Oregon Scientific RMR613HGA User manual

Wireless Thermo-Hygro Clock
Model : RMR613HGA
User Manual
RMR613HGA lab test cover R21/8/04, 7:02 PM1

EN
1
CONTENTS
Contents ................................................................... 1
Introduction .............................................................. 2
About Oregon Scientific .......................................... 2
Product Overview .................................................... 3
Front View .............................................................. 3
Back View .............................................................. 4
Remote Sensor (THGR122NX) ............................. 5
Getting Started ......................................................... 6
Batteries ................................................................. 6
Change Settings .................................................... 6
Table Stand ............................................................ 6
Remote Sensor (THGR122NX) ................................ 6
Setup Sensor ......................................................... 6
Data Transmission ................................................. 7
Search for Sensor .................................................. 8
Clock ......................................................................... 8
Turn Atomic Clock ON/OFF ................................... 9
Set Clock ............................................................... 9
Switch Clock Display ............................................. 9
Alarms ....................................................................... 9
View Alarm Settings ............................................... 9
Set Alarm ............................................................... 9
Activate Alarm ...................................................... 10
Silence Alarm ....................................................... 10
Temperature and Humidity .................................... 10
Select Temperature Unit ...................................... 10
Select Sensor Channel ........................................ 10
Minimum / Maximum Records ............................. 11
Comfort Zone ....................................................... 11
Reset System ......................................................... 11
Safety and Care ...................................................... 12
Warnings ................................................................. 12
Troubleshooting ..................................................... 12
Specifications ......................................................... 13
Main Unit Dimensions .......................................... 13
Remote Sensor Dimensions ................................ 13
Temperature ......................................................... 13
Relative Humidity ................................................. 13
Remote Sensor (THGR122NX) ........................... 13
Clock .................................................................... 13
Power ................................................................... 14
FCC Statement ....................................................... 14
RMR613HGA lab test R2 1/17/04, 5:00 PM1

EN
2
INTRODUCTION
Thank you for selecting the Oregon ScientificTM Wireless
Thermo-Hygro Clock (RMR613HGA). This device
bundles precise time keeping, dual alarm, and
temperature and humidity monitoring features into a
single tool you can use from the convenience of your
home.
In this box, you will find:
•Main unit
•Remote sensor (THGR122NX)
Keep this manual handy as you use your new product.
It contains practical step-by-step instructions, as well
as technical specifications and warnings you should
know.
ABOUT OREGON SCIENTIFIC
Visit our website (www.oregonscientific.com) to learn
more about other Oregon Scientific products such as
digital cameras, hand-held organizers, health and fitness
gear, and projection clocks. The website also includes
contact information for our customer service department,
in case you need to reach us.
RMR613HGA lab test R2 1/17/04, 5:00 PM2

EN
3
PRODUCT OVERVIEW
FRONT VIEW
1. Clock / Alarm Area: Date, time, dual alarm; and
Atomic Clock reception status
2. Temperature Area: Readings; sensor channel
number; remote unit reception and battery status
3. Humidity / Comfort Zone Area: Readings, comfort
zone and battery status.
4. Channel button: switch remote sensor
5. Alarm button: view alarm status; set alarm
1
2
3
4 5
RMR613HGA lab test R2 1/17/04, 5:00 PM3

EN
4
BACK VIEW
1. MEM: view current, maximum, and minimum
temperature / humidity readings
2. DOWN: decrease setting / deactivate radio-
controlled clock / activate or deactivate alarm
3. UP: increase setting / activate radio-controlled clock /
activate or deactivate alarm
4. MODE: change display / settings
5. Battery compartment
6. °C / °F switch
7. RESET hole
3
4
1
2
5, 6, 7
RMR613HGA lab test R2 1/17/04, 5:00 PM4

EN
5
REMOTE SENSOR (THGR122NX)
1. LCD display
2. LED Status indicator
1
2
1
2
3
4
1. Wall mount hole
2. RESET
3. Channel number (1 - 3)
4. Battery compartment
(Battery compartment cover not shown)
RMR613HGA lab test R2 1/17/04, 5:00 PM5

EN
6
CHANGE SETTINGS
1. Press and hold MODE for 2 seconds to enter setting
mode.
2. Press UP or DOWN to change settings.
3. Press MODE to confirm.
REMOTE SENSOR (THGR122NX)
This product is shipped with a THGR122NX Thermo/
Hygro Sensor that collects Temperature and Humidity
data. Data can be collected from up to 3 sensors.
Additional sensors sold separately.
SETUP SENSOR
Open the remote sensor battery compartment with a
small Phillips screwdriver.
GETTING STARTED
BATTERIES
Batteries are not supplied with this product. You will need
to purchase 2 x UM-3 (AA) 1.5V alkaline batteries for
the main unit, and 2 x UM-4 (AAA) 1.5V alkaline batteries
for the remote sensor.
Insert the batteries before first use, matching the polarity
as shown in the battery compartment. For best results,
install batteries in the remote sensor before the main
unit. Press RESET after each battery change.
Do not use rechargeable batteries.
NOTE
UNIT LOCATION
MainTemperature Area when
the INDOOR temperature
is shown.
Remote Temperature Area when the
OUTDOOR temperature is
shown.
shows when batteries are low.
RMR613HGA lab test R2 1/17/04, 5:00 PM6

EN
7
3. Place the sensor near the main unit. Press RESET
on the sensor to initiate signal sending between the
sensor and the main unit. The reception icon on
the main unit will blink for approximately 3 minutes
while it is searching for the sensor. (Refer to the
Search for Sensor section for more information.)
4. Close the remote sensor battery compartment.
5. Secure the sensor in the desired location using the
wall mount or table stand.
1. Insert the batteries, matching the polarity as shown
in the battery compartment.
2. Set the channel. The switch is located in the battery
compartment.
SWITCH OPTION
Channel Channel 1 - 3. If you are using
more than one sensor, select a
different channel for each sensor.
For best results:
•Insert the batteries and select the channel and
temperature unit before you mount the sensor.
•Place the sensor out of direct sunlight and
moisture.
•Do not place the sensor more than 30 meters
(98 feet) from the main (indoor) unit.
•Position the sensor so that it faces the main
(indoor) unit, minimizing obstructions such as
doors, walls, and furniture.
•Place the sensor in a location with a clear view
to the sky, away from metallic or electronic
objects.
•Position the sensor close to the main unit during
cold winter months as below-freezing
temperatures may affect battery performance
and signal transmission.
You may need to experiment with various locations to
get the best results.
DATA TRANSMISSION
Data is sent from the sensor(s) every 40 seconds.
The reception icon shown in the Temperature and
Humidity Areas show the status.
RMR613HGA lab test R2 1/17/04, 5:00 PM7

EN
8
SEARCH FOR SENSOR
To search for a sensor, press and hold MEM and
CHANNEL for 2 seconds.
If the sensor is still not found, check the
batteries, obstructions, and remote unit location.
Signals from household devices such as
doorbells, electronic garage doors, and home security
systems may cause temporary reception failure. This is
normal and does not affect general product performance.
The reception will resume once the interference ends.
NOTE
--- shows in Temp
/ Humidity Areas
ICON DESCRIPTION
Main unit is searching for
sensors.
At least 1 channel has
been found.
Channel 1 is selected
(number will change
depending on the sensor
you select)
The selected sensor cannot
be found. Search for the
sensor or check batteries.
NOTE
CLOCK
This product can track the date and time for up to
2 locations (Clock with Offset Hour). The US Atomic
Clock in Boulder, Colorado automatically updates this
information unless you disable the feature. The signals
are collected by the main unit when it is within 1500 km
(932 miles) of a signal.
Initial reception takes 2 - 10 minutes, and is initiated
when you first setup the unit, and whenever you press
RESET. Once complete, the reception icon will stop
blinking. The icon is shown in the Clock Area.
To force a manual search for Atomic Clock signals, press
and hold UP for 2 seconds. If no signal is found, check
the batteries.
If the Atomic Clock signal is received and the
hour is incorrect, use the "hour offset" feature to adjust
it to to the right value. Please see "SET CLOCK" on
pg. 9 for instructions.
NOTE
RMR613HGA lab test R2 1/17/04, 5:00 PM8

EN
9
TURN ATOMIC CLOCK ON/OFF
Perform this step if you cannot receive Atomic Clock
signals. Press and hold DOWN for 2 seconds. Then,
manually set the clock following the “Set Clock”
instructions (below).
SET CLOCK
You only need to do this if you have disabled the Atomic
Clock feature (for example, if you are too far from or
cannot receive a signal).
1. Press and hold MODE for 2 seconds. The Clock
Area will blink.
2. Select the offset hour, 12 / 24 hour format, hour,
minute, year, month, day, and language. Press UP
or DOWN to change the setting. Press MODE to
confirm.
The language options are (E) English,
(F) French, (D) German, (I) Italian, and (S) Spanish.
The signal icon indicates that the Atomic Clock
feature is ON. No icon means that it is OFF
SWITCH CLOCK DISPLAY
Press MODE to toggle between Clock with Seconds,
Clock with Weekday and Calendar, and Clock with Offset
Hour display.
ALARMS
This product has 2 alarms: a Single Alarm and a Weekday
Alarm. The Single Alarm can be set to go off at a specific
time for a one-time event (for example, if you are napping
on Saturday). The Weekday Alarm will sound at the same
time Monday - Friday (but not on weekends).
VIEW ALARM SETTINGS
Press ALARM to display the Alarm settings you wish to
view: Weekday Wor Single S.
SET ALARM
1. Press ALARM to display the type of Alarm you wish
to set: Weekday or Single.
2. Press and hold ALARM for 2 seconds. The Alarm
settings will blink.
3. Select the hour and minute. Press UP or DOWN to
change settings. Press ALARM to confirm.
NOTE
RMR613HGA lab test R2 1/17/04, 5:00 PM9