OpenEye CM-512 User manual

This quick operation guide is a quick reference for users to install and operate the dome
camera and only provides basic information on the camera’s settings and operation. Before
attempting to connect, congure and operate the dome camera, please read the installation
guide and the user manual thoroughly.
Box Contents
Dome Switch Denition
1Alarm Inputs
2BNC Output
3Console Connector
(Reserved)
4Communication Switch
5Camera ID Setting
6RS-485 Connector
7Protocol Settings
8Power Connector
Communication Switch Setting
The table below shows the function of each switch within the Communication Switch on the
dome back plate.
Dome Control Protocol Setting
Refer to the table below and select a protocol and baud rate appropriate for your installation,
based on the control device. Adjust the Protocol Switch on the dome camera back plate. For
example, the protocol switch should be set as shown if you are using the Pelco D protocol,
with the switch number of 01 and a baud rate of 2400. For more switch congurtion details,
refer to the user manual
RS-485 Connector
The dome camera uses the RS-485 interface to communicate with a connected control device.
Connect a control keyboard to the speed dome using the terminal block. OpenEye recom-
mends using CAT 5 cables for RS-485 communication with a maximum length of 4000 feet
(1219 meters) for 24-gauge wire. If the total cable length exceeds 4000 feet, use a repeater to
maintain the signals. Refer to the table below for pin denition and wiring.
Pin Denition
1R-
2GND
3R+
4T-
5T+
Power Connector
Refer to the this diagram for power connector denition before wiring.
Apply Alarm I/O
The CM-512 supports 4 digital alarm inputs and 2 digital alarm outputs. Please make sure
the alarm connections are properly wired before starting to congure alarm-related settings.
Please refer to this pin denition table for alarm system wiring.
Power Wire Length Specications
CM-512 | High Speed Dome Camera Quick Guide
www.openeye.net
Wire Gauge Maximum Distance
22 27 feet
20 44 feet
18 69 feet
16 110 feet
Wire Gauge Maximum Distance
14 175 feet
12 279 feet
10 444 feet
RS-485 Setting
Half-duplex Full-duplex
Communication Switch SW 1 RS-485 Setting
SW 2
SW 3 Termination
SW 4 Line Lock
SW 5 System Initialization
SW 6 Reserved
1AC IN +
2Frame GND
3AC IN -
Pin Denition Pin Denition
1 Alarm Out NO1 7 Alarm Out COM 2
2 Alarm Out NC 1 8 GND
3 Alarm Out COM 1 9 Alarm In 4
4 GND 10 Alarm In 3
5 Alarm Out NO 2 11 Alarm In 2
6 Alarm Out NC 2 12 Alarm In 2
Camera ID Setting
Change the camera ID if there is more than one camera on the same installation. The camera
ID is set using the camera ID switch on the back plate of the camera. For switch conguration
details, please refer to the user manual.
Note: No two cameras should have the same
camera ID, or a communication conict
may occur.
Optical Cover
CM-816 Camera Screws
Quick Start Guide User Manual Waterproof Gasket
Installation Manual Lubricant
Protocol Baud
Rate
Setting
Switch Setting
1 2 3 4 5 6
VCL 9600 OFF OFF OFF OFF OFF OFF
Pelco-D 2400 ON OFF OFF OFF OFF OFF
Pelco-P 4800 OFF ON OFF OFF OFF OFF
Chiper 9600 OFF OFF ON OFF OFF OFF
Philips 9600 ON OFF ON OFF OFF OFF
OPTIX-3 9600 ON ON ON OFF OFF OFF
AD422 4800 OFF OFF OFF ON OFF OFF
DP-P 9600 ON OFF OFF ON OFF OFF
Pelco-D 4800 ON ON OFF ON OFF OFF
Pelco-D 9600 OFF OFF ON ON OFF OFF
Pelco-P 2400 ON OFF ON ON OFF OFF
Pelco-P 9600 OFF ON ON ON OFF OFF
JVC 9600 ON ON ON ON OFF OFF
Kalatel-485 9600 ON OFF ON OFF ON OFF
Kalatel-422 4800 OFF ON ON OFF ON OFF

Item Layer 1 Layer 2 Layer 3 Default
LANGUAGE
<ENGLISH>, <JAPANESE>, <PORTUGUESE>, <SPANISH>, <FRENCH>,
<GERMAN>, <ITALIAN>, <POLISH>, <RUSSIAN>, <TRADITIONAL
CHINESE>,<SIMPLIFIED CHINESE>, <TURKISH>
ENGLISH
DEFAULT CAMERA <ON>, <OFF> ON
BACKLIGHT
<ON>
OFF
<OFF>
FOCUS AUTO
AF MODE <NORMAL>, <Z. TRIG.>,
<PT TRIG.> NORMAL
EXIT + SAVE
MANUAL
AE MODE
EXPOSURE COMP.
<OFF>, EXPOSURE VALUE: <-10.5dB> ~
<10.5dB> OFF
EXIT + SAVE: YES
AE MODE
AUTO
BRIGHT VALUE; SHUTTER
SPEED; IRIS VALUE; GAIN
VALUE: AUTO
AUTO
EXIT + SAVE: YES
SHUTTER
SHUTTER SPEED: <1/60>
~ <1/10000> SEC.
EXIT + SAVE: YES
IRIS
IRIS VALUE
<F1.6> ~ <F28>
EXIT + SAVE: YES
MANUAL
BRIGHT VALUE: AUTO
SHUTTER SPEED: <1/60>
~ <1/10000> SEC.
GAIN VALUE <-3> dB ~
<28>dB
EXIT + SAVE: YES
EXIT + SAVE YES
WBC MODE
AUTO (Auto White Balance)
AUTO
INDOOR
OUTDOOR
ATW (Auto-tracing WBC)
MANUAL
R GAIN <000> ~ <127>
B GAIN <000> ~ <127>
EXIT + SAVE: YES
IMAGE CTRL
MAX DIGITAL ZOOM <OFF>, <2x> ~ <12x> OFF
SLOW SHUTTER <ON>, <OFF> OFF
D.N.R.
2 D.N.R. <ON>, <OFF>
3 D.N.R. <ON>, <OFF>
EXIT + SAVE: YES
IMAGE INVERSE <ON>, <OFF> OFF
FREEZE <ON>, <OFF> OFF
APERTURE <01> ~ <16> 7
STABILIZER <ON>, <OFF>
EXIT YES
TELEMETRY CTRL
FLIP <OFF>, <M.E.>, <IMAGE> OFF
ANGLE ADJUSTER
MIN ANGLE <-10 ~ +10 DEG> 0
MAX ANGLE <080 ~ 100 DEG> 90
SPEED BY ZOOM <ON>, <OFF> OFF
AUTO CALIBRATE <ON>, <OFF> OFF
PASSWORD <ON>, <OFF> OFF
OSD AUTO CLOSE <OFF>, <10> ~ <30> SEC.
SYSTEM RESET
SYSTEM RESET <YES>
DEFAULT SYSTEM <YES>
EXIT <YES>
EXIT YES
ID DISPLAY <ON>, <OFF> ON
TITLE DISPLAY <ON>, <OFF> OFF
TITLE SETTING <1> ~ <9>, <A> ~ <Z>, <:>, </>, <.>, <,>, <(>, <)>, <+>, <?>, <->
PRESET
PRESET SET <001>~<256> ENTER
PRESET RUN <001>~<256> ENTER
EXIT YES
TOUR
TOUR LINE <1> ~ <8> 1
TOUR POINT <01> ~ <64> 1
PRESET POS. <001> ~ <255>, <END> END
SPEED <01> ~ <15> 1
DWELL TIME <000> ~ <127> SEC. 0
RUN TOUR ENTER
EXIT YES
AUTOSCAN
AUTOSCAN LINE <1> ~ <4> 1
START POINT <PT MOVE>, <TO SAVE>
END POINT <PT MOVE>, <TO SAVE>
DIRECTION <RIGHT>, <LEFT> RIGHT
SPEED <01> ~ <04> 1
RUN AUTOSCAN ENTER
EXIT YES
Item Layer 1 Layer 2 Layer 3 Default
PATTERN
PATTERN LINE <1> ~ <8>
RECORD START ENTER
RECORD END ENTER
RUN PATTERN ENTER
EXIT YES
HOME SETTING
HOME FUNCTION <ON>, <OFF> OFF
SELECT MODE <PRESET>, <TOUR>, <AUTOSCAN>,
<PATTERN> PRESET
PRESET POINT <001> ~ <256> 1
RETURN TIME <1> ~ <128> MIN. 1
GO ENTER
EXIT YES
IR FUNCTION
<AUTO> THREADHOLD <MID>, <HI>, <LOW>
AUTO
EXIT + SAVE: YES
<MANUAL> IR MANUAL <ON>, <OFF>
EXIT + SAVE: YES
ALARM SETTING
ALARM PIN <1> ~ <8> 1
ALARM SWITCH <ON>, <OFF> OFF
ALARM TYPE <NO> (Normal Open), <NC> (Normal Close) NC
ALARM ACTION <PRESET>, <TOUR>, <AUTOSCAN>, <PAT-
TERN> PRESET
PRESET POINT <001> ~ <256> 1
TOUR LINE <1> ~ <8> 1
AUTOSCAN LINE <1> ~ <4> 1
PATTERN LINE <1> ~ <8> 1
DWELL TIME <001> ~ <127> Sec., <ALWAYS> ALWAYS
EXIT YES
ALARM DETECT NONE
WDR FUNCTION <ON>, <OFF> OFF
PRIVACY MASK
PRIVACY SWITCH <ON>, <OFF> OFF
TRANSPARENCY <ON>, <OFF> OFF
COLOR
<BLACK>, <WHITE>,<RED>, <GREEN>,
<BLUE>, <CYAN>, <YELLOW>, <MAGENTA>,
<MOSAIC 1>, <MOSAIC 2>, <MOSAIC 3>
BLACK
SET MASK <01> ~ <20>
H CENTER: L/R
V CENTER: D/U
H SIZE <000> ~ <080>
V SIZE <000> ~ <060>
EXIT + SAVE
CLEAR MASK <01> ~ <20>
EXIT YES
TIME SETTING
TIME DISPLAY <ON>, <OFF> OFF
SET YEAR <00> ~ <99>
SET MONTH <01> ~ <12>
SET DAY <00> ~ <31>
SET HOUR <00> ~ <23>
SET MINUTE <00> ~ <59>
EXIT+SAVE
SCHEDULE
SWITCH <ON>, <OFF> OFF
POINT <01> ~ <32> 1
HOUR <00> ~ <23> 0
MINUTE <00> ~ <59> 0
MODE
NONE NO FUNCTION NONE
PRESET PRESET POINT
<001> ~ <256>
TOUR TOUR LINE
<1> ~ <8>
AUTOSCAN AUTOSCAN LINE <1> ~
<4>
PATTERN PATTERN LINE <1> ~ <8>
IR FUNCTION IR FUNCTION <AUTO>,
<ON>, <OFF>
SCHEDULE
RESET YES
EXIT YES
EXIT OSD YES
Dome OSD Menu Tree
The OSD setup menu structure of the CM-511 camera is listed below. The star symbol indicates the factory default.
31450AC
Copyright ©2013 OpenEye. All Rights Reserved. Information contained in this document is subject to
change without prior notice. OpenEye does its best to provide accurate information but cannot be held
responsible for typos or mistakes.
23221 E Knox Ave
Liberty Lake, WA 99019
1.888.542.1103