Onicon F-4600 Series Operating instructions

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone]
www.onicon.com • [email protected]
F-4600 INLINE ULTRASONIC FLOW METER
With Optional LCD Display
Installation and Operation Guide
06-18
2020-3 / 35874

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
F-4600 With LCD Flow Meter Manual 06/18 - 2020-3 / 35874 Page 2
SAFETY INFORMATION
This meter was calibrated at the factory before shipment. To ensure correct use of the meter, please
read this manual thoroughly.
Regarding this Manual:
• This manual should be passed on to the end user.
• Before use, read this manual thoroughly to comprehend its contents.
• The contents of this manual may be changed without prior notice.
• All rights reserved. No part of this manual may be reproduced in any form without
ONICON’s written permission.
• ONICON makes no warranty of any kind with regard to this material, including, but not
limited to, implied warranties of merchantability and suitability for a particular purpose.
• All reasonable effort has been made to ensure the accuracy of the contents of this manual.
However, if any errors are found, please inform ONICON.
• ONICON assumes no responsibilities for this product except as stated in the warranty.
• If the customer or any third party is harmed by the use of this product, ONICON assumes
no responsibility for any such harm owing to any defects in the product which were not
predictable, or for any indirect damages.
Safety Precautions:
The following general safety precautions must be observed during all phases of installation,
operation, service, and repair of this product. Failure to comply with these precautions or with
specic WARNINGS given elsewhere in this manual violates safety standards of design,
manufacture, and intended use of the product. ONICON Incorporated assumes no liability for the
customer’s failure to comply with these requirements. If this product is used in a manner not
specied in this manual, the protection provided by this product may be impaired.
The following symbols are used in this manual:
!
!
WARNING
Messages identied as “Warning” contain information regarding the personal safety of individuals
involved in the installation, operation or service of this product.
CAUTION
Messages identied as “Caution” contain information regarding potential damage to the product or
other ancillary products.
IMPORTANT NOTE
Messages identied as “Important Note” contain information critical to the proper operation of the
product.
i

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
F-4600 With LCD Flow Meter Manual 06/18 - 2020-3 / 35874 Page 3
TABLE OF CONTENTS
1.0 INTRODUCTION ...................................................................................................... 5
1.1 PURPOSE OF THIS GUIDE ........................................................................... 5
1.2 TYPICAL F-4600 FLOW METER .................................................................. 5
1.3 STANDARD FEATURES AND SPECIFICATIONS........................................ 5
1.4 WORKING ENVIRONMENT ......................................................................... 7
1.5 SERIAL NUMBER .......................................................................................... 7
2.0 UNPACKING ............................................................................................................. 7
2.1 CHECKING THAT YOU HAVE RECEIVED EVERYTHING .......................... 7
3.0 INSTALLATION........................................................................................................ 8
3.1 SITE SELECTION ........................................................................................... 8
3.2 INSTALLING THE FLOW SENSOR .............................................................. 8
3.3 REMOTE MOUNTING THE CALCULATOR ENCLOSURE ........................ 12
3.4 POWER AND SIGNAL WIRING CONNECTIONS ...................................... 13
4.0 F-4600 FLOW START UP AND COMMISSIONING ............................................. 14
4.1 START UP ..................................................................................................... 14
4.1.1 Operating Mode .............................................................................. 15
4.1.2 Additional Display Pages ............................................................... 16
4.2 COMMISSIONING....................................................................................... 17
4.2.1 Commissioning Following Initial Power-up.................................. 17
5.0 DIAGNOSTIC FUNCTIONS ................................................................................... 21
6.0 BACNET MS/TP..................................................................................................... 22
6.1 BACNET®OBJECT TYPES .......................................................................... 22
6.2 PROTOCOL IMPLEMENTATION STATEMENT ........................................ 22
6.3 DEVICE OBJECT .......................................................................................... 23
6.4 ANALOG INPUT(S) ..................................................................................... 24
6.5 ANALOG VALUE(S) .................................................................................... 25
6.6 BINARY VALUE(S) ...................................................................................... 26
6.7 MULTI STATE VALUE.................................................................................. 27
6.8 TREND LOG MULTIPLE............................................................................... 28
7.0 MODBUS®........................................................................................................ 29
7.1 MODBUS®MEMORY MAP ......................................................................... 33
7.2 DIAGNOSTIC FUNCTION CODE................................................................. 33
7.3 REPORT SLAVE ID FUNCTION CODE........................................................ 34

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
F-4600 With LCD Flow Meter Manual 06/18 - 2020-3 / 35874 Page 4
8.0 AUXILIARY INPUTS AND OUTPUTS ................................................................... 35
8.1 DETERMINING AUXILIARY INPUT & OUTPUT CONFIGURATION........ 35
8.2 AUXILIARY INPUTS .................................................................................... 35
8.3 AUXILIARY OUTPUTS ................................................................................ 36
8.3.1 Pulse Outputs.................................................................................. 36
8.4 ANALOG OUTPUTS .................................................................................... 37

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
F-4600 With LCD Flow Meter Manual 06/18 - 2020-3 / 35874 Page 5
SECTION 1.0: INTRODUCTION
1.1 PURPOSE OF THIS GUIDE
The purpose of this guide is to provide installation and commissioning procedures, and basic
operating and servicing instructions for the ONICON F-4600 ow meter with optional LCD
display.
1.3 STANDARD FEATURES AND SPECIFICATIONS
• Detachable enclosure with alphanumeric display and user interface
• Three 2-wire signal ports can be congured as pulse input or outputs. One of the ports can
be congured as an analog output.
!
WARNING
Only qualied service personnel should attempt to install or service this product. Serious injury
may result from the improper installation or use of this product.
1.2 TYPICAL F-4600 FLOW METER
The F-4600 inline ow meter utilizes direct path wetted ultrasonic transducers for measuring
the volumetric ow and temperature of liquids in a wide variety of applications. The meter is
provided with a detachable enclosure with a built-in user interface/display.
POWER
24 V AC/DC
Input Power
Input and Output
Signals and
BACnet / MODBUS

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
F-4600 With LCD Flow Meter Manual 06/18 - 2020-3 / 35874 Page 6
NOTE: Specications subject to change without notice
GENERAL SPECIFICATIONS
ACCURACY
FLOW
± 1% of reading over 25:1 turndown
± 2% of reading over 100:1 turndown
Repeatability: ≤ ± 0.2%
OVERALL FLOW RANGE
500:1 turndown
SENSING METHOD
Direct beam path wetted ultrasonic sensors utilizing
differential transit time velocity measurement
METER SIZES (Nominal diameter in inches)
½, ¾, 1, 1¼, 1½, 2 and 2½
PIPING SYSTEM CONNECTIONS
Male NPT threads
2½” meter provided with ANSI Class 150 raised face
anges
Optional PN16 or ANSI Class 300 raised face anges
FLUID TEMPERATURE RANGE
32°F to 250°F
AMBIENT TEMPERATURE RANGE
-13°F to 131°F
MAXIMUM OPERATING PRESSURE
400 PSI
PRESSURE DROP
Less than 1 psi at 4 ft/sec, decreasing at lower velocities
POWER SUPPLY REQUIREMENTS
20-28V AC/DC, 50/60 Hz, 5 VA maximum
PULSE INPUTS, OUTPUTS, and ANALOG OUTPUT
The three 2-wire signal ports can be congured as pulse inputs or
outputs. One of the ports can be congured as an analog output.
Isolated totalizing pulse inputs for use with sinking open
collector or dry contact outputs
Input rating: 30 VDC, 10 mA maximum
Pulse duration: 50 ms minimum
Isolated totalizing solid state contact closure pulse outputs may
be programmed for energy, volume, alarm indication or coil
indication (MODBUS RTU only)
Contact ratings: 50 mA, 30 V
Contact pulse duration: 50, 100, 500 or 1000 ms (500ms
default)
Analog 4-20 mA, 0-5 V or 0-10 V output for ow rate or
temperature
NETWORK CONNECTION
Isolated RS485 serial interface
COMMUNICATION PROTOCOLS
BACnet MS/TP per ASHRAE Standard 135.1: 2009
MODBUSR RTU
NETWORK CONFIGURATION & ADDRESSING
Baud Rates: 4800, 9600, 19200, 38400, 76800, or 115200
Device Address Range: 1 – 127 (1 - 247 MODBUS)
Device Instance Range: 1 – 4,194,303 (BACnet only)
Parity: None, Even, Odd (MODBUS RTU only)
APPROVALS
FCC: Part 15, Subpart B
CE
Conforms to ANSI/NSF 61 & 372
BTL Certied to ASHRAE 135:2009

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
F-4600 With LCD Flow Meter Manual 06/18 - 2020-3 / 35874 Page 7
1.4 WORKING ENVIRONMENT
The F-4600 with optional LCD display was designed for installation and use indoors or outdoors
in protected spaces, or in residential, commercial and light industrial environments that are free
of corrosive liquids and fumes, temperature extremes and excess vibration.
The operating ambient air temperature range is -13°F to 131°F. The electrical power should be
relatively clean, free of excess high frequency noise and large voltage transients.
1.5 SERIAL NUMBER
Serial Number
The serial number of your F-4600 is located on the side of the enclosure. The serial number
is a unique identier for the product. Please have this number available when contacting
ONICON for assistance.
SECTION 2.0: UNPACKING
The F-4600 is generally shipped in one package unless optional hardware or equipment is ordered.
Notify the freight carrier and ONICON if any items are damaged in transit.
2.1 CHECKING THAT YOU HAVE RECEIVED EVERYTHING
The following items have been provided with your F-4600 Flow Meter:
Two line size process connection meter couplings* with male NPT threads and sealing gaskets
(shipped attached to meter)
One F-4600 Meter Installation and Operation Guide
One F-4600 Meter Certicate of Calibration
One Remote Mount Bracket
Please notify ONICON if any of these items are missing.
*NOTE: The 2½” version of the meter is provided with anges.

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
F-4600 With LCD Flow Meter Manual 06/18 - 2020-3 / 35874 Page 8
SECTION 3.0: INSTALLATION
The F-4600 Flow Meter should be installed by experienced plumbers, electricians, and others with
related knowledge and experience in the heating, cooling, and uid metering elds. ONICON technical
support personnel are available via telephone or e-mail to provide technical assistance before, during
and after installation. On-site eld engineering, installation, and service are also available at an
additional cost. The installer should use good trade practices and must adhere to all state and local
building, or other, applicable codes.
Before you begin, clean the external surfaces of all pipes at the installation site so that it is free of
debris, foreign matter, solids, leak inhibitors, and chemically aggressive substances. Flush the entire
system so that it is free of ux, solder, pipe and tube cuttings and any other free moving debris.
3.1 SITE SELECTION
Careful attention to the site selection for the meter will help the installers with the initial
installation, reduce start-up problems, and make future maintenance easier. For example, do not
install the meter where it will be difcult for personnel to perform periodic maintenance. When
selecting a site, consider the criteria under Section 1.4: WORKING ENVIRONMENT, as well as
the information below.
The following limitations apply to the installation of the meter:
• The ow meter must be correctly oriented with respect to the direction of ow in the pipe.
Meters installed with reversed ow will not function.
• The F-4600 is provided with a 4.9 ft (1.5 m) cable for the detachable enclosure. Do not alter
this cable length. Doing so will void the calibration and may invalidate the warranty.
• The maximum operating pressure for the ow meter is 400 psi.
• At uid temperatures above 212°F, the enclosure should be remote mounted.
• Do not install the meter in close proximity to strong sources of electromagnetic interference
(e.g. electric motors, VFD’s, uorescent light xtures, etc.)
3.2 INSTALLING THE FLOW SENSOR
Before you install the meter, the entire piping system should be ushed and free of debris. Please
refer to the diagrams on the following page when selecting the installation location. Upstream
straight unobstructed pipe requirements vary considerably based on nature of the upstream
obstructions. As a general rule, ONICON recommends a minimum of 10 diameters of straight
unobstructed pipe whenever possible; keeping in mind that it is always recommended that the
meter be located with as much straight pipe upstream as possible. Recommended minimum
straight run requirements are provided on the following page.

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
F-4600 With LCD Flow Meter Manual 06/18 - 2020-3 / 35874 Page 9
A. This is a recommended position for the ow sensor.
B. Avoid installation locations where air can become trapped in the piping system.
C. This is an acceptable installation location for closed loop pressurized systems.
D. Do not install the sensor downstream of modulating valves or partially open valves.
Fully open isolation valves (e.g. ball valves) are OK.
E. Do not install the ow sensor at the inlet of a pump. To prevent cavitation, the
minimum operating pressure at the inlet of the meter must always exceed the pressure
drop across the meter. Refer to Appendix A-3 for calculating pressure the drop at
different ow rates.
F. Avoid installing the meter downstream of multiple bends out of plane with each other
where there are less than 10 diameters of straight unobstructed pipe between bends.
A
B
C
D & E
F
Flow Direction
Flow Direction
STRAIGHT RUN REQUIREMENTS
Upstream Obstruction
Minimum Upstream Straight Run Required (Pipe Diameters)
Meter Size
0.5 - 1.0" 1.25 - 2.5"
Single Elbow 0 0
Expander / Reducer 0 0
Coil, Upstream 3 3
Isolation Valve, 2 Position 3 5
Control Valve 10 15
Notes:
1 Straight run is based on use of manufacturer provided couplings
2 Avoid the following obstructions where possible: Modulating valves, pump discharge, multiple
elbows out of plane.
A

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
F-4600 With LCD Flow Meter Manual 06/18 - 2020-3 / 35874 Page 10
Flow Direction The sensor port is always on
the downstream end of meter.
Retaining Nut SealCoupling
The ow sensor is installed with threaded meter couplings and at sealing gaskets as shown
below. Orient the sensor body by aligning the ow direction arrow with the direction of ow
in the pipe.
Model Meter Size Min.
Compression
Min. Turn Past
Initial Contact
Degrees of
Rotation
F-4600-050 ½” 30% 1/2 180°
F-4600-340 ¾” 30% 1/3 120°
F-4600-341 ¾” 30% 1/3 120°
F-4600-010 1” 30% 2/5 140°
F-4600-011 1” 30% 2/5 140°
F-4600-130 1¼” 30% 2/5 140°
F-4600-150 1½” 30% 4/9 160°
F-4600-200 2” 30% 1/2 180°
INSTALLING METER COUPLINGS
• Inspect seating surfaces on the meter’s body and tail piece prior to assembly. Surfaces should be
clean and free of any burs or markings.
• Install the gasket in tail piece. Thread union onto meter’s body, by hand, until gasket and mating
surfaces make rst contact. Mark coupling nut and tail piece.
• Place a corresponding mark on the coupling nut, # of degrees (based on table above) counter
clockwise. Hold meter body while rotating coupling nut clockwise until marks line up. DO NOT
over-tighten.
• Repeat process on opposite side of ow meter body.
NOTE: Torque setting is not an accurate means of gaging compression on gasket due to the lack of
resilience in the gasket material.
• Pressurize system and check for leaks. If any leak is present, DO NOT over-tighten. Relieve pressure
and loosen coupling nuts. Remove and inspect the gasket for damage. Repeat installation process.

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
F-4600 With LCD Flow Meter Manual 06/18 - 2020-3 / 35874 Page 11
Slide calculator
enclosure to
remove from
sensor mounting
brackets
Slide Enclosure
Mounting Tracks
Retaining
Screw
Retaining
Screw
IMPORTANT NOTE
When installing the meter in a vertical pipe with upward ow, you must rotate the enclosure
back plate 180° when rotating the display 90°. To accomplish this, temporarily remove the 4
cover screws and rotate the backing plate.
i
For ½ - 1” meter sizes the calculator enclosure may be rotated around the axis of the ow sensor
into three different positions. To rotate, temporarily slide the enclosure off the ow sensor
mounting brackets. Remove the two retaining screws and reposition the mounting brackets
as required. Reinstall the enclosure with the display properly oriented for viewing. Mounting
tracks on the back of the enclosure allow for mounting in any orientation.
Orient the ½ - 1” meters as shown below. The meter may be installed with upward or downward
ow in vertical pipes in closed loop pressurized systems. Avoid any installation locations where
the pipe may not be completely full.
Do not orient meter as shown above
Back View Side View
Meter Sizes ½” to 1”
Preferred Orientation for Horizontal Housing
Side View

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
F-4600 With LCD Flow Meter Manual 06/18 - 2020-3 / 35874 Page 12
ON I CON
Flow and Energy Measurement
Side View
Do not orient meter as shown above
Meter Sizes 1¼” - 2½”
Preferred Orientation for Horizontal Housing
Front ViewSide ViewSide View
Slot for Pipe
Clamps
0.219”
Slide Tracks
Slide Tracks
3.3 REMOTE MOUNTING THE ENCLOSURE
The F-4600 with display is provided with a mounting bracket and the cables required for remote
mounting up to 5 Ft (1.5 m) length. This cable length must not be altered.
The remote mounting bracket has two 0.219” mounting holes designed to accommodate #10
screws. It also has parallel slots that allow for the use of pipe clamps when mounting the
enclosure on a stanchion or pipe. The bracket may be used as a template for marking locations for
holes.

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
F-4600 With LCD Flow Meter Manual 06/18 - 2020-3 / 35874 Page 13
Remote (internal) Temperature Sensor
Name Terminal # Description
1000 ohm TB3-1 RTD signal wire
Not used TB3-2 No Connection
Not used TB3-3 No Connection
1000 ohm RTD TB3-4 RTD signal wire
* This sensor must be in the same
pipe as the ow sensor.
i
IMPORTANT NOTE
Open isolation valves, leak test and purge the piping system of air prior to wiring the meter.
Power and Signal Inputs (18 - 22 AWG wire)
Name Terminal # Description
24V AC/DC (+) TB1-1 20 - 28 VAC/DC, 50/60 Hz, 5 VA max.
24V AC/DC Common (-) TB1-2
Aux I/O # 1 (+) TB1-3 Congured as either input or output at factory.
Output rating
Pulse Output:
Pulse duration: Selectable 50, 100, 500, or 1,000 ms
Contact ratings: 50 mA, 30 VDC max.
Analog Output (AUX I/O # 3 only):
Selectable: 4-20 mA, 0-10 VDC, 0-5 VDC
Input rating
For use with open collector sinking and dry contact
outputs only.
Pulse duration: 50 ms min.
Sinking Current: 10 mA max.
Aux I/O # 1 (-) TB1-4
Aux I/O # 2 (+) TB1-5
Aux I/O # 2 (-) TB1-6
Aux I/O # 3 (+) TB1-7
Aux I/O # 3 (-) TB1-8
RS485 (20 - 24 AWG wire)
Name TB4 Description
RS485 B (+) TB4-1
RS485 Unit Load = 1/4
Recommended Devices
per Segment = 32
RS485 A (-) TB4-2
RS485 Common TB4-3
RS485 Termination Resistor
Name JMP5 Description
120 ohm Position 1 Jumper Position 1 & 2
= 120 ohms
120 ohm Position 2
None Position 3 Jumper Position 2 & 3
= No Termination
3.4 POWER AND SIGNAL WIRING CONNECTIONS
The F-4600 is provided with 4 glands on the right hand side of the enclosure for power and
signal cables. Each includes a strain relief for securing the cabling and a sealing cap. The power
cable should enter the enclosure through the bottom gland. Do not remove the sealing caps from
unused cable glands.
1 2 3 4 5 6 7 8 1 2 3
10
9
H5 SERIAL
TB3 TB2
H3
4321 4321
1 2 1 2 1 2 1 2
TB8 TB7 TB6 TB5 SW6 SW7 SW2 SW1
C34
C33
R6
DS3
R8 H2 SERIAL
2
1
GRD
DS2
R60
3
JMP5
1
CAUTION
INSTALL + SIDE UP
CR2032 BATTERY
BAT1
Internal RTD
(Flow)
External RTD
24V AC/DC (+) 24V COMMON (-) AUX 1 (+) AUX 1 (-) AUX 2 (+) AUX 2 (-) AUX 3 (+) AUX 3 (-) RS485 (+) RS485 (-) RS485 COMMON
TB1 TB4
COMMISSIONING MICROPROCESSOR
RESET
RS485 Termination
1 - 2 = 120 Ω
2 - 3 = None
System-40-BAC Enclosure Label
1048 / 33354 02-15
11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone]
www.onicon.com • [email protected]
Actual Size - 4.125” x 2.875”
Cutline

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
F-4600 With LCD Flow Meter Manual 06/18 - 2020-3 / 35874 Page 14
SECTION 4.0: F-4600 START-UP AND COMMISSIONING
Alarm Indication
Unit of Measure
4.1 START-UP
When power is rst applied to the meter the display will be illuminated and the following start
screen will appear. Momentarily press SEL (select) to access the operating mode (User Screens)
display pages.
Verify that the meter is functional by stepping through the display pages and conrming the ow
rate and temperature data is within expected norms. Momentarily press NEXT or BACK to change
the displayed page. A complete list of the display pages is provided on the following page.
When reviewing the displayed data, note the factory programmed engineering units on each display
page (e.g. gallons, gpm, °F). Note any changes that may be necessary. These will need to be made
during commissioning.
To return to the commissioning mode from the user screens, momentarily press MENU. The
following page will appear. Momentarily press EXIT to return to the start screen.

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
F-4600 With LCD Flow Meter Manual 06/18 - 2020-3 / 35874 Page 15
*
*
*
* Will only appear if Aux I/O was congured at factory for pulse input.
4.1.1 Operating Mode Display Pages

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
F-4600 With LCD Flow Meter Manual 06/18 - 2020-3 / 35874 Page 16
4.1.2 Additional Display Pages
EXIT
NEXT
SEL
More Totals
!Alarms
Diagnostic
Meter Data
YTD Volume
0
gallons
EXIT
NEXT
MENU
Prev Yr Volume
0
gallons
EXIT
NEXT
MENU
YTD Volume Total resets at
12:01 AM on January 1st
Prev. Yr Volume Total updates at
12:01 AM on January 1st
Alarms
Empty Pipe
High Flow
EXIT
NEXT
MORE
Alarms
More Totals
Signal Strength
0
0-Empty Pipe
EXIT
NEXT
MENU
Transit Time
00.00000 Up
00.00000 Dn
EXIT
NEXT
MENU
Diagnostics
Speed of Sound
0
ft/s
EXIT
NEXT
MENU
Serial Number
0
EXIT
NEXT
MENU
MeterCong
0
EXIT
NEXT
MENU
Meter Data
Manufacturing Date
0000/00
Year/Month
EXIT
NEXT
MENU
Firmware Rev
App: 0.0.0
Boot: 0.0.0
DA: 0.0.0
DB: 0.0.0
Pre: 0.0.0
EXIT
NEXT
MENU
Calibration Date
0000/00
Year/Month
EXIT
NEXT
MENU
Alarm Messages
High Flow
Empty Pipe
Comm Error
System Fault

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
F-4600 With LCD Flow Meter Manual 06/18 - 2020-3 / 35874 Page 17
4.2 COMMISSIONING
The last step in the installation process is commissioning the meter. Commissioning is a 2 step
process. The rst step is to review the mechanical installation to conrm that the ow meter is
properly located in the piping system. The second step is a review of the meter program settings.
Both steps must be completed in order to nish the installation. A simple commissioning
checklist is shown below. A copy of this may be found online at www.onicon.com/F-4600.html.
Commissioning Checklist
Part 1 Mechanical installation
Conrm that the ow sensor is properly located in the piping system (Sec. 3.1 & 3.2).
Conrm that the ow sensor is properly oriented with respect to ow direction (Sec. 3.2).
Part 2 Programming
Verify that the Units of Measure Settings in the meter are correct (Sec. 4.1).
Conrm that there are no alarm indications and the meter is functional (Sec. 4.1.2).
4.2.1 Commissioning Following Initial Power-up
During initial power-up, the following display pages will appear when the commissioning
option is selected. The settings shown on the following page allow the installer to set
MODBUS®or BACnet®parameters, and the date and time. If the factory pre-programmed
engineering units for ow and temperature are correct, press SAVE to exit commissioning
once the correct date has been set. Momentarily press NEXT if you wish access the
remaining commissioning mode display pages as shown.

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
F-4600 With LCD Flow Meter Manual 06/18 - 2020-3 / 35874 Page 18
Commissioning
Remaining parameters branch
depending on model number.
See following pages.
Exit
Next
Set Meter
Press Next to complete
Install or adjust settings
Exit
Next
Edit
Aux Cong
1 In 1 Out 1 Analog
Exit
Next
Edit
Num Aux Inputs
1
Exit
Next
Edit
Aux Input 1
Counts
Exit
Next
Edit
Pulsed Output 2
Volume Total
Exit
Next
Edit
Pulse Timing
Pulse 500ms
Exit
Next
Edit
Volume Scaling
x10
Exit
Next
Edit
Analog Signal
4-20 mA
Exit
Next
Edit
Analog Output
Volume Rate
Exit
Next
Edit
Analog Output Max
00
Exit
Next
Edit
000.000
Exit
Next
Edit
Set Meter
Press NEXT to edit units
of measure
SAVE completes install
with current settings
Exit
Next
Edit
Protocol
Modbus
Exit
Next
Edit
Modbus Address
017
0-247
Exit
Next
Edit
Baud Rate
9600
Exit
Next
Edit
Parity
Odd Even None
None
Exit
Next
Edit
Stop Bits
1
1 2
Exit
Next
Edit
Set Time
HH:MM:SS
Exit
Next
Edit
Set Date
YYYY/MM/DD
Exit
Next
Edit
Set Meter
Press NEXT edits units
of measure
SAVE Completes install
with current settings
Exit
Next
Edit
Protocol
BACnet
Exit
Next
Edit
BACnet Address
1
0-127
Exit
Next
Edit
Instance Number
57017
0-4194302
Exit
Next
Edit
Baud Rate
38400
Exit
Next
Edit
Medium
Water
Exit
Next
Edit Select Units
Flow
gpm
Exit
Next
Edit
Volume
gallons
Exit
Next
Edit
Set Meter
Deg F
Select Units
Select Type
Select Mulitiplier
Select Signal
Select Type
Analog Output Units
Analog Output Units
Select Units
Analog Output Min

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
F-4600 With LCD Flow Meter Manual 06/18 - 2020-3 / 35874 Page 19
EXIT
NEXT
EDIT
Aux Input 1
BACK
NEXT
SAVE
Set Meter
Counts
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Num Aux Inputs
3
EXIT
NEXT
EDIT
Aux Input 2
Counts
EXIT
NEXT
EDIT
Aux Input 3
Counts
BACK
NEXT
SAVE
Set Meter
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Pulse Timing
Pulse 500 ms
EXIT
NEXT
EDIT
Pulsed Output 1
Volume Total
Select Type
EXIT
NEXT
EDIT
Pulsed Output 2
Volume Total
Select Type
EXIT
NEXT
EDIT
Pulsed Output 3
Alarm
Select Type
EXIT
NEXT
EDIT
Pulse 1 Scaling
x1
Select Multiplier
EXIT
NEXT
EDIT
Pulse 2 Scaling
x1
Select Multiplier
EXIT
NEXT
EDIT
Pulse 3 Scaling
x1
Select Multiplier
EXIT
NEXT
EDIT
Aux Input 1
Counts
EXIT
NEXT
EDIT
Num Aux Inputs
2
EXIT
NEXT
EDIT
Aux Input 2
Counts
EXIT
NEXT
EDIT
Pulse Timing
Pulse 500 ms
EXIT
NEXT
EDIT
Pulsed Output 1
Volume Total
Select Type
EXIT
NEXT
EDIT
Pulse 1 Scaling
x1
Select Multiplier
BACK
NEXT
SAVE
Set Meter
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Aux Input 1
Counts
EXIT
NEXT
EDIT
Num Aux Inputs
1
EXIT
NEXT
EDIT
Pulsed Output 1
Volume Total
Select Type
EXIT
NEXT
EDIT
Pulsed Output 2
Volume Total
Select Type
EXIT
NEXT
EDIT
Pulse Timing
Pulse 500 ms
EXIT
NEXT
EDIT
Pulse 1 Scaling
x1
Select Multiplier
EXIT
NEXT
EDIT
Pulse 2 Scaling
x1
Select Multiplier
BACK
NEXT
SAVE
Set Meter
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Aux Input 1
Counts
EXIT
NEXT
EDIT
Num Aux Inputs
2
EXIT
NEXT
EDIT
Aux Input 2
Counts
BACK
NEXT
SAVE
Set Meter
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Analog Signal
4-20 mA
EXIT
NEXT
EDIT
Analog Output
Volume Rate
EXIT
NEXT
EDIT
Analog Output Max
500.000
Analog Output Units
Select Signal
Select Type
EXIT
NEXT
EDIT
Analog Output Min
000.000
Analog Output Units
EXIT
NEXT
EDIT
Pulsed Output 1
Energy Total
Select Type
EXIT
NEXT
EDIT
Pulsed Output 2
Volume Total
Select Type
EXIT
NEXT
EDIT
Pulse Timing
Pulse 500 ms
EXIT
NEXT
EDIT
Pulse 1 Scaling
x1
Select Multiplier
EXIT
NEXT
EDIT
Pulse 2 Scaling
x1
Select Multiplier
BACK
NEXT
SAVE
Set Meter
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Analog Signal
4-20 mA
EXIT
NEXT
EDIT
Analog Output
Volume Rate
EXIT
NEXT
EDIT
Analog Output Max
500.000
Analog Output Units
Select Signal
Select Type
EXIT
NEXT
EDIT
Analog Output Min
000.000
Analog Output Units
EXIT
NEXT
EDIT
Aux Input 1
Counts
EXIT
NEXT
EDIT
Num Aux Inputs
1
EXIT
NEXT
EDIT
Pulsed Output 1
Energy Total
Select Type
EXIT
NEXT
EDIT
Pulse Timing
Pulse 500 ms
EXIT
NEXT
EDIT
Pulse 1 Scaling
x1
Select Multiplier
BACK
NEXT
SAVE
Set Meter
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Analog Signal
4-20 mA
EXIT
NEXT
EDIT
Analog Output
Volume Rate
EXIT
NEXT
EDIT
Analog Output Max
500.000
Analog Output Units
Select Signal
Select Type
EXIT
NEXT
EDIT
Analog Output Min
000.000
Analog Output Units
NEXT
None
Instance Number
NEXT
EDIT
NEXT
NEXT
F
Set Meter
NEXT
gpm
NEXT
38400
SAVE
Medium
NEXT
NEXT
HH:MM:SS
0 - 255
EXIT
EXIT
EXIT
EDIT
EXIT
Odd Even None
57017
EDIT
DONE
NEXT
NEXT
Modbus Address
EDIT
EDIT
Short Commissioning
Next to complete Install
or adjust
settings.
EDIT
gallons
EDIT
Parity
Set Meter
EDIT
EDIT
NEXT edits units of
measure
SAVE completes install
with current settings
NEXT
EXIT
Protocol
NEXT
DONE
0 - 4194303
Temperature
017
Set Date
Volume
Select Units
Short Commissioning
Protocol
Select Units
NEXT
EDIT
EDIT
Baud Rate
1
BACnet Address
EDIT
BACK
NEXT
DONE
EDIT
Set Time
Flow
Modbus
EDIT
EXIT
NEXT
DONE
0 - 247
Water
Select Units
Units of Measure & Aux I/O
Configuration Settings
Stop Bits
NEXT
EXIT
EXIT
BACnet
EXIT
EXIT
9600
YYYY:MM:DD
1 2
1
DONE
Baud Rate
NEXT
EDIT
DONE
To determine how the auxiliary inputs and outputs are congured on your F-4600,
reference the model number string of your meter:
Meter Model Number Coding = F-4600-AAA-BCD-EF
F = Analog & Pulse Input / Output Conguration (Not eld congurable)
6 = 1 analog output, 1 pulse input & 1 pulse output
9 = 1 analog output & 1 pulse output
F = 0 F = 1 F = 2
(Continued from Page 18) (Continued from Page 18) (Continued from Page 18)

11451 Belcher Road South, Largo, FL 33773 • USA • Tel [phone] • Fax [phone] • [email protected]
F-4600 With LCD Flow Meter Manual 06/18 - 2020-3 / 35874 Page 20
EXIT
NEXT
EDIT
Aux Input 1
BACK
NEXT
SAVE
Set Meter
Counts
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Num Aux Inputs
3
EXIT
NEXT
EDIT
Aux Input 2
Counts
EXIT
NEXT
EDIT
Aux Input 3
Counts
BACK
NEXT
SAVE
Set Meter
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Pulse Timing
Pulse 500 ms
EXIT
NEXT
EDIT
Pulsed Output 1
Volume Total
Select Type
EXIT
NEXT
EDIT
Pulsed Output 2
Volume Total
Select Type
EXIT
NEXT
EDIT
Pulsed Output 3
Alarm
Select Type
EXIT
NEXT
EDIT
Pulse 1 Scaling
x1
Select Multiplier
EXIT
NEXT
EDIT
Pulse 2 Scaling
x1
Select Multiplier
EXIT
NEXT
EDIT
Pulse 3 Scaling
x1
Select Multiplier
EXIT
NEXT
EDIT
Aux Input 1
Counts
EXIT
NEXT
EDIT
Num Aux Inputs
2
EXIT
NEXT
EDIT
Aux Input 2
Counts
EXIT
NEXT
EDIT
Pulse Timing
Pulse 500 ms
EXIT
NEXT
EDIT
Pulsed Output 1
Volume Total
Select Type
EXIT
NEXT
EDIT
Pulse 1 Scaling
x1
Select Multiplier
BACK
NEXT
SAVE
Set Meter
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Aux Input 1
Counts
EXIT
NEXT
EDIT
Num Aux Inputs
1
EXIT
NEXT
EDIT
Pulsed Output 1
Volume Total
Select Type
EXIT
NEXT
EDIT
Pulsed Output 2
Volume Total
Select Type
EXIT
NEXT
EDIT
Pulse Timing
Pulse 500 ms
EXIT
NEXT
EDIT
Pulse 1 Scaling
x1
Select Multiplier
EXIT
NEXT
EDIT
Pulse 2 Scaling
x1
Select Multiplier
BACK
NEXT
SAVE
Set Meter
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Aux Input 1
Counts
EXIT
NEXT
EDIT
Num Aux Inputs
2
EXIT
NEXT
EDIT
Aux Input 2
Counts
BACK
NEXT
SAVE
Set Meter
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Analog Signal
4-20 mA
EXIT
NEXT
EDIT
Analog Output
Volume Rate
EXIT
NEXT
EDIT
Analog Output Max
500.000
Analog Output Units
Select Signal
Select Type
EXIT
NEXT
EDIT
Analog Output Min
000.000
Analog Output Units
EXIT
NEXT
EDIT
Pulsed Output 1
Energy Total
Select Type
EXIT
NEXT
EDIT
Pulsed Output 2
Volume Total
Select Type
EXIT
NEXT
EDIT
Pulse Timing
Pulse 500 ms
EXIT
NEXT
EDIT
Pulse 1 Scaling
x1
Select Multiplier
EXIT
NEXT
EDIT
Pulse 2 Scaling
x1
Select Multiplier
BACK
NEXT
SAVE
Set Meter
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Analog Signal
4-20 mA
EXIT
NEXT
EDIT
Analog Output
Volume Rate
EXIT
NEXT
EDIT
Analog Output Max
500.000
Analog Output Units
Select Signal
Select Type
EXIT
NEXT
EDIT
Analog Output Min
000.000
Analog Output Units
EXIT
NEXT
EDIT
Aux Input 1
Counts
EXIT
NEXT
EDIT
Num Aux Inputs
1
EXIT
NEXT
EDIT
Pulsed Output 1
Energy Total
Select Type
EXIT
NEXT
EDIT
Pulse Timing
Pulse 500 ms
EXIT
NEXT
EDIT
Pulse 1 Scaling
x1
Select Multiplier
BACK
NEXT
SAVE
Set Meter
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Analog Signal
4-20 mA
EXIT
NEXT
EDIT
Analog Output
Volume Rate
EXIT
NEXT
EDIT
Analog Output Max
500.000
Analog Output Units
Select Signal
Select Type
EXIT
NEXT
EDIT
Analog Output Min
000.000
Analog Output Units
NEXT
None
Instance Number
NEXT
EDIT
NEXT
NEXT
F
Set Meter
NEXT
gpm
NEXT
38400
SAVE
Medium
NEXT
NEXT
HH:MM:SS
0 - 255
EXIT
EXIT
EXIT
EDIT
EXIT
Odd Even None
57017
EDIT
DONE
NEXT
NEXT
Modbus Address
EDIT
EDIT
Short Commissioning
Next to complete Install
or adjust settings.
EDIT
gallons
EDIT
Parity
Set Meter
EDIT
EDIT
NEXT edits units of
measure
SAVE completes install
with current settings
NEXT
EXIT
Protocol
NEXT
DONE
0 - 4194303
Temperature
017
Set Date
Volume
Select Units
Short Commissioning
Protocol
Select Units
NEXT
EDIT
EDIT
Baud Rate
1
BACnet Address
EDIT
BACK
NEXT
DONE
EDIT
Set Time
Flow
Modbus
EDIT
EXIT
NEXT
DONE
0 - 247
Water
Select Units
Units of Measure & Aux I/O
Configuration Settings
Stop Bits
NEXT
EXIT
EXIT
BACnet
EXIT
EXIT
9600
YYYY:MM:DD
1 2
1
DONE
Baud Rate
NEXT
EDIT
DONE
EXIT
NEXT
EDIT
Aux Input 1
BACK
NEXT
SAVE
Set Meter
Counts
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Num Aux Inputs
3
EXIT
NEXT
EDIT
Aux Input 2
Counts
EXIT
NEXT
EDIT
Aux Input 3
Counts
BACK
NEXT
SAVE
Set Meter
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Pulse Timing
Pulse 500 ms
EXIT
NEXT
EDIT
Pulsed Output 1
Volume Total
Select Type
EXIT
NEXT
EDIT
Pulsed Output 2
Volume Total
Select Type
EXIT
NEXT
EDIT
Pulsed Output 3
Alarm
Select Type
EXIT
NEXT
EDIT
Pulse 1 Scaling
x1
Select Multiplier
EXIT
NEXT
EDIT
Pulse 2 Scaling
x1
Select Multiplier
EXIT
NEXT
EDIT
Pulse 3 Scaling
x1
Select Multiplier
EXIT
NEXT
EDIT
Aux Input 1
Counts
EXIT
NEXT
EDIT
Num Aux Inputs
2
EXIT
NEXT
EDIT
Aux Input 2
Counts
EXIT
NEXT
EDIT
Pulse Timing
Pulse 500 ms
EXIT
NEXT
EDIT
Pulsed Output 1
Volume Total
Select Type
EXIT
NEXT
EDIT
Pulse 1 Scaling
x1
Select Multiplier
BACK
NEXT
SAVE
Set Meter
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Aux Input 1
Counts
EXIT
NEXT
EDIT
Num Aux Inputs
1
EXIT
NEXT
EDIT
Pulsed Output 1
Volume Total
Select Type
EXIT
NEXT
EDIT
Pulsed Output 2
Volume Total
Select Type
EXIT
NEXT
EDIT
Pulse Timing
Pulse 500 ms
EXIT
NEXT
EDIT
Pulse 1 Scaling
x1
Select Multiplier
EXIT
NEXT
EDIT
Pulse 2 Scaling
x1
Select Multiplier
BACK
NEXT
SAVE
Set Meter
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Aux Input 1
Counts
EXIT
NEXT
EDIT
Num Aux Inputs
2
EXIT
NEXT
EDIT
Aux Input 2
Counts
BACK
NEXT
SAVE
Set Meter
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Analog Signal
4-20 mA
EXIT
NEXT
EDIT
Analog Output
Volume Rate
EXIT
NEXT
EDIT
Analog Output Max
500.000
Analog Output Units
Select Signal
Select Type
EXIT
NEXT
EDIT
Analog Output Min
000.000
Analog Output Units
EXIT
NEXT
EDIT
Pulsed Output 1
Energy Total
Select Type
EXIT
NEXT
EDIT
Pulsed Output 2
Volume Total
Select Type
EXIT
NEXT
EDIT
Pulse Timing
Pulse 500 ms
EXIT
NEXT
EDIT
Pulse 1 Scaling
x1
Select Multiplier
EXIT
NEXT
EDIT
Pulse 2 Scaling
x1
Select Multiplier
BACK
NEXT
SAVE
Set Meter
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Analog Signal
4-20 mA
EXIT
NEXT
EDIT
Analog Output
Volume Rate
EXIT
NEXT
EDIT
Analog Output Max
500.000
Analog Output Units
Select Signal
Select Type
EXIT
NEXT
EDIT
Analog Output Min
000.000
Analog Output Units
EXIT
NEXT
EDIT
Aux Input 1
Counts
EXIT
NEXT
EDIT
Num Aux Inputs
1
EXIT
NEXT
EDIT
Pulsed Output 1
Energy Total
Select Type
EXIT
NEXT
EDIT
Pulse Timing
Pulse 500 ms
EXIT
NEXT
EDIT
Pulse 1 Scaling
x1
Select Multiplier
BACK
NEXT
SAVE
Set Meter
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Analog Signal
4-20 mA
EXIT
NEXT
EDIT
Analog Output
Volume Rate
EXIT
NEXT
EDIT
Analog Output Max
500.000
Analog Output Units
Select Signal
Select Type
EXIT
NEXT
EDIT
Analog Output Min
000.000
Analog Output Units
NEXT
None
Instance Number
NEXT
EDIT
NEXT
NEXT
F
Set Meter
NEXT
gpm
NEXT
38400
SAVE
Medium
NEXT
NEXT
HH:MM:SS
0 - 255
EXIT
EXIT
EXIT
EDIT
EXIT
Odd Even None
57017
EDIT
DONE
NEXT
NEXT
Modbus Address
EDIT
EDIT
Short Commissioning
Next to complete Install
or adjust settings.
EDIT
gallons
EDIT
Parity
Set Meter
EDIT
EDIT
NEXT edits units of
measure
SAVE completes install
with current settings
NEXT
EXIT
Protocol
NEXT
DONE
0 - 4194303
Temperature
017
Set Date
Volume
Select Units
Short Commissioning
Protocol
Select Units
NEXT
EDIT
EDIT
Baud Rate
1
BACnet Address
EDIT
BACK
NEXT
DONE
EDIT
Set Time
Flow
Modbus
EDIT
EXIT
NEXT
DONE
0 - 247
Water
Select Units
Units of Measure & Aux I/O
Configuration Settings
Stop Bits
NEXT
EXIT
EXIT
BACnet
EXIT
EXIT
9600
YYYY:MM:DD
1 2
1
DONE
Baud Rate
NEXT
EDIT
DONE
EXIT
NEXT
EDIT
Aux Input 1
BACK
NEXT
SAVE
Set Meter
Counts
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Num Aux Inputs
3
EXIT
NEXT
EDIT
Aux Input 2
Counts
EXIT
NEXT
EDIT
Aux Input 3
Counts
BACK
NEXT
SAVE
Set Meter
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Pulse Timing
Pulse 500 ms
EXIT
NEXT
EDIT
Pulsed Output 1
Volume Total
Select Type
EXIT
NEXT
EDIT
Pulsed Output 2
Volume Total
Select Type
EXIT
NEXT
EDIT
Pulsed Output 3
Alarm
Select Type
EXIT
NEXT
EDIT
Pulse 1 Scaling
x1
Select Multiplier
EXIT
NEXT
EDIT
Pulse 2 Scaling
x1
Select Multiplier
EXIT
NEXT
EDIT
Pulse 3 Scaling
x1
Select Multiplier
EXIT
NEXT
EDIT
Aux Input 1
Counts
EXIT
NEXT
EDIT
Num Aux Inputs
2
EXIT
NEXT
EDIT
Aux Input 2
Counts
EXIT
NEXT
EDIT
Pulse Timing
Pulse 500 ms
EXIT
NEXT
EDIT
Pulsed Output 1
Volume Total
Select Type
EXIT
NEXT
EDIT
Pulse 1 Scaling
x1
Select Multiplier
BACK
NEXT
SAVE
Set Meter
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Aux Input 1
Counts
EXIT
NEXT
EDIT
Num Aux Inputs
1
EXIT
NEXT
EDIT
Pulsed Output 1
Volume Total
Select Type
EXIT
NEXT
EDIT
Pulsed Output 2
Volume Total
Select Type
EXIT
NEXT
EDIT
Pulse Timing
Pulse 500 ms
EXIT
NEXT
EDIT
Pulse 1 Scaling
x1
Select Multiplier
EXIT
NEXT
EDIT
Pulse 2 Scaling
x1
Select Multiplier
BACK
NEXT
SAVE
Set Meter
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Aux Input 1
Counts
EXIT
NEXT
EDIT
Num Aux Inputs
2
EXIT
NEXT
EDIT
Aux Input 2
Counts
BACK
NEXT
SAVE
Set Meter
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Analog Signal
4-20 mA
EXIT
NEXT
EDIT
Analog Output
Volume Rate
EXIT
NEXT
EDIT
Analog Output Max
500.000
Analog Output Units
Select Signal
Select Type
EXIT
NEXT
EDIT
Analog Output Min
000.000
Analog Output Units
EXIT
NEXT
EDIT
Pulsed Output 1
Energy Total
Select Type
EXIT
NEXT
EDIT
Pulsed Output 2
Volume Total
Select Type
EXIT
NEXT
EDIT
Pulse Timing
Pulse 500 ms
EXIT
NEXT
EDIT
Pulse 1 Scaling
x1
Select Multiplier
EXIT
NEXT
EDIT
Pulse 2 Scaling
x1
Select Multiplier
BACK
NEXT
SAVE
Set Meter
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Analog Signal
4-20 mA
EXIT
NEXT
EDIT
Analog Output
Volume Rate
EXIT
NEXT
EDIT
Analog Output Max
500.000
Analog Output Units
Select Signal
Select Type
EXIT
NEXT
EDIT
Analog Output Min
000.000
Analog Output Units
EXIT
NEXT
EDIT
Aux Input 1
Counts
EXIT
NEXT
EDIT
Num Aux Inputs
1
EXIT
NEXT
EDIT
Pulsed Output 1
Energy Total
Select Type
EXIT
NEXT
EDIT
Pulse Timing
Pulse 500 ms
EXIT
NEXT
EDIT
Pulse 1 Scaling
x1
Select Multiplier
BACK
NEXT
SAVE
Set Meter
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Analog Signal
4-20 mA
EXIT
NEXT
EDIT
Analog Output
Volume Rate
EXIT
NEXT
EDIT
Analog Output Max
500.000
Analog Output Units
Select Signal
Select Type
EXIT
NEXT
EDIT
Analog Output Min
000.000
Analog Output Units
NEXT
None
Instance Number
NEXT
EDIT
NEXT
NEXT
F
Set Meter
NEXT
gpm
NEXT
38400
SAVE
Medium
NEXT
NEXT
HH:MM:SS
0 - 255
EXIT
EXIT
EXIT
EDIT
EXIT
Odd Even None
57017
EDIT
DONE
NEXT
NEXT
Modbus Address
EDIT
EDIT
Short Commissioning
Next to complete Install
or adjust settings.
EDIT
gallons
EDIT
Parity
Set Meter
EDIT
EDIT
NEXT edits units of
measure
SAVE completes install
with current settings
NEXT
EXIT
Protocol
NEXT
DONE
0 - 4194303
Temperature
017
Set Date
Volume
Select Units
Short Commissioning
Protocol
Select Units
NEXT
EDIT
EDIT
Baud Rate
1
BACnet Address
EDIT
BACK
NEXT
DONE
EDIT
Set Time
Flow
Modbus
EDIT
EXIT
NEXT
DONE
0 - 247
Water
Select Units
Units of Measure & Aux I/O
Configuration Settings
Stop Bits
NEXT
EXIT
EXIT
BACnet
EXIT
EXIT
9600
YYYY:MM:DD
1 2
1
DONE
Baud Rate
NEXT
EDIT
DONE
EXIT
NEXT
EDIT
Aux Input 1
BACK
NEXT
SAVE
Set Meter
Counts
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Num Aux Inputs
3
EXIT
NEXT
EDIT
Aux Input 2
Counts
EXIT
NEXT
EDIT
Aux Input 3
Counts
BACK
NEXT
SAVE
Set Meter
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Pulse Timing
Pulse 500 ms
EXIT
NEXT
EDIT
Pulsed Output 1
Volume Total
Select Type
EXIT
NEXT
EDIT
Pulsed Output 2
Volume Total
Select Type
EXIT
NEXT
EDIT
Pulsed Output 3
Alarm
Select Type
EXIT
NEXT
EDIT
Pulse 1 Scaling
x1
Select Multiplier
EXIT
NEXT
EDIT
Pulse 2 Scaling
x1
Select Multiplier
EXIT
NEXT
EDIT
Pulse 3 Scaling
x1
Select Multiplier
EXIT
NEXT
EDIT
Aux Input 1
Counts
EXIT
NEXT
EDIT
Num Aux Inputs
2
EXIT
NEXT
EDIT
Aux Input 2
Counts
EXIT
NEXT
EDIT
Pulse Timing
Pulse 500 ms
EXIT
NEXT
EDIT
Pulsed Output 1
Volume Total
Select Type
EXIT
NEXT
EDIT
Pulse 1 Scaling
x1
Select Multiplier
BACK
NEXT
SAVE
Set Meter
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Aux Input 1
Counts
EXIT
NEXT
EDIT
Num Aux Inputs
1
EXIT
NEXT
EDIT
Pulsed Output 1
Volume Total
Select Type
EXIT
NEXT
EDIT
Pulsed Output 2
Volume Total
Select Type
EXIT
NEXT
EDIT
Pulse Timing
Pulse 500 ms
EXIT
NEXT
EDIT
Pulse 1 Scaling
x1
Select Multiplier
EXIT
NEXT
EDIT
Pulse 2 Scaling
x1
Select Multiplier
BACK
NEXT
SAVE
Set Meter
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Aux Input 1
Counts
EXIT
NEXT
EDIT
Num Aux Inputs
2
EXIT
NEXT
EDIT
Aux Input 2
Counts
BACK
NEXT
SAVE
Set Meter
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Analog Signal
4-20 mA
EXIT
NEXT
EDIT
Analog Output
Volume Rate
EXIT
NEXT
EDIT
Analog Output Max
500.000
Analog Output Units
Select Signal
Select Type
EXIT
NEXT
EDIT
Analog Output Min
000.000
Analog Output Units
EXIT
NEXT
EDIT
Pulsed Output 1
Energy Total
Select Type
EXIT
NEXT
EDIT
Pulsed Output 2
Volume Total
Select Type
EXIT
NEXT
EDIT
Pulse Timing
Pulse 500 ms
EXIT
NEXT
EDIT
Pulse 1 Scaling
x1
Select Multiplier
EXIT
NEXT
EDIT
Pulse 2 Scaling
x1
Select Multiplier
BACK
NEXT
SAVE
Set Meter
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Analog Signal
4-20 mA
EXIT
NEXT
EDIT
Analog Output
Volume Rate
EXIT
NEXT
EDIT
Analog Output Max
500.000
Analog Output Units
Select Signal
Select Type
EXIT
NEXT
EDIT
Analog Output Min
000.000
Analog Output Units
EXIT
NEXT
EDIT
Aux Input 1
Counts
EXIT
NEXT
EDIT
Num Aux Inputs
1
EXIT
NEXT
EDIT
Pulsed Output 1
Energy Total
Select Type
EXIT
NEXT
EDIT
Pulse Timing
Pulse 500 ms
EXIT
NEXT
EDIT
Pulse 1 Scaling
x1
Select Multiplier
BACK
NEXT
SAVE
Set Meter
NEXT edits units of
measure
SAVE completes install
with current settings
EXIT
NEXT
EDIT
Analog Signal
4-20 mA
EXIT
NEXT
EDIT
Analog Output
Volume Rate
EXIT
NEXT
EDIT
Analog Output Max
500.000
Analog Output Units
Select Signal
Select Type
EXIT
NEXT
EDIT
Analog Output Min
000.000
Analog Output Units
NEXT
None
Instance Number
NEXT
EDIT
NEXT
NEXT
F
Set Meter
NEXT
gpm
NEXT
38400
SAVE
Medium
NEXT
NEXT
HH:MM:SS
0 - 255
EXIT
EXIT
EXIT
EDIT
EXIT
Odd Even None
57017
EDIT
DONE
NEXT
NEXT
Modbus Address
EDIT
EDIT
Short Commissioning
Next to complete Install
or adjust settings.
EDIT
gallons
EDIT
Parity
Set Meter
EDIT
EDIT
NEXT edits units of
measure
SAVE completes install
with current settings
NEXT
EXIT
Protocol
NEXT
DONE
0 - 4194303
Temperature
017
Set Date
Volume
Select Units
Short Commissioning
Protocol
Select Units
NEXT
EDIT
EDIT
Baud Rate
1
BACnet Address
EDIT
BACK
NEXT
DONE
EDIT
Set Time
Flow
Modbus
EDIT
EXIT
NEXT
DONE
0 - 247
Water
Select Units
Units of Measure & Aux I/O
Configuration Settings
Stop Bits
NEXT
EXIT
EXIT
BACnet
EXIT
EXIT
9600
YYYY:MM:DD
1 2
1
DONE
Baud Rate
NEXT
EDIT
DONE
F = 3 F = 4 F = 5 F = 6
(Continued from Page 18) (Continued from Page 18) (Continued from Page 18) (Continued from Page 18)