OpenEye CM-206 RevB User manual

Please carefully read these instructions before using this product.
Save this document for future use.
30657AB
model no: CM-206 Rev B
High Resolution Indoor
Dome Camera
Camera Installation & Conguration
Regulatory Compliance
General Specications Camera Overview Camera OSD Menu
Hardware Kit Contents
Camera Adjustments
Adjusting the Camera
Emissions FCC part 15 Class B
CE: EN55011
ICES-003
EN55022
CISPR 11
CISPR22
ANSI C63.4
Immunity CE: EN50130-4
FCC COMPLIANCE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in as
residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try \to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced Radio/TV technician for help.
CISPR 22 WARNING:
This is a Class B product. In a domestic environment this product may cause radio interference in which case the
user may be required to take adequate measures.
POWER SUPPLY REQUIREMENTS:
For use with listed Audio/Video product and only connected to 15W or less power supply.
*Power supply should be a NEC Class 2 / LPS Supply.
EQUIPMENT MODIFICATION CAUTION:
Equipment changes or modications not expressly approved by the manufacturer, the party responsible for FCC
compliance, could void the user’s authority to operate the equipment and could create a hazardous condition.
This class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
• Wall anchors (x3)
• D5 screws (x3)
• T6 screw (x1)
• ¾” cable entry sealing plug
• Torx Driver
• Quick Install Adapter
• Wire-Ended Power Adapter Lead
The following illustrates the Service Board. You can make adjustments to your camera
using the keys on the control bank, or by using the optional external OSD control board.
With the exception of the Focus (A) and Field of View (B) controls on the camera, all
settings are made using the keys on the OSD Service Board. When making adjust-
ments using the OSD Service Board, the camera must have power and be connected
to a video display.
1. Press and hold the MENU key for three seconds to access the top level menu.
2. Use the arrow keys on the service board to navigate the OSD menu and use the
MENU key to conrm your selections.
3. When you have completed the camera conguration, you must select EXIT to
save your changes.
4. If necessary, you can reset the camera to the factory default settings by selecting
CAMERA RESET in the OSD menu.
Dead Pixel Compensation: The CM-206 camera has a feature that can cover most
dead pixels that could occur over time. To enable this feature:
1. Select DPC under the SPECIAL menu.
2. Cover the lens with your hand to black out the image and press the MENU key.
3. When the DPC feature is enabled, the camera will return to the menu. It may take
up to 30 seconds.
A: Focus Adjuster
B: Field of View Adjuster
C: External OSD Control
Board Connector
D: Service Monitor Jack
Model No. CM-206RevB
Image Sensor 1/3” Sony CCD
Imaging DSP Sony Efo-E 2
IP Rating IP55
Type / Format NTSC
Wide Dynamic Range Yes, Digital WDR
Minimum Illumination 0.3 Lux @ 50 IRE, 0.15 Lux @ 30 IRE
Day / Night Digital Day / Night
Resolution 700 TVL
Service Monitor Jack Yes
S/N Ratio >50dB
Focal Length 3.3 ~ 12 mm
Iris Control Auto Iris
Synchronization Internal
Video Output 1.0Vpp 75Ω BNC Unbalanced
White Balance AWB, ATW, ATW2, AWC, MWB, Indoor, Outdoor
Auto White Balance Range 2700K ~ 9700K (AWB/ATW), 2500K ~ 20,000K (AWT2)
Backlight Compensation Full Range
Auto Gain Control 44.8 dB
Operating Temperature 14˚ ~ 122˚ F (-10˚ ~ 50˚C)
Heater No
Power Consumption 2.5W Max
Rated Amperage 0.2A (12vDC) / 0.1A (24vAC)
Imput Voltage 12vDC / 24vAC (± 10%)
Weight 0.6 lbs (0.27 kg)
Dimensions ø4.7” (120 mm) x H: 3.9” (94.2 mm)
Housing / Dome Cover White / Clear
Lens Manual Auto Iris Type DC / Video
Auto Mode Open / Close / Auto
Speed 0 ~ 255
Shutter / AGC Manual Manual
Setup
Mode Shut + AGC
Shutter 1/50 (1/60*), 1/100 (1/120*), 1/250
1/500, 1/1000, 1/2000, 1/4000,
1/10000
AGC 6.00, 12.00, 18.00, 24.00, 30.00,
36.00, 42.00, 44.80
Auto Auto Setup Mode Shut + Auto Iris / Auto Iris
High
Luminance
Brightness 0 ~ 255
Low
Luminance
Mode Off / AGC
Brightness X0,25 / X0.5 / X0.75 / X1.0
White Bal. ATW ATW Speed 0 ~ 255
Delay Cnt 0~ 255
ATW Frame X0.5 / X1.0 / X1.5 / X2/0
Environment Indoor / Outdoor
Push B-Gain 0 ~ 255
User 1/2 User 1/2
WB
R-Gain 0 ~ 255
Anti CR
Manual Manual WB Level 0 ~ 255
Push Lock
Backlight Off / BLC / HLC Mirror Off / On
Pict Adjust Pict Adjust Brightness 0 ~ 255
Contrast 0 ~ 255
Sharpness 0 ~ 255
Hue 0 ~ 255
Gain 0 ~ 255
ATR Off Luminance Low / Md / High
On ATR Contrast Low / Mdlow / Md / Mdhigh / High
Motion Det On Motion Det Detect Sense 0 ~ 127
Off Block Disp Off / On / Enable
Monitor Area Off / On
Area Sel 1/4 ~ 4/4
Top 0 ~ 244
Bottom 0 ~ 244
Left 0 ~ 474
Right 0 ~ 474
Privacy On Privacy Area Sel 1/4 ~ 4/4 (1/8 ~ 8/8**)
Off To p 0 ~ 244
Bottom 0 ~ 244
Left 0 ~ 474
Right 0 ~ 474
Color 1 ~ 8
Transp 0.00 / 0.50 / 0.75 / 1.00
Mosaic Off / On
Day / Night Auto Day / Night Burst Off / On
Delay Cnt 0 ~ 255
Day - Night 0 ~ 255
Night - Day 0 ~ 255
Color
B/W B/W Burst Off / On
IR Optimizer Off / On
Mode Auto / Center
Level 0 ~ 31
NR NR NR Mode Off / Y / C / Y/C
Y Level 0 ~ 15
Camera ID Off / On C Level 0 ~ 15
Sync Int
Language English / Chinese / Spanish / Portuguese / Russian / French / German / Japanese
Camera Reset
Exit
Next
Back
Save All
23221 E Knox Ave
Liberty Lake, WA 99019
1.888.542.1103
www.openeye.net
A
B
DC
OSD menu
control bank
Menu / Enter
Down
Up
Left
Right
Service Jack
Control Board
Connector

Installation
Template
Installation Instructions
Precautions
• Do not attempt to dismantle the camera module mounted within the dome. There
are no user serviceable parts in the camera module. Refer servicing to a qualied
professional.
• Handle the camera with care. Do not abuse the camera. Avoid striking or shaking
it. Improper handling and storage could damage the camera.
• Do not operate the camera beyond its temperature or power source rating. Refer to
the environmental information provided in this document.
Emissions
• FCC COMPLIANCE: This equipment complies with Part 15 of the FCC rules for
intentional radiators and Class B digital devices when installed and used in ac-
cordance with the instruction manual. Following these rules provides reasonable
protection against harmful interference from equipment operated in a commercial
area. This equipment should not be installed in a residential area as it can radiate
radio frequency energy that could interfere with radio communications, a situation
the user would have to x at their own expense.
Surface mount (in wall or ceiling)
Using Quick Install Adapter
• Cut a 1.3” (35mm) hole in the mounting surface as indicated
on the template (T5).
Using Screws
• Drill three 1/4” (7.5mm) holes as indicated on the template
(D5) and insert a wall anchor in each hole. Use the supplied
D5 screws to attach the camera.
Cable Access
• The cables are threaded through the base knockout (shown in
C1). It is threaded for use with the quick install adapter.
• When mounting the dome on a surface using the three D5
screws, use one of the side knockouts as indicated by C3 for
cable entry. See the Installation Instructions for instructions on
opening the required knock-out panel.
1. Remove the dome cover and the camera liner
Gently turn the dome cover counter-clockwise to unlock and pull free of the dome
base. Remove the camera liner by gently pulling it free of the two notches (D4) in
the camera base (see g. D).
2. Use the template to mark out and prepare the mounting area
When mounting the dome to a ceiling or wall using screws, rst knock out the
screw access holes (C2) that correspond to the template marks “D5”. This can be
done by using a Phillips screwdriver. When mounting the dome to a ceiling using
the quick install adapter, use the template to cut a hole as the circle marked “T5”
with a hole cutter.
3. Open the required knock-out panel
Use a sharp knife or side cutter pliers to cut one of the side knock-outs (C3) to the
size required to allow cable entry. Be careful not to hurt yourself or damage the
camera when using knives and side cutter pliers.
B1 B1
C1: Threaded base
C2: Screw access holes
C3: Cable knock-outs
F1: Camera liner
F2: Dome cover
D1: Dome base
D2: Camera liner
D3: Dome cover
D4: Notches (on both sides)
G1: Video output connector
G2: Power input connector
G3: Cable entry sealing plug (¾”)
H1: Quick install adapter
H2: Cable entry sealing plug (½”)
Push the camera
liner up to the
base until it clicks
into place.
Loosen screws, but not remove
them,to rst extend the locking
arms. Then tighten the screws
sufciently to compress the arms
to adjust to the mounting surface;
however, DO NOT OVERTIGHTEN.
Mount with screws
Use Quick Mount Adapter
C3
C3
C3
C2
C1
C2
C2
T6 screw
G2
G1
G3
H1
H2
D5
D5
D5
T5
D1
D2
D4
D5
Rotate and pan
the camera base
to the desired
position.
DO NOT rotate/tilt the disk beyond
its maximum allowed range (350/80
degrees) or damage may occur.
Make sure the wires are arranged
in a direction that allows you to
rotate/pan the disk smoothly.
F1
F2
4. Mount the dome enclosure
Using one of the mounting schemes discussed
on this sheet (either using screws or the quick
mount adapter), x the dome enclosure in place.
5. Connect the wiring
Feed the pre-connected main lead (that feeds to the connections G1 and G2)
through the appropriate point and connect it to your video out and power in cables.
The service monitor jack is provided for temporary video connection when focusing
the camera.
6. Adjust the camera position
You can adjust the focusing position by rotating and panning the camera base (see
g. E).
7. Install the camera liner
Carefully t the camera liner (F1) over the camera base so that it snaps into place
as shown in g. F and does not obstruct the camera lens.
8. Complete installation
Insert the 3/4” cable entry sealing plug (G3) in the dome base, then push the
cables (G1 and G2) through the dome base and the 3/4” cable entry sealing plug
(G3). Make sure the plug is properly installed in the camera base. Replace the
dome cover (F2) and rotate to close it as shown in g. F. Use the supplied T6
screw to secure the cover and prevent tampering (see g. G).
9. Complete installation (quick install adapter)
Insert the 1/2” cable entry sealing plug (H3) in the quick install adapter (H1) and
insert the adapter the hole cut using the provided template as a guide. Use the
screws on the adapter to adjust the position of the two locking arms (B1) on the
quick install adapter and adjust to the mounting surface. Push the cables through
the opening (H1) and 1/2” cable entry sealing plug (H2). Make sure the plug is
properly installed in the camera base. Thread the dome onto the quick install
adapter. This takes about 1 1/2 turns. DO NOT OVERTIGHTEN.
Service jack
socket