ORiNG ITGMC-111GP+ User manual

Quick Installation Guide
Version 1.0
Quick Installation Guide
Introduction
PRINTED ON RECYCLED PAPER
QIG ITGMC-111GP+ 1907-2-29-ITGMC111GP+-1.0
The is a cost-effective solution for interface conversion
between 1G/10GBase-T and 1G/10GBase-X SFP+ socket. It allows you to
extend communication distance of Gigabit copper port with optical fiber. The
supports MDI/MDIX auto detection, so you don’t need to use
crossover wires. With a wide operating temperature range from -20~60 C
and a wide voltage range from dual 12~48 VDC power inputs, the
is suitable for harsh operating environments. Therefore, the
is one of the most reliable media converters in harsh industrial
environments.
ITGMC-111GP+
ITGMC-111GP+
ITGMC-
111GP+ ITGMC-
111GP+
o
Package Contents
Installation
The series is shipped with the following items. If any of these items is missing
or damaged, please contact your customer service representative for
assistance.
Preparation
Before installation, make sure you have all of the package contents
available and a PC with Microsoft Internet Explorer 6.0 or later, for using
web-based system management tools.
Elevated Operating Ambient:
Reduced Air Flow:
If installed in a closed cabinet, the operating
ambient temperature of the rack environment may be greater than room ambient.
Therefore, consideration should be given to installing the equipment in an
environment compatible with the maximum ambient temperature (Tma) specified
by the manufacturer.
Installation of the equipment should be such that the
amount of air flow required for safe operation of the equipment is not
compromised.
Mechanical Loading:
Circuit Overloading:
Mounting of the equipment in the d should be
such that a hazardous condition is not achieved due to uneven mechanical
loading.
Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
in-rail
Safety & Warnings
Dimension (Unit: mm)
Step 1:
Step 2:
Slant the switch and screw the Din-rail kit onto the back of the switch, right in the
middle of the back panel.
Slide the switch onto a DIN-rail from the Din-rail kit and make sure the switch clicks into
the rail firmly.
DIN-rail Installation
Media
Converter
Media
Converter
INDUSTRIAL
ITGMC-111GP+
Panel Layouts
Front Panel
1. Power LED
2. Relay LED
3. DIP switch for relay
4. LNK/ACT LED for 10G copper port
5. 10G port
6. Speed LED for 10G SFP port
7. LNK/ACT LED for 10G SFP port
8. 10G SFP port
Top Panel
2
1. Terminal block
2. Grounding
Real Panel
1. Wall-mount screw holes
2. Din-rail screw holes
1
3
Industrial Gigabit Media Converter
Contents
ITGMC-111GP+
Pictures Number
X1
QIG X1
DIN-rail kit X1
Wall-Mount Kit X2
ITGMC-111GP+
2
4
5
67
8
1
1
1
2
Wall-mount
Step 1:
Step 2:
Step 3:
Screw the two pieces of wall-mount kits to the top and bottom panels of the device. A
total of screws are required, as shown below.
Use the device, with wall mount plates attached, as a guide to mark the correct locations
of the four screws.
Insert a screw head through middle of the keyhole-shaped aperture on the plate, and
then slide the device downwards. Tighten the screw head for added stability.
eight
Network Connection
The device has two 10/100Base-T(X) Ethernet ports. According to the link type, the AP uses
CAT 3, 4, 5, 5e, 6 UTP cables to connect to any other network device (PCs, servers,
switches, routers, or hubs).
Cable Types and Specifications:
Cable
Type
Max. Length
Connector
10BASE-T Cat. 3 , 4, 5 100-ohm UTP 100 m (328 ft ) RJ-45
100BASE-TX Cat. 5 100 -ohm UTP UTP 100 m (328 ft) RJ-45

QIG Quick Installation Guide
PRINTED ON RECYCLED PAPER
Quick Installation Guide
Power Input
The switch supports triple redundant power supplies which are
located on a 7-pin terminal block.
Insert the negative/positive wires into the V-/V+ terminals,
respectively.
To keep the DC wires from pulling loose, use a small flat-
blade screwdriver to tighten the wire-clamp screws on the front of the
terminal block connector.
STEP 1:
STEP 2:
Version 1.0
QIG
Configurations
After installing the device and connecting cables, the green power LED
should turn on. Please refer to the following tablet for LED indication.
LED indication table
Specifications
Wiring
For pin assignments for different types of cables, please refer to the following tables.
Media
Converter
Media
Converter
INDUSTRIAL
ORing Media Converter Model ITGMC-111GP+
1G/10GBase-T in RJ45 Auto
MDI/MDIX
Physical Ports
Technology
Ethernet standards
IEEE 802.3ae for 10Gigabit Ethernet
IEEE 802.3an for 10GBase-T
IEEE 802.3ab for 1000Base-T
IEEE 802.3z for 1000Base-X
Power
Input power
Power consumption(Typ.)
Dual12~48VDCvoltagepowerinputsin6pinterminalblock
8.6 Watts
Overload current protection
Reverse polarity protection
Present
Present on terminal block
Physical Characteristic
Enclosure IP-30
Dimension(WxDxH) 40(W)x108(D)x154(H)mm(1.57x4.25x6.02inch)
Weight ( g)
1(*Note)
Jumbo Frame 10K
437g
Fault contact
Relay Relayoutputtocarrycapacityof1Aat24VDCatpinterminalblock
Regulatory Approvals
FCC Part 15, CISPR (EN55022) class A
EMI
EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge),
EN61000-4-6 (CS), EN61000-4-8, EN61000-4-11
EMS
IEC60068-2-27
Shock
IEC60068-2-6
IEC60068-2-32
Vibration
Free Fall
100/1000Base-X SFP port 1
Environmental
-40to85C(-40to185F)
oo
Storage Temperature
Operating Temperature
5% to 95% Non-condensing
Operating Humidity
-20to60C(-4to140F)
oo
MTBF
TBD
Warranty
5years
1G/10G Base -T(X) RJ-45 Pin Ass ignments
Pin Number
Assignment
1TD+
2TD-
3RD+
4Notused
5Notused
6RD-
7Notused
8Notused
1G/10G Base-T MDI/MDI-X Pi n Assignmen ts
Pin Nu mber
MDI port
MDI-X por t
1 TD+(transmit) RD+(receive)
2 TD-(transmit) RD-(receive)
3 RD+(receive) TD+(transmit )
4 Not used Not used
5 Not used Not used
6 RD-(receive) TD-(tra nsmit)
7 Not used Not used
8 Not used Not used
Fiber Cables
The device comes with a SFP fiber optical port. The fiber optical ports are in multi-
mode (0 to 550M, 850 nm with 50/125 m, 62.5/125 m fiber) and single-mode with
LC connectors. Please remember that the TX port of Switch A should be connected to
the RX port of Switch B.
LED
Color
Status
Description
PW1 Green On DC power module 1 activated
PW2 Green On DC power module 2 activated
Relay Amber
On Relay activated (closed)
Off Relay de-activated (opened)
LED for SFP Port
LNK/ACT Green On Port is linked
LED for RJ45 Port
LNK/ACT Green On Port is linked
Speed
Green On Port is running at 10Gbps
Amber On Port is running at 1Gbps
ORing Industrial Networking Corp.
Copyright© 2017 ORing
All rights reserved.
TEL: [phone]
FAX: [phone]
Website: www.oring-networking.com
E-mail: [email protected]
*Note:10GBase-TmustuseshieldingtwistedpaircableofCat6aorabove.
ITGMC-111GP+
ITGMC-111GP+ Industrial Gigabit Media Converter