Optika Italy H Series User manual

Model
C-HP4
HDMI Cameras – H Series
INSTRUCTION MANUAL
Ver. 1.0 2021

Page 2
1. Warning 3
2. Symbols and conventions 3
3. Safety Information 3
4. Intended use 3
5. C-HP4 Basic features 4
5.1 Package content 4
5.2 Quick Instructions for C-HP4 camera 5
5.2.1 HDMI Mode 5
5.2.2 USB Mode 5
6. C-HP4 User Interface (UI) and its Functions 6
6.1 The Camera Control Panel 7
6.2 The Measurement Toolbar 8
6.3 Camera calibration 9
6.4 Icons and Functions of the Camera Control Toolbar 11
6.4.1 Setting > Measurement 11
6.4.2 Setting>Magnication 12
6.4.3 Setting > Image Format 12
6.4.4 Setting > Video 13
6.4.5 Setting > Storage 14
6.4.6 Setting > Files 14
6.4.7 Setting > Language 15
6.3.8 Setting > Miscellaneous 16
7. Micrometric Slide M-005 17
Equipment disposal 18
Table of Contents

Page 3
1. Warning
This device is a scientic precision instrument designed to last for many years with a minimum of maintenance. It is built
to high optical and mechanical standards and to withstand daily use. We remind you that this manual contains important
information on safety and maintenance, and that it must therefore be made accessible to the instrument users. We decline
any responsibility deriving from incorrect instrument use uses that does not comply with this manual.
2. Symbols and conventions
The following chart is an illustrated glossary of the symbols that are used in this manual.
CAUTION
This symbol indicates a potential risk and alerts you to proceed with caution.
ELECTRICAL SHOCK
This symbol indicates a risk of electrical shock.
3. Safety Information
Avoiding Electrical Shock
Before plugging in the power supply, make sure that the supplying voltage of your region matches with the operation voltage
of the equipment and that the lamp switch is in o󰀨 position. Users should observe all safety regulations of the region. The
equipment has acquired the CE safety label. However, users have full responsibility to use this equipment safely. Please
follow the guidelines below, and read this manual in its entirety to ensure safe operation of the unit.
4. Intended use
Standard models
For research and teaching use only. Not intended for any animal or human therapeutic or diagnostic use.
IVD Models
Also for diagnostic use, aimed at obtaining information on the physiological or pathological situation of the subject.

Page 4
5. C-HP4 Basic features
5.1 Package content
① Camera
② HDMIcable
③ USB2.0cable
④ Wirelessmouse
⑤ Micrometricslide
⑥ SDcard16GB
⑦ Powersupply
①
②
③
④
⑤
⑥
⑦
C-HP4 is a multiple interfaces (HDMI + USB2.0 + SD card) CMOS camera.
HDMI and USB2.0 are used as the data transfer interface to HDMI display or computer.
• For HDMI output, the Camera Control Panel + Measurement Toolbar and Camera Control Toolbar are overlaid on the
HDMI screen when the mouse move to the related region.
In this case, the USB mouse can be used to set the camera, browse and compare the captured image, play the video
and perform the measurement.
• For USB output, connect computer with USB connection to transfer video in real time.
From here the ProView software can control each camera function.

Page 5
① USBmouseconnector
② USB2.0connector
③ HDMIconnector
④ ON-OFFbutton
⑤ SDcardslot
⑥ Powersupplyplug
⑦ LEDindicator
5.2 Quick Instructions for C-HP4 camera
Before turning on the camera, please connect the standard C-mount camera to the camera adapter and insert it into the
microscope’s trinocular port.
①②③
④
⑤
⑥
Figure 1 - C-HP4 Rear Panel
You can use the C-HP4 camera in 2 di󰀨erent ways. Each application requires di󰀨erent hardware environment.
5.2.1 HDMI Mode
1. Plug the HDMI cable into the HDMI port ③ to connect the C-HP4 camera to HDMI display.
2. Plug the USB mouse into USB Mouse port ① to get control of the camera by using built-in software LiteView.
3. Plug 12V/1A power adapter into DC 12V slot ⑥ to supply power for the camera. The LED Indicator ⑦ will turn into red.
4. Insert SD card into SD Card slot ⑤ for saving captured images and recorded videos.
5. Press ON/OFF Button ④ to turn on the camera. The LED indicator will turn into blue.
6. Move mouse cursor to the left side of the video window, a Camera Control Panel will appear. It includes Manual/ Auto-
matic Exposure, White Balance, Sharpness and other functions, please refer to 6.1 for details.
7. Move mouse cursor to the bottom of the video window and a Camera Control Toolbar will appear. Operations like Zoom
In, Zoom Out, Flip, Freeze, Cross Line, Comparison and so on can be achieved. Please refer to 6.3 for details.
8. Move mouse cursor to the upper side of the video window, a Measurement Toolbar with calibration and other measure-
ment tools will appear, please refer to 6.2 for details. The measurement data can be output with *.CSV format.
5.2.2 USB Mode
1. Plug the USB cable provided with the camera into USB2.0 ② to connect the C-HP4 camera to the computer.
2. Plug 12V/1A power adapter into DC 12V slot ⑥ to supply power for the camera. The LED Indicator ⑦ will turn into red.
3. Press ON/OFF button ④ to turn on the camera. The LED indicator will turn into blue.
4. Start the ProView software.
5. Clicking the camera name in the camera list starts the live video.
• NOTE: When the USB cable and the mouse are plugged into the camera at the same time, the USB cable has
priority and the mouse is not available; when the USB cable is unplugged, the mouse can be used normally.
⑦

Page 6
6. C-HP4 User Interface (UI) and its Functions
The C-HP4 UI shown in Fig. 2 includes a Camera Control Panel on the left side of the video window, a Measurement Tool-
bar on the upper side of the video window, a Camera Control Toolbar on the bottom of the video window.
Figure 2 - Camera Control User Interface
1. Move the mouse cursor to the left side of the video window: the Camera Control Panel will pop up automatically.
2. Move the mouse cursor to the upper side of the video window: a Measurement Toolbar will pop up for the calibration
and measurement operations.
• When user left-clicks the Float/Fixed button on the Measurement Toolbar, the Measurement Toolbar will be xed. In
this case the Camera Control Panel will not pop up automatically even if users move mouse cursor to left side of the
video windows.
• Only when user left-clicks the button on the Measurement Toolbar to exit from measuring procedure it will be possi-
ble to perform other operations on the Camera Control Panel, or Camera Control Toolbar.
• During the measuring process, when a specic measuring object is selected an Object Location & Attributes Control Bar
will appear for changing location and properties of the selected objects.
3. Move the mouse cursor to the bottom of the video window, the Camera Control Toolbar will pop up automatically.

Page 7
6.1 The Camera Control Panel
The Camera Control Panel controls the camera to achieve the best image quality according to the specic applications.
It will pop up automatically when mouse cursor is moved to the left side of the video window (in measurement status, the
Camera Control Panel will not pop up. Only when measurement process is terminated the Camera Control Panel will pop
up by moving mouse cursor to the left side of the video window).
Left-clicking button to achieve Display/ Auto Hide switch of the Camera Control Panel.
Control Panel Function Description
Snap Capture image from the current video window
Record Record video from the current video window
Auto Exposure When Auto Exposure is checked, the system will automatically adjust ex-
posure time according to the value of exposure compensation
Exposure
Compensation Available when Auto Exposure is checked. Slide to left or right to adjust Exposure Compensation according to the current video brightness to
achieve proper brightness value
Exposure Time Available when Auto Exposure is unchecked. Slide to left or right to re-
duce or increase exposure time, adjusting brightness of the video
Gain Adjust Gain to reduce or increase brightness of video. The Noise will be
reduced or increased accordingly
Auto White
Balance White Balance adjustment according to the window video every time the button is clicked
Manual White
Balance Slide Red or Blue cursors to manually set the video White Balance
ROI White
Balance When the ROI region is moved, white Balance can be adjusted according to content inside the ROI region.
Red Slide to left or right to decrease or increase the proportion of Red in RGB
on video
Green Slide to left or right to decrease or increase the proportion of Green in
RGB on video
Blue Slide to left or right to decrease or increase the proportion of Blue in RGB
on the video
Sharpness Adjust Sharpness level of the video window
Denoise Slide left or right to denoise the image
Saturation Adjust Saturation level of the video window
Gamma Adjust Gamma level of the video. Slide to the right side to increase gam-
ma and to the left to decrease gamma
Contrast Adjust Contrast level of the video. Slide to the right side to increase con-
trast and to the left to decrease contrast
DC For DC illumination, there will be no uctuation in light source so no need
for compensating light ickering
AC(50HZ) Check AC(50HZ) to eliminate ickering “strap” caused by 50Hz illumina-
tion
AC(60HZ) Check AC(60HZ) to eliminate ickering “strap” caused by 60Hz illumina-
tion
Default Restore all the settings in the Camera Control Panel to default values

Page 8
6.2 The Measurement Toolbar
The Measurement Toolbar will pop up when moving mouse cursor to any place near the upper side of the video window.
Figure 3 - The Measurement Toolbar
Icon Function
Float/ Fix switch of the Measurement Toolbar
Dene measuring object in Show up/ Hide mode
Select the desired Measurement Unit
Select Magnication for Measurement after Calibration
Object Select
Angle
4 Points Angle
Point
Arbitrary Line
3 Points Line
Horizontal Line
Vertical Line
3 Points Vertical line
Parallel
Rectangle
Ellipse
5 Points Ellipse
Circle
3 Points Circle
Annulus
Two Circles and Center Distance
3 Points Two Circles and Center Distance
Arc
Text

Page 9
Polygon
Curve
Scale Bar
Arrow
Execute Calibration to determine the corresponding relation between magnication and resolution,
which will establish the corresponding relationship between measurement unit and the sensor pixel
size. Calibration needs to be done with the help of a micrometer. For detailed steps of carrying out
Calibration please refer to chapter 6.3.
Export the Measurement to CSV le(*.csv)
Measurement Setup
Delete All the Measurement Objects
Exit from Measurement mode
When the measurement ends, left-click on a single measuring object and the Object Location & Prop-
erties Control Bar will show up. User could move the object by dragging the object with the mouse.
But more accurate movement could be done with the control bar. The icons on the control bar mean
Move Left, Move Right, Move Up, Move Down, Color Adjustment and Delete.
Note:
1. When user left-clicks Display/Hide button on the Measurement Toolbar, it will be xed. In this case the Camera
Control Panel will not pop up automatically even if moving the mouse cursor to the left edge of the video window. Only
when user left-click the button on the Measurement Toolbar to exit from the measurement mode it will be possible to
perform other operations on the Camera Control Panel or on the Camera Control Toolbar.
2. When a specic item is selected during the measurement process, the Object Location & Attributes Control Bar
will appear for changing the object location and properties of the selected objects.
6.3 Camera calibration
The camera must be calibrated before any measurements can be taken.
To do this it is necessary to use the micrometer slide supplied with the camera.
Detailed procedure is the following:
1. Insert the objective with the lowest magnication available and put the stage micrometer on the stage.
2. Click on the “Calibrate” button in the Measurement toolbar.
3. The following dialog box appears:

Page 10
4. In the Magnication eld enter the current magnication
• Some magnication values (default ones 4x, 10x, 20x, 40x and 100x) are preset in the drop-down list.
• If user must insert a di󰀨erent magnication value, double click in the Magnication eld. The following dialog box ap-
pears:
• From here user can enter any desired magnication value.
5. Focus the ruler under the microscope.
• Along with the previous dialog box a red line appears on the image. This line is the calibration line.
6. Align the two ends of the red line with the ruler scale (try to use as many notches as possible to keep the calibration
accuracy).
7. Set the desired unit (micrometer, millimeter or nanometer) in the Calibration dialog box.
8. Insert the length of the drawn line in the Actual Length eld (using the same procedure described above).
• Micrometric slide has two rulers (see chapter 11). One is 1 mm/100 (for biological microscopes) and the other is
10mm/100 (for stereomicroscopes).
• When using the ruler 1mm/100 the interval between two long lines is 100 mm, while using the ruler 10mm/100 the inter-
val between two long lines is 1000 mm.
9. If everything is ne, click OK to end the calibration. The new magnication (the number you entered in the Magnication
edit box) will be available in the Magnication drop-down list.
10. Repeat the same procedure for each magnication available in your microscope.

Page 11
6.4 Icons and Functions of the Camera Control Toolbar
Icon Function Icon Function
Zoom In the Video Window Zoom Out the Video Window
Horizontal Flip Vertical Flip
Color / Gray Video Freeze
Display Cross Line Overlay
Compare stored image with the current live
image Browse Images and Videos in the SD Card
Settings Check the LiteView Version
The Setting function is relatively more complicated than the other functions. Here are more info about it:
6.4.1 Setting > Measurement
Figure 4 - Measurement Setting Page
Global Precision Used for setting digits behind the decimal point for measurement results.
Calibration Line Width Used for dening width of the lines for calibration.
Color Used for dening color of the lines for calibration.
EndPoint Type: Used for dening shape of the endpoints of lines for calibration.
Null: Means no endpoints.
Rectangle: Means rectangle type of endpoints. It makes alignment more easily.
Point, Angle, Line, Horizontal Line, Vertical Line, Rectangle, Circle, Ellipse, Annulus, Two Circles, Polygon, Curve
Left-click the along with the Measurement command mentioned above will unfold the corresponding attribute settings to
set the individual property of the Measurement Objects.

Page 12
6.4.2 Setting>Magnication
Figure 5 - Magnication Settings Page
Name The name of the Magnication, usually the Magnication of the microscope objective is used as
the Magnication name when calibrating, such as 4X, 10X, 40X,100X, etc. Besides, other us-
er-dened information could be added into the Magnication name too, for example, microscope
model, operator name, etc.
Resolution Pixels per meter. Devices like microscopes have high resolution value.
Clear All Click the Clear All button will clear the calibrated magnications and resolutions.
Delete Click Delete to delete the selected item for specic resolution.
Up Click Move Up to move up the selected Magnication.
Down Click Move Down to move down the selected Magnication.
6.4.3 Setting > Image Format
Figure 6 - Image Format Settings Page
Image Format JPEG: The extension of JPEG le can get very high compression rate and display very rich and
vivid images by removing redundant images and color data. In other words, it can get better im-
age quality with a minimum least disk space. If measurement objects are available, the measure-
ment objects will be burned into the image and the measurement cannot be edited.
TIFF: Tag Image File Format (TIFF) is a exible bitmap format that is mainly used to store images
including photos and artistic images.
Measurement Object Burn in Mode: The measurement objects are merged into the current image. User could not edit
Save Method the measurement objects any more. This mode is not reversible.
Layered Mode: The measurement objects are saved in di󰀨erent layer with current image data in
the target le. User could edit the measurement objects in the target le with some software on
the PC. This mode is reversible.

Page 13
6.4.4 Setting > Video
Figure 7a - Video Settings Page - Playback
Figure 7b - Video Settings Page - Video Encode
Fast Forward / Reverse The time interval of the playback of video les.
Interval
Video Encode You can choose H264 or H265 encoding. H265 encoding can signicantly reduce encoding band-
width and save storage space under the same encoding quality.

Page 14
6.4.5 Setting > Storage
Figure 8 - SD Card Settings Page
Storage Device SD Card: only SD Card is supported as the storage device.
File System List the le system format of the current storage device
Format of the FAT32: The le system of SD Card is FAT32. The maximum video le size of single le is 4GB.
Storage Device exFAT: The le system of SD Card is exFAT. The maximum video le size of single le is 4GB.
NTFS: The le system of SD Card is NTFS. The maximum video le size of single le is 4GB. Use
PC to format the SD Card and switch between FAT32, exFat and NTFS.
Unknown Status: SD Card not detected or the le system is not identied.
6.4.6 Setting > Files
Figure 9 - Files Settings Page
Image File Name Auto: The image les will be saved automatically with the specied prex.
Manual: User has to specify the le name before image saving.
Video File Name Auto: The video le will be saved automatically with the specied prex.
Manual: User has to specify the Video File Name before video recording.

Page 15
6.4.7 Setting > Language
Figure 10 - Language Selection Settings Page
English Set language of the whole software into English
Simplied Chinese Set language of the whole software into Simplied Chinese
Traditional Chinese Set language of the whole software into Traditional Chinese
Korean Set language of the whole software into Korean
Thailand Set language of the whole software into Thai
French Set language of the whole software into French
German Set language of the whole software into German
Japanese Set language of the whole software into Japanese
Italian Set language of the whole software into Italian
Russian Set language of the whole software into Russian

Page 16
6.3.8 Setting > Miscellaneous
Figure 11 - Miscellaneous Settings Page
Ruler Select to display or hide the Ruler in the video window.
Measurement Select to display the Measurement toolbar in the video window, otherwise, the Measurement
toolbar will not be displayed.
Overlay Select to support saving graphics Overlay information in fusion mode, or not to save graphics
Overlay information in fusion mode.
Auto Exposure The maximum exposure time during auto exposure process could be specied. Setting this item
to a lower value could guarantee a faster frame rate during Auto Exposure.
ROI Color Choose the ROI rectangle line color.
Camera Parameters Import the Camera Parameters from the SD card to use the previously exported parameters.
Import
Camera Parameters Export the Camera Parameters to the SD card to use the previously imported parameters.
Export
Reset to factory Restore camera parameters to its factory status.
defaults

Page 17
For biological microscopes calibration
1 DIV=0.01mm
For stereomicroscopes calibration
1 DIV=0.1mm
0 1 2 3 4 5 6 7 8 9 10
7. Micrometric Slide M-005
Micrometric slide, 26x76mm, with 2 scales
(1mm/100div. for biological microscopes / 10mm/100div. for stereomicroscopes)

Page 18
Art.13 Dlsg 25 July 2005 N°151. “According to directives 2002/95/EC, 2002/96/EC and 2003/108/EC relating to the reduc-
tion in the use of hazardous substances in electrical and electronic equipment and waste disposal.”
The basket symbol on equipment or on its box indicates that the product at the end of its useful life should be collected sep-
arately from other waste. The separate collection of this equipment at the end of its lifetime is organized and managed by
the producer. The user will have to contact the manufacturer and follow the rules that he adopted for end-of-life equipment
collection. The collection of the equipment for recycling, treatment and environmentally compatible disposal, helps to pre-
vent possible adverse e󰀨ects on the environment and health and promotes reuse and/or recycling of materials of the equip-
ment. Improper disposal of the product involves the application of administrative penalties as provided by the laws in force.
Equipment disposal

OPTIKA S.r.l.
Via Rigla, 30 - 24010 Ponteranica (BG) - ITALY Tel.: [phone]
[email protected] - www.optikamicroscopes.com
OPTIKA Spain
[email protected]
OPTIKA USA
[email protected]
OPTIKA China
[email protected]
OPTIKA India
[email protected]
OPTIKA Central America
[email protected]
®
®
®
®
®
®

Modello
C-HP4
Telecamere HDMI – Serie H
MANUALE DI ISTRUZIONI
Ver. 1.0 2021