment of problems such as age spots,
pigmentation and blemishes the best results are seen by
treating for 3-5 times a week for 6 weeks.
Maintenance treatment should be carried out as
required, according to lifestyle and skin condition.
Carrying out a treatment
DO NOT use the Skin Corrector device without a
Hydrocolloid.
DO NOT over ex the Skin Corrector device. Although
it is exible, it is not designed to withstand excess
bending or folding.
1. Ensure the Skin Corrector device is fully charged
before commencing a treatment session.
2. Cleanse or exfoliate the skin to remove any traces of
skincare.
3. Use a new hydrocolloid every treatment session.
4. See the “How to use the Hydrocolloids” section
for a step-to-step guide to using the hydrocolloids.
5. Unpeel the device side of the backing paper off an
adhesive hydrocolloid patch.
6. Place the sticky side of the adhesive hydrocolloid
patch onto LED side (white) of the Skin Corrector
device. Ensure the adhesive hydrocolloid patch
aligns with the shape of the Skin Corrector device.
7. Press down across the entire surface of the adhesive
hydrocolloid patch.

18 19
OMNILUX™ MINI SKIN CORRECTOR
8. Peel the face side of the backing paper from the
adhesive strip.
9. Using a mirror position the Skin Corrector device
over the treatment area.
10. Switch ON the Skin Corrector device. The device will
automatically switch OFF after 10 minutes. You may
stop the treatment at any time by pressing the
ON/OFF button.
11. After the treatment, carefully remove the Skin
Corrector device and adhesive hydrocolloid patch
from the treatment area.
12. Remove the adhesive hydrocolloid patch from
the Skin Corrector device and discard in general
household waste. If you would like to keep the
hydrocolloid patch on after the LED treatment cycle
has nished, press the hydrocolloid patch onto the
face using the tab and carefully peel the LED device
from the hydrocolloid patch.
13. Clean the Skin Corrector device by following the
instructions in “Cleaning the Skin Corrector
device”. Ensure that the device is NOT being
charged when cleaning.
14. You may treat more than one treatment area in a
treatment session.
DO NOT repeat a treatment on the same treatment area
in the same treatment session.

18 19
USER GUIDE
1Step
Peel the device side of the
hydrocolloid patch. � 2Step
Attach it to the LED
device. � 3Step
Once secured to the device, peel the
face side of the hydrocolloid patch. �
2Step
Attach it to the
LED device. �
1Step
Peel the device side of the
hydrocolloid patch. �
4
Step
SKIN
LED
Press firmly on the face
in the desired treatment
area. �
4
Step
Press firmly on the face
in the desired treatment
area. �
SKIN
LED
3Step
Once secured to the device, peel the
face side of the hydrocolloid patch. �
How to use the Hydrocolloid Patches
SIDE ONE - TO FACE SIDE ONE - TO DEVICE
SIDE ONE - TO FACE SIDE ONE - TO DEVICE
FACE SIDE DEVICE SIDE
Step-to-step diagram for using
the Hydrocolloids

20 21
OMNILUX™ MINI SKIN CORRECTOR
1Step
Peel the device side of the
hydrocolloid patch. � 2Step
Attach it to the LED
device. � 3Step
Once secured to the device, peel the
face side of the hydrocolloid patch. �
2Step
Attach it to the
LED device. �
1Step
Peel the device side of the
hydrocolloid patch. �
4
Step
SKIN
LED
Press firmly on the face
in the desired treatment
area. �
4
Step
Press firmly on the face
in the desired treatment
area. �
SKIN
LED
3Step
Once secured to the device, peel the
face side of the hydrocolloid patch. �
1Step
Peel the device side of the
hydrocolloid patch. � 2Step
Attach it to the LED
device. � 3Step
Once secured to the device, peel the
face side of the hydrocolloid patch. �
2Step
Attach it to the
LED device. �
1Step
Peel the device side of the
hydrocolloid patch. �
4
Step
SKIN
LED
Press firmly on the face
in the desired treatment
area. �
4
Step
Press firmly on the face
in the desired treatment
area. �
SKIN
LED
3Step
Once secured to the device, peel the
face side of the hydrocolloid patch. �
Other manuals for MINI
2
This manual suits for next models
1
Table of contents
Other Omnilux Personal Care Product manuals

Omnilux
Omnilux MINI User manual

Omnilux
Omnilux MINI User manual

Omnilux
Omnilux Clear-U User manual

Omnilux
Omnilux New-U User manual

Omnilux
Omnilux Men User manual

Omnilux
Omnilux CLEAR User manual

Omnilux
Omnilux CLEAR User manual

Omnilux
Omnilux CONTOUR User manual

Omnilux
Omnilux Contour Neck & Decollete User manual

Omnilux
Omnilux CLEAR TN2112 User manual