Omron NA-series User guide

At the end of this document you will find links to products related to this catalog. You can go directly to our shop by
clicking HERE. HERE

Programmable Terminal
NA-series
Startup Guide
V120-E1-01
NA5-15W101
NA5-12W101
NA5-9W001
NA5-7W001

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in
any form, or by any means, mechanical, electronic, photocopying, recording, or otherwise, without the prior written
permission of OMRON.
No patent liability is assumed with respect to the use of the information contained herein. Moreover, because
OMRON is constantly striving to improve its high-quality products, the information contained in this manual is
subject to change without notice. Every precaution has been taken in the preparation of this manual. Neverthe-
less, OMRON assumes no responsibility for errors or omissions. Neither is any liability assumed for damages
resulting from the use of the information contained in this publication.
OMRON, 2014
Trademarks
• Sysmac and SYSMAC are trademarks or registered trademarks of OMRON Corporation in Japan and other
countries for OMRON factory automation products.
• Windows, Windows XP, Windows Vista, Windows 7, Windows 8, Excel, and Visual Basic are registered
trademarks of Microsoft Corporation in the USA and other countries.
• EtherCAT®is registered trademark and patented technology, licensed by Beckhoff Automation GmbH, Germany.
• ODVA, CIP, CompoNet, DeviceNet, and EtherNet/IP are trademarks of ODVA.
• The SD and SDHC logos are trademarks of SD-3C, LLC.
• Portions of this software are copyright 2014 The FreeType Project (www.freetype.org). All rights reserved.
Other company names and product names in this document are the trademarks or registered trademarks of their
respective companies.

1
Introduction
NA-series Programmable Terminal Startup Guide (V120)
Introduction
Thank you for purchasing an NA-series Programmable Terminal.
This manual contains information that is necessary to use the NA-series Programmable Terminal.
Please read this manual and make sure you understand the functionality and performance of the
NA-series Programmable Terminal before you attempt to use it in a control system.
Keep this manual in a safe place where it will be available for reference during operation.
This manual is intended for the following personnel, who must also have knowledge of electrical sys-
tems (an electrical engineer or the equivalent).
• Personnel in charge of introducing FA systems.
• Personnel in charge of designing FA systems.
• Personnel in charge of installing and maintaining FA systems.
• Personnel in charge of managing FA systems and facilities.
This manual covers the following products.
• NA-series Programmable Terminals
Intended Audience
Applicable Products

Relevant Manuals
2NA-series Programmable Terminal Startup Guide (V120)
Relevant Manuals
The basic information required to use an NA-series PT is provided in the following three manuals.
•NA-series Programmable Terminal Hardware User’s Manual (Cat. No. V117)
•NA-series Programmable Terminal Software User’s Manual (Cat. No. V118)
•NA-series Programmable Terminal Device Connection User’s Manual (Cat. No. V119)
Operations are performed from the Sysmac Studio Automation Software.
Refer to the Sysmac Studio Version 1 Operation Manual (Cat. No. W504) for information on the Sys-
mac Studio.
Other manuals are necessary for specific system configurations and applications.
The following manual is also available to walk you through installations and operations up to starting
actual operation using simple examples.
Refer to it as required.
•NA-series Programmable Terminal Startup Guide Manual (Cat. No. V120)

3
Manual Structure
NA-series Programmable Terminal Startup Guide (V120)
Manual Structure
The following page structure is used in this manual.
Note This illustration is provided only as a sample. It may not literally appear in this manual.
Page Structure and Markings
Level 1 heading
Level 2 heading
Level 3 heading
Level 2 heading
A step in a procedure
Manual name
Special information
Level 3 heading
Page tab
Give the current
headings.
Indicates a procedure.
Icons indicate precautions,
additional information, or
reference information.
Gives the number
of the main section.
3 - 5
3 Installation and Wiring
NA Series Programmable Terminal Hardware User’s Manual (V117)
3-3 Installing NA-series PTs
3
3-3-1 Installation in a Control Panel
3-3 Installing NA-series PTs
The NA-series PT is installed by embedding it in a control panel. Panel Mounting Brackets and a Phillips screwdriver are
required to mount the NA-series PT. The required number of Panel Mounting Brackets are included with the NA-series PT.
Use the following installation procedure.
1Open a hole in which to embed the NA-series PT with the following dimensions and insert the
NA-series PT from the front side of the panel.
Additional Information
You can use an NS-USBEXT-1M USB Relay Cable to extend the USB slave connector on the
back panel of the NA-series PT to the front surface of a control panel. If you use the USB Relay
Cable, open a hole with the following dimensions and install the Cable.
2Attach the panel mounting brackets from the back of the panel as shown in the following figure.
The number of mounting brackets depends on the size of the NA-series PT, as shown in the following
table. Refer to Bracket Mounting Locations for Different NA-series PT Sizes on page 3-8, below.
Catch the brackets in the mounting holes in the NA-series PT, pull forward lightly, and then use
a Phillips screwdriver to tighten the screws and secure the NA-series PT to the panel, which will
be held between the mounting brackets and the NA-series PT.
3-3-1 Installation in a Control Panel
Installation in a Control Panel
Model Dimensions
NA5-15W 392 +1/-0 × 268 +1/-0 mm (horizontal × vertical)
NA5-12W 310 +1/-0 × 221 +1/-0 mm (horizontal × vertical)
NA5-9W 261 +1/-0 × 166 +1/-0 mm (horizontal × vertical)
NA5-7W 197 + 0.5/-0 × 141 +0.5/-0 mm (horizontal × vertical)
Model Number of Panel Mounting Brackets
NA5-15W 8 locations
NA5-12W 6 locations
NA5-9W 4 locations
NA5-7W 4 locations
Panel Mounting Bracket Phillips screwdriver
Vertical
Horizontal
Recommended panel thickness: 1.6 to 6.0 mm

Manual Structure
4NA-series Programmable Terminal Startup Guide (V120)
Special information in this manual is classified as follows:
Precautions for Safe Use
Precautions on what to do and what not to do to ensure safe usage of the product.
Precautions for Correct Use
Indicates precautions on what to do and what not to do to ensure proper operation and perfor-
mance.
Additional Information
Additional information to read as required.
This information is provided to increase understanding or make operation easier.
Version Information
Information on differences in specifications and functionality with different versions is given.
Special Information

5
Sections in this Manual
NA-series Programmable Terminal Startup Guide (V120)
1
2
3
4
5
4
3
2
1
Useful Functions
IIndex
Creating HMI Application and Debugging
Preparing in advance
HMI Application Basics
System Configurations and Startup Procedures
5
I
Sections in this Manual

Sections in this Manual
6NA-series Programmable Terminal Startup Guide (V120)

7
NA-series Programmable Terminal Startup Guide (V120)
CONTENTS
Introduction .............................................................................................................. 1
Relevant Manuals..................................................................................................... 2
Manual Structure...................................................................................................... 3
Sections in this Manual........................................................................................... 5
Terms and Conditions Agreement ......................................................................... 9
Safety Precautions..................................................................................................11
Precautions for Safe Use ...................................................................................... 13
Precautions for Correct Use ................................................................................. 16
Regulations and Standards .................................................................................. 17
Related Manuals..................................................................................................... 19
Terminology............................................................................................................ 23
Revision History..................................................................................................... 24
Section 1 System Configurations and Startup Procedures
1-1 Startup procedures................................................................................................................ 1-2
1-2 System Configurations and Units for Use................................................................................ 1-3
1-3 HMI application to be created.................................................................................................. 1-4
Section 2 HMI Application Basics
2-1 Pages ...................................................................................................................................... 2-2
2-2 Variables................................................................................................................................. 2-3
2-3 Subroutines............................................................................................................................ 2-4
Section 3 Preparing in advance
3-1 Installing Sysmac Studio ...................................................................................................... 3-2
3-2 Assembling a Hardware........................................................................................................3
-3
3-2-1 Wiring Power Supply .................................................................................................................. 3-3
3-2-2 Wiring Ethernet communication cable ........................................................................................3
-4
Section 4 Creating HMI Application and Debugging
4-1 Operation Flowchart.............................................................................................................. 4-2
4-2 Creating a New Project ......................................................................................................... 4-3