OneTouch ONETOUCH SELECT - CONTROL SOLUTION User manual

O ner’s Booklet
Manual del propietario
Blood Glucose Monitoring System
Easy to Use. Results You Can Trust.
TM
Sistema de control de glucosa en sangre
Fácil de usar. Resultados confiables.

ii
Welcome to the OneTouch® family!
OneTouch®is committed to creating a world without limits for people
with diabetes.
The OneTouch®Select™Meter makes it simple to get a test result and
review past results. This owner’s booklet will help you learn how to use
your meter properly. Please read it carefully.
f you need assistance, please contact LifeScan Customer Service at
1 800 227-8862 (available 24 hours a day, seven days a week). Please
also visit www.LifeScan.com for more information.
NOTE: Before testing, read this owner’s booklet carefully.

ii
Table of Contents
Setting up your system g. 1
Starting the test process g. 8
Getting a blood sample g. 12
Applying blood and reading results g. 24
Reviewing past results and averages g. 32
Control solution testing g. 38
Caring for your system g. 44
Understanding error and other messages g. 50
Detailed information about your system g. 59
Index g. 64

iii
Before you begin
Before using this product to test your blood glucose, carefully read this booklet
and the inserts that come with the OneTouch®Select™Test Strips and OneTouch®
Select™and OneTouch®Select™ High Control Solutions. Take note of warnings
and cautions throughout this booklet, which are identified with . Many people
find it helpful to practice the test with control solution before testing with blood
for the first time. See page 38 in the Control solution testing section.
Intended use
The OneTouch®Select™Blood Glucose Monitoring System is intended to be used
for the quantitative measurement of glucose (sugar) in fresh capillary whole
blood. The OneTouch®Select™System is intended for self-testing outside the body
(in vitro diagnostic use) by people with diabetes at home and by health care
professionals in a clinical setting as an aid to monitor the effectiveness of diabetes
control. t should not be used for the diagnosis of diabetes or for testing newborns.
Test principle
Glucose in the blood sample mixes with special chemicals in the test strip and
a small electric current is produced. The strength of this current changes with
the amount of glucose in the blood sample. Your meter measures the current,
calculates your blood glucose level, displays the result, and stores it in its
memory.

 WARNING: K p th m t r and t sting suppli s away from young childr n.
Small it ms such as th batt ry door, batt ry, t st strips, lanc ts, prot ctiv disks
on th lanc ts, and control solution vial cap ar choking hazards. Do Not ing st or
swallow any it ms.
a
b
d
c
iv
The OneTouch®Select™Blood Glucose Monitoring System
Your new OneTouch®Select™System Kit includes:
a OneTouch®Select™Meter (battery included)
b OneTouch®Lancing Device
If another type of lancing device was included,
see the separate instructions that came with
that lancing device.
c OneTouch®AST™Clear Cap
d OneTouch®UltraSoft®Sterile Lancets
e Carrying Case
You will also need OneTouch®Select™ Control Solution and OneTouch®Select™ Test Strips.
Control solution and test strips are sold separately.
Documents in your kit include this owner’s booklet, a starter guide, and a warranty
registration card. f any items are missing from your kit, call Customer Service.

1
Display
T st port
nsert test strip here to
turn meter on for testing
mg/dL is the
pre-set unit of
measure
Up and down buttons
Select or change information
 ndicates
selection
available
using up or
down button
OK button
Turns the meter on/off
Confirms menu selections
Setting up your system
Getting to know your OneTouch®Select™Blood Glucose Meter
and test strips
Front Back
with battery door open Test strip
M t r batt ry Batt ry
door
Confirmation
window
Contact bars
nsert into
test port
Edg to
apply sampl
Data port

2
Turning your meter on
There are two ways to turn your meter on:
To perform a test, insert a test strip as far as it
will go. The meter will briefly perform system
checks, then the display will turn on.
or,
With the meter turned off, press and hold
for two seconds to access MAIN MENU.
Check that the screen shows solid black for two seconds. f it does, the
display is working properly. f the meter does not power on, try changing
the meter battery. See pages 48–49.
Turning your meter off
There are several ways to turn your meter off:
• Press and hold for three seconds.
• Your meter will turn off by itself if left alone for two minutes.
• Go to MAIN MENU and press or to highlight METER OFF, then press .
• Before or after completing a test, remove the test strip. f you advance
from the test result screen to the MAIN MENU by pressing , removing the
test strip will not turn the meter off. Use one of the three methods above.
CAUTION: f you see
any light areas within
the black start-up screen,
there may be a problem
with the meter.
Call Customer Service.
S tting up your syst m

3
S tting up your syst m
Setting the meter language, date and time
You can change many of the settings that came pre-set with your meter.
Before using your meter for the first time or if you change the meter
battery, you should check and update these settings. Make sure you
complete steps 1 through 6 below to ensure your desired settings are
saved.
1. Turn th m t r on, s pag 2
2. G t to th SETTINGS scr n
When using the meter for the first time, or
after changing the meter battery, you will
automatically start in the SETTINGS screen.
n other cases, from the MAIN MENU,
press or to select SETTINGS. To confirm
your selection, press .

S tting up your syst m
The pre-set language, date, time and unit of
measure appear on the display. f they are
correct, press to return to the MAIN MENU.
f the language, date, or time are not correct,
select CHANGE and press .
The display now shows the LANGUAGE screen.
3. Choos a languag
Now press or to highlight the language
of your choice. To confirm your selection,
press .
The display now shows the DATE AND TIME screen.
NOTE: f you select the wrong language, press and hold for three seconds
to turn the meter off. Then, turn the meter back on and re-start from step 1.
4

S tting up your syst m
5
4. S t th dat
n the DATE AND TIME screen,
press or to change the year.
To confirm your selection, press .
Press or to change the month.
To confirm your selection, press .
Press or to change the day.
To confirm your selection, press .

S tting up your syst m
5. S t th tim of day
Press or to set the hour.
To confirm your selection, press .
Press or to set the minutes.
To confirm your selection, press .
Press or to set AM or PM.
To confirm your selection, press .
The display now shows the SETTINGS screen.
NOTE: The date and time formats have been
pre-set. You cannot change these settings.
6

S tting up your syst m
7
6. Confirm your s ttings
OK will be highlighted near the bottom of
the screen. f your settings are correct,
press to confirm and save the settings
and return to the MAIN MENU.
f you want to cancel your settings and start the settings process over
again, press or to highlight CHANGE and press . You will be
returned to the LANGUAGE screen.
 WARNING: Th unit of m asur mg/dL must b display d
h r . If your display shows mmol/L rath r than mg/dL, contact
Custom r S rvic . You cannot chang th unit of m asur . Us
of th wrong unit of m asur may caus you to misint rpr t your
blood glucos l v l, and may l ad to incorr ct tr atm nt.

Starting the test process
Have these things ready when you test your
blood glucose level:
•OneTouch®Select™Meter
• OneTouch®Select™Test Strips
(sold separately)
•Lancing device
•Sterile lancets with protective disks
NOTE:
• Use only OneTouch®Select™Test Strips with
your OneTouch®Select™Meter.
• Make sure your meter and test strips are
about the same temperature before you test.
• Testing must be done within the operating
temperature range (50–111°F). For the most
accurate results, try to test as close to room
temperature (68–77°F) as you can.
• OneTouch®Select™Test Strips are for single
use only. Never re-use a test strip that had
either blood or control solution applied to it.
CAUTION: The
test strip vial contains
drying agents that
are harmful if inhaled
or swallowed and
may cause skin or
eye irritation.
CAUTION: f you
cannot test due to
a problem with your
testing supplies,
contact your health
care professional or
Customer Service.
Failure to test could
delay treatment
decisions and lead
to a serious medical
condition.
8

1. Ch ck th cod on th t st strip vial b for
ins rting th t st strip
Code numbers are used to calibrate your meter
with the test strips you are using.
2. Ins rt a t st strip to turn on th m t r
Start with the meter off. f you have turned the
meter on to change settings or review past results,
turn it off. Remove a test strip from its vial and
recap the vial immediately. With clean, dry
hands, you may touch the test strip anywhere
on its surface. Do Not bend, cut or modify
the test strips in any way. Use each test strip
immediately after removing it from the vial.
nsert the test strip into the test port as shown.
Make sure the three contact bars are facing
you and the arrow is pointing down. Push the
test strip in as far as it will go.
After the black start-up screen appears, the
meter will display the code from your last test.
f a flashing “––” appears instead of a code
number, such as when you are first using the
meter, follow the instructions in Step 3 to
change to a numerical code.
Starting th t st proc ss
9

3. Match th cod on th m t r with th cod
on th t st strip vial
f the code on the meter does not match the
code on the test strip vial, press or to
match the code number on the test strip vial.
The new code number will flash on the display
for three seconds, then briefly stop flashing,
after which the display will advance to the
APPLY SAMPLE screen.
f the codes already match, press to go to
the APPLY SAMPLE screen. When you do not
make a change after five seconds, the display
will advance to the APPLY SAMPLE screen.
The meter is now ready to perform a blood
glucose test.
Starting th t st proc ss
CAUTION: Matching the code on the meter and the code on the
test strip vial is essential to obtaining accurate results. Each time
you test, check to make sure the code numbers match.
10

NOTE:
• f the APPLY SAMPLE screen appears before you are sure the codes
match, remove the test strip, and re-start from step 1, see page 9.
• f you change APPLY SAMPLE to APPLY CONTROL by mistake, press
to change it back to APPLY SAMPLE.
Starting th t st proc ss
11

Overview of the OneTouch® Lancing Device
CAUTION: To reduce the chance of infection:
• Make sure to wash the puncture site with soap and water before sampling.
• Never share a lancet or a lancing device with anyone.
• Always use a new, sterile lancet—lancets are for single use only.
• Keep your meter and lancing device clean. See pages 45–46.
NOTE: f you do not have a OneTouch® Lancing Device, please refer to the
instructions that came with your lancing device.
Getting a blood sample
OneTouch®UltraSoft®Sterile Lancet
Blue cap* (for fingertip sampling)
Depth indicator
*The blue cap and OneTouch®AST ™Clear Cap are also used for depth adjustment.
Cocking control Release utton
OneTouch® AST™Clear Cap*
(for alternate site sampling)
Lancet point
Protective disk
12

Choosing the right sampling site at the right time
The OneTouch®Select™Meter allows you to sample blood from your fingertip,
forearm or palm. Forearm and palm sampling is also referred to as “alternate
site testing” (AST). At times, results obtained at the forearm or palm may be
different from a fingertip measurement. Talk to your health care professional
before you begin using your forearm or palm for sampling.
If you are testing:
Routinely before meals
Prior to or more than two hours after:
• a meal
• a rapid-acting insulin injection or insulin pump bolus
• exercise
When your blood glucose is changing rapidly, such as:
• within two hours after a meal
• within two hours after a rapid-acting
insulin injection or insulin pump bolus, or
• during or within two hours after exercise
When you are concerned about the possibility of
hypoglycemia (low blood sugar)
Fingertip
Fingertip,
forearm, or
palm
G tting a blood sampl
Fingertip,
forearm, or
palm
Use blood
sample from your:
Fingertip
13

14
G tting a blood sampl
CAUTION: Do Not test on your forearm or palm when:
• You think your blood glucose is rapidly falling, such as within two
hours of exercise or a rapid-acting insulin injection or insulin pump
bolus. Testing with a fingertip sample may identify hypoglycemia
or an insulin reaction sooner than testing with a forearm or palm
sample.
• t has been less than two hours after a meal, a rapid-acting insulin
injection or insulin pump bolus, physical exercise, or you think
your glucose level is changing rapidly.
• You are concerned about the possibility of hypoglycemia or an
insulin reaction, such as when driving a car. This is especially
important if you suffer from hypoglycemia unawareness (lack of
symptoms to indicate an insulin reaction).
Remember: Consult with your health care professional before using
your forearm or palm for testing.