Oracle MICROS Workstation 8 Assembly instructions

Page 1
POS Terminal
(Model: MICROS Workstation 8)
Basic Operation Guide

Page 2
Table of Contents
Overview of MICROS Workstation 8...............................................................................................3
Getting to know your Workstation................................................................................................3
MICROS Workstation 8 –Hardware Specification ......................................................................6
Using Your MICROS Workstation 8.................................................................................................7
Positioning Your MICROS Workstation 8 ....................................................................................7
Working with Windows®10..............................................................................................................8
Starting for the first time...............................................................................................................8
Turning off the Station..................................................................................................................8
Appendix –Regulatory Caution........................................................................................................9

Page 3
Overview of MICROS Workstation 8
Here introduce ORACLE new generation of POS Terminal, model MICROS
Workstation 8.
Getting to know your Workstation
MICROS Workstation 8 Front View
Figure 1-1: MICROS Workstation 8 Overview
Power button with LED indicator
14”touch LCD
Camera

Page 4
MICROS Workstation 8 Rear View
Figure 1-2: MICROS Workstation 8 Rear View
Hook (4 in total), to install the MICROS Workstation 8 on the Stand
Input, output interfaces

Page 5
MICROS Workstation 8 I/O View
Figure 1-3: MICROS Workstation 8 I/O View
USB C Out (5V/9V/15V)
Power to CFD (5V, 2A)
Micro USB LAN Port
Gigabit LAN
USB C Power In
Power from adaptor
CMOS reset button
Not end user use

Page 6
MICROS Workstation 8 –Hardware Specification
Specification
Parameter
Processor
Alt. supporting CPU sources:
Intel® Atom® 6000 Series processor
Intel® J6426 (2GHz, 4 core),
Intel® J6413 (1.6GHz, 4 core) ,
Intel® X6413E (1.5GHz,4 core)
Intel® X6211E (1.3G, 2 core)
Memory
Installed memory (RAM) up to 8GB
SSD up to 256GB
Display with touch
screen
LCD display
▪Type: TFT, supports transmissive display mode
▪Size: 14" TFT LCD Display
Network
Gigabit LAN
WIFI&BT
802.11a/b/g/n WIFI and Bluetooth module
RFID
13.56MHz and 125kHz
Modulation ASK
Button/Switch
One Power Button
Rating
DC 15V, 2A
Weight
About 0.8kg
Dimension
320 x 190 x 10 mm
Storage Temperature
-20 to 70 degrees Celsius
Operating Temperature
0 to 50 degrees Celsius
Passively cooled
Operating Humidity
Up to 90% relative humidity non condensing @ 50
Celsius

Page 7
Using Your MICROS Workstation 8
Positioning Your MICROS Workstation 8
1. Place the Vertical Stand or Low Profile Stand on a flat surface as a table or
desk.
2. Align and insert the Workstation on the docking plate, make sure all of four
hooks securely attach to the mounting holes of Stand.
3. Confirm the Workstation firmly lock on the Stand.
4. To remove the Workstation 8 from the Stand, press the unlock button to
release the Workstation
5. There are two Stands shown below for installing Workstation, mounting
methods are same.
Figure 2-1: Install the MICROS Workstation 8 on Low Profile Stand
Figure 2-2: Positioning the MICROS Workstation 8 to Vertical Stand
Unlock Button
MICROS Workstation 8
7 Inch Customer Display
7 Inch Customer Display
Vertical Stand
MICROS Workstation 8
Low Profile Stand

Page 8
Working with Windows®10
Starting for the first time
When you start your MICROS Workstation 8 for the first time, a series of
screens may appear to guide you configuring the basic setting of your
Windows®10 operating system.
Follow the instructions to configure.
Once you are done configuring the basic items, a Windows®10 Start screen
appears after successfully signing in to your user account. It helps organize all
the programs and applications you need in just one place.
Figure 2-2: Windows® 10 Start screen
Turning off the Station
Do either of the following to shut down your Station.
•Tap from the Charm bar then tap > shut down to do a normal
shutdown.
•From the log-in screen, tap > shut down.
•If your Workstation is unresponsive, press and hold the power button for
at least 4 seconds until your Express Station turns off.

Page 9
Appendix –Regulatory Caution
FCC Class A Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that
may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy, and if it is not installed and used in accordance with
the instruction manual, it may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference,
in which case the user will be required to correct the interference at his own expense.
Modifications: Any modifications made to this device that are not approved by Oracle
may void the authority granted to the user by the FCC to operate this equipment.
To satisfy FCC/IC RF exposure requirements, a separate distance of 20 cm or more
should be maintained between the antenna of this device and persons during device
operation.
To ensure compliance, operation at closer than this distance is not recommended.
Les antennes installées doivent être situées de facon àce que la population ne puisse
y être exposée àune distance de moin de 20 cm. Installer les antennes de facon àce
que le personnel ne puisse approcher à20 cm ou moins de la position centrale de l'
antenne.
La FCC des éltats-unis stipule que cet appareil doit être en tout temps éloignéd'au
moins 20 cm des personnes pendant son functionnement.
This device complies with Industry Canada's licence-exempt RSSs. Operation is
subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
(i)the device for operation in the band 5150-5250 MHz is only for indoor use to

Page
10
reduce the potential for harmful interference to co-channel mobile satellite
systems;
les dispositifs fonctionnant dans la bande de 5 150 à5 250 MHz sont réservés
uniquement pour une utilisation àl'intérieur afin de réduire les risques de
brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes
canaux;
(ii)the maximum antenna gain permitted for devices in the bands 5250-5350 MHz
and 5470-5725 MHz shall comply with the e.i.r.p. limit;
pour les dispositifs munis d'antennes amovibles, le gain maximal d'antenne
permis pour les dispositifs utilisant les bandes de 5 250 à5 350 MHz et de 5 470 à
5 725 MHz doit être conforme àla limite de la p.i.r.e;