Oncam M12 User manual

Evolution 05 Mini Panel-Mount
QUICK START GUIDE
Welcome
The Oncam Evolution Indoor Panel-Mount 360° camera
is designed to be connected to an IP network. Congure
and operate the camera using a standard internet
browser.
Described are the installation and conguration
procedures for a standard surface mount camera
application.
Power Input Power over Ethernet (PoE),
IEEE standard 802.3af
Operating
Temperature 0 to +40°C (-32 to +104°F)
Enclosure Polymer
Weight 0.20 kg (0.44 lbs)
Supplied Parts
• EVO-05 Mini Camera • Torx Screwdriver Bit
• Mounting Kit • Drilling Template
• Quick Start Guide
Mounting & Installation
The Evolution 05 Mini Panel Mount camera provides
quick and easy installations in shallow areas requiring
the EN50155/EN45545 transport certication.
The panel mount camera comes with an RJ45 or M12
plug and spans a 108 mm (4.25-inch) diameter. Three
Torx screws attach the front plate to the base.
Install the Mini Panel camera behind thin at surfaces of
1 to 3 mm (.04 to .12-inch) thickness, such as walls or
ceilings.
NOTICE: Do not over-tighten the Torx screws. Only hand
tighten.
1. Prepare the surface
by using the supplied
drilling template. Drill
holes appropriately
sized for the three
base holes and center
clearance hole.
2. Loosen the three screws
from the front plate
using the Torx tool.
Remove the front plate.
3. Position the camera
behind the panel
surface with the sheye
lens protruding through
the center hole. Align
the surrounding three
holes.
4. Reattach the front plate
using the three Torx
screws. The panel is
sandwiched between
the front plate and the
camera.
5. Apply power and remove the screen protection.
Important
• Read these instructions carefully before
installing or operating this camera.
• This camera should be installed by a qualied
service person and the installation should
conform to local and national regulations.
• This product is only suitable for a surface
mount installation and should not be modied
or adapted for any type of plenum installation.
• Certied as FCC Class A. In a domestic
environment this camera may cause radio
interference in which case the user should
take adequate measures.
DANGER: RISK OF EXPLOSION IF
REPLACING A BATTERY WITH AN
INCORRECT BATTERY TYPE.
MAC Address
Document the camera’s installation location and unique
MAC address. Find the MAC address printed on the
camera label. This information may be needed during the
camera conguration.
M12
EVO-05-LCM
RJ45
EVO-05-LCD
Technical Support
For the A&E, Specication, Installation and User Manual, Software
and Firmware visit:
https://www.oncamgrandeye.com/resources/product-downloads/
Tel: UK [phone]
US [phone]
Email: [email protected]

© Copyright 2020 ONVU Technologies AG. All rights reserved. Oncam is a trading name of ONVU Technologies AG. Specications and congurations subject to change without
notice.
EVO-05-L#D-05 |Panel-Mount Mini |11.2020 |Rev F
Conguring Network Settings
Powering the Camera
Supply power to the camera with PoE IEEE802.3af through
the integrated cable.
IP Settings
In order to use the camera you need the IP address.
There are two IP Settings.
• DHCP server or router to automatically assign unique
valid IP addresses to each camera.
• A manually congured network using static IP
addresses.
If your network has a DHCP server, go to First Time Camera
Access.
Should a DHCP server not be available, the camera adopts the
default static IP address 192.168.0.200. You will then need to
manually assign each camera with a new unique IP address.
Note: See the camera’s User Manual and Camera
Conguration Tool User Manual for IP Setting.
First Time Camera Access
Web Browser
1. If you know the IP address of the camera, enter this
into the address bar of your web browser (Internet Explorer, Edge,
Firefox or Chrome). The camera should be on the same network.
2. Create an Admin username and password.
Notes:
Internet Explorer 11 is required to view live camera images in the browser.
All other browsers can be used for conguration purposes only.
Ensure you have the latest VLC Media Player (http://www.videolan.org/vlc/
index.html) for viewing camera images on the web interface.
Camera Conguration Tool
1. Select a camera from the camera list
2. Select your browser to open the web interface.
3. Click OK on the authentication pop up. You will then be prompted
to create and set an Admin username and password to access the
camera.
Download our FREE ONVU360 Pro mobile application and
put the 360-degree experience right at your ngertips.
Scan the QR Code to get it now!
Android iOS
Using the Camera Conguration Tool
Go to the Oncam website (https://www.oncamgrandeye.com/
resources/camera-cong-tool/) to download the latest version of
the Camera Conguration tool and corresponding User Manual.
The Camera Conguration tool quickly nds the IP and MAC
addresses of all Oncam Evolution cameras connected to
the network. It also allows you to change network settings,
congure the system and perform software updates on multiple
cameras. Initiate a new scan by clicking the Full Discover button
Start the application by clicking the CameraCongurationTool
icon found on your desktop or from the program list (under
Oncam Grandeye). The software scans the network and provides
a list of all connected Oncam Evolution cameras.
Note: Some functions in this tool require a username and
password. If accessing the camera for the rst time, an
administrator username and password will need to be set.