ORiNG TPS-3082GF-MM-M12-QODC User manual

Quick Installation Guide
Version 1.0
Quick Installation Guide
Introduction
PRINTED ON RECYCLED PAPER
QIG
The is a managed Ethernet switch
designed for rolling stock, vehicle, and railway applications. The switch
boasts EN50155 compliance and M12 connectors to ensure tight and robust
connections in harsh environments where vibration and shock will cause
disturbances. With eight 10/100Base-T(X) P.S.E. ports, the switch can
provide power for IEEE 802.3af-compliant devices over an Ethernet cable
without using additional power. The device also provides two Gigabit fiber
ports in Q-ODC connector for long-distance connections. With complete
support for Ethernet redundancy protocols such as O-Ring (recovery time <
10ms over 250 units of connection), Open-Ring and MSTP/RSTP/STP (IEEE
802.1s/w/D), the switch can protect your mission-critical applications from
network interruptions or temporary malfunctions. Featuring a wide operating
temperature from -40 C to 70 C, the switch can be managed centrally via
Open-Vision, web browsers, Telnet and console (CLI) configuration.
TPS-3082GF-MM-M12-QODC
oo
Package Contents
Installation
Wall-mount
The device can be fixed to the wall. Follow the steps below to install the device on the wall.
Hold the evice upright against the wall
Insert four screws through the large opening of the keyhole-shaped apertures at the
top and bottom of the unit and fasten the screw to the wall with a screwdriver.
Slide the evice downwards and tighten the four screws for added stability.
Step 1:
Step 2:
Step 3:
d
d
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative for
assistance.
Preparation
Before you begin installing the device, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient:
Reduced Air Flow:
Mechanical Loading:
Circuit Overloading:
If installed in a closed environment, make sure
the operating ambient temperature is compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Make sure the amount of air flow required for safe operation
of the equipment is not compromised during installation.
Make sure the mounting of the equipment is not in a
hazardous condition due to uneven mechanical loading.
Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
Safety & Warnings
For pin assignments of power, console and relay output ports, please refer to the following tables.
Contents
TPS-3082GF-MM-M12-QODC
Pictures Number
1
CD 1
Dimension
Panel Layouts
Front View
1. Reset button
2. Power module indicators
3. R.M. status LED
4. Ring status LED
5. Fault LED
6.Relayoutputport
7. Console port
8. Power connector
9. PoE fast Ethernet ports
10. LNK/ACT indicator for PoE Fast Ethernet
port
11. PoE status LED for PoE Ethernet ports
12. Duplex/collision indicator for
PoE Ethernet port
13. Gigabit fiber ports
14. LNK/ACT indicator for gigabit fiber port
Wiring
Grounding
Grounding and wire routing help limit the effects of noise due to electromagnetic interference
(EMI). Run the ground connection from the grounding pin on the power connector to the grounding
surface prior to connecting devices.
Power port pinouts
The device supports two sets of power supplies and uses the M23 5-pin
female connector on the front panel for the dual power inputs.
Insert a power cable to the power connector on the device.
Rotate the outer ring of the cable connector until a snug fit is
achieved. Make sure the connection is tight.
Step 1:
Step 2:
V1+
V1-
V2+
V2-
Relay output port pinouts
Relay N.C.
3A@24VDC
Network Connection
The switch has eight 10/100Base-T(X) and two Gigabit fiber ports in the form of M12 connector.
Depending on the link type, the switch uses CAT 3, 4, 5,5e UTP cables to connect to network
devices (PCs, servers, switches, routers, or hubs). Please refer to the following table for cable
specifications.
4-Pin PoE Port Definition
TPS-3082GF-MM-M12-QODC
TPS-3082GF-MM-M12-QODC 1907-2-29-TPS3082GFM12QODC-1.0
Switch
EN50155
EN50155 10-port managed
PoE Ethernet switch
INDUSTRIAL
Instead of screwing the screws in all the way, it is advised to
leave a space of about 2mm to allow room for sliding the
switch between the wall and the screws.
The switch uses the M12 A-coded 5-pin female connector
on the front panel for relay output. Use a cable with an M12
A-coded 5-pin male connector to connect the relay. The
relay contacts will detect user-configured events and form
an open circuit when an event is triggered.
Cable Type Max. Length Connector
10BASE-T Cat. 3 , 4, 5 100-ohm UTP 100 m (328 ft) 4-pin fem ale M12
D-coding connector
100BASE-TX Cat. 5 100-ohm UTP UTP 100 m (328 ft)
4-pin fem ale M12
D-coding connector
For pin assignments of the LAN ports, please refer to the following tables.
QIG 1
1
Tx+
2
Rx+
Tx-
3
Rx-
4
Gigabit Fiber Port
Console port pinouts
N.C.
RXD
RS-232, 9600bps, 8, N, 1
GND
TXD
N.C.
1
7
8
9
12
10
11
13
45
6
23
Pin No. Description
#1 TD+ with PoE Vout +
#2 RD+ with PoE Vout -
#3 TD- wit h PoE Vout +
#4 RD- wi th PoE Vout -
* Notice: Please connect the cable in correct polarity
Tx+ Rx+
Tx-Rx-
Tx+:PoEVout+
Tx-: PoE Vout+
Rx+:PoEVout-
Rx-:PoE Vout-
3A@24VDC
Relay N.C.
N.C.
RXD
RS-232,9600bps,8, N, 1
GND
TXD
N.C.
V1+
V1-
V2+
V2-
TPS-3082GF-M12
Tx+ Rx+
Tx-Rx-
Tx+:PoE Vout+
Tx-: PoE Vout+
Rx+:PoE Vout-
Rx-: PoE Vout-
3A@24VDC
Relay N.C.
N.C.
RXD
RS-232,9600bps,8,N,1
GND
TXD
N.C.
V1+
V1-
V2+
V2-
TPS-3082GF-M12
14

QIG Quick Installation Guide
PRINTED ON RECYCLED PAPER
Quick Installation Guide
ORing Industrial Networking Corp.
Copyright© 2016 ORing
All rights reserved.
TEL: [phone]
FAX: [phone]
Website: www.oring-networking.com
E-mail: [email protected]
Version 1.0
QIG
Specifications
Switch
EN50155
INDUSTRIAL
Physical Characteristic
Enclosure IP-30
Dimension(WxDxH) 212(W) x 75(D) x 198(H) mm (8.35 x 2.95 x 7.8 inch.)
Weig ht ( g) 1462g
Environmental
-40to85C(-40to185F)
oo
Storage Temperature
5% to 95% Non-condensing
Operating Humidity
Regulatory Approvals
FCC Part 15, CISPR (EN55022) class A, EN50155 (EN50121-3-2, EN55011, EN50121-4)
EMI
EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge),
EN61000-4-6 (CS), EN61000-4-8, EN61000-4-11
EMS
IEC60068-2-27
Shock
IEC60068-2-32
IEC60068-2-6
Vibration
Free Fall
Warranty
5 years
EN60950-1
Safety
-40to70C(-40to158F)
oo
Operating Temperature
ORing Switch Model
10/100 Base-T(X) Ports in M12 Auto
MDI/MDIX with P.S.E. 8xM12connector(4pinD-coding)
Physical Ports
Technology
Ethernet Standards
IEEE 802.3 for 10Base-T
IEEE 802.3u for 100Base-TX
IEEE 802.3z for 1000Base-X
IEEE 802.3x for Flow control
IEEE 802.3ad for LACP (Link Aggregation Control Protocol)
IEEE 802.1D for STP (Spanning Tree Protocol)
IEEE 802.1p for COS (Class of Service)
IEEE 802.1Q for VLAN Tagging
IEEE 802.1w for RSTP (Rapid Spanning Tree Protocol)
IEEE 802.1s for MSTP (Multiple Spanning Tree Protocol)
IEEE 802.1x for Authentication
IEEE 802.1AB for LLDP (Link Layer Discovery Protocol)
IEEE 802.3af PoE specification (up to 15.4 Watts per port for P.S.E.)
8192 MAC addresses
MAC Table
4
Priority Queues
TPS-3082GF-MM-M12-QODC
1. Launch the Internet Explorer and type in IP address of the device. The default static
IP address is 192.168.10.1
Follow the steps below to log in and access the system:
2. Log in with default user name and password (both are ).admin
3. After logging in, you should see the following screen. For more information on
configurations, please refer to the user manual. For information on operating the device
using ORing’s Open-Vision management utility, please go to ORing website.
Resetting
To restore the device configurations back to the factory defaults, press the button for a
few seconds. Once the power indicator starts to flash, release the button. The device will then
reboot and return to factory defaults.
Reset
RS-232 Serial Console Port RS-232 in M12 connector (5-pin A-coding). Baud rate setting: 9600bps, 8, N, 1
Store-and-Forward
Processing
Switch Properties
Switching latency: 7 us
Switching bandwidth: 5.6 Gbps
Max. Number of Available VLANs: 4096
IGMP multicast groups: 1024
Port rate limiting: User Define
Configurations
After installing the and connecting cables, start the evice by
turning on power. The green power LED should turn on. Please refer to the
following table for LED indication.
switch d
1000Base-SX Fiber Ports in
Q-ODC connector 2 x Q-ODC connector
EN50155 10-port managed
PoE Ethernet switch
LED Color Statu s Descrip tion
PWR1 Green On DC power module 1 activated
PWR2 Green On DC power module 2 activated
R.M Green On System running in Ring Master mode
Ring Green On System running i n Ring mode
Faul t Amber On System errors (power failure or p ort li nk down)
10/100Base-T(X) Ports
On Port is linked
LNK/ACT Green
Blinking Transmitting data
PoE Green On Port providi ng power to PD
On Port runnin g in f ull-duplex mode
DPX/ COL Amber
Blinki ng Collision occurs
Gigabit Fiber Ports
On Port is linked
LNK/ACT Green
Blinking Transmitting data
Fiber Ports Number 2
Fiber Port Specification
Fiber Diameter (µm) 62.5/125 50/125µm@ µm
Fiber Optical Connector Q-ODC
Typical Distance (Km) 0.55 Km
Wavelength (nm) 850 nm
Max. Output Optical Power (dbm) -4 dbm
Min. Output Optical Power (dbm) -9.5 dbm
Max. Input Optical Power
Saturation() 0dbm
Min. Input Optical Power
Sensitivity() -18 dbm
Link Budget (db) 8.5 db
Fiber Ports Standard 1000Base-SX
Fiber Mode Multi-mode
Security Features
Enable/disable ports, MAC based port security
Port based network access control (802.1x)
VLAN (802.1Q) to segregate and secure network traffic
Supports Q-in-Q VLAN for performance & security to expand the VLAN space
Radius centralized password management
SNMP v1/v2c/v3 encrypted authentication and access security
Software Features
STP/RSTP/MSTP (IEEE 802.1D/w/s)
Redundant Ring (O-Ring) with recovery time less than 10ms over 250units
TOS/Diffserv supported
Quality of Service (802.1p) for real-time traffic
VLAN (802.1Q) with VLAN tagging and GVRP supported
IGMP Snooping for multicast filtering
Port configuration, status, statistics, monitoring, security
SNTP for synchronizing of clocks over network
Support PTP Client (Precision Time Protocol) clock synchronization
DHCP Server / Client support
Port Trunk support
MVR (Multicast VLAN Registration) support
Power
Redundant Input Power
Power Consumption(Typ.)
DualDCinputs.48VDCon5-pinM23connector
10.75 Watts
Fault Contact
Relay Relay output to carry capacity of 3A at 24VDC on M12 connector (5-pin M12 A-coding)
Overload Current Protection
Reverse Polarity Protection
Present
Present
Network Redundancy
O-Ring
Open-Ring
O-Chain
STP
RSTP
MSTP
Warning / Monitoring System
Relay output for fault event alarming
Syslog server / client to record and view events
Include SMTP for event warning notification via email
Event selection support
PoE Output Power 120 Watts
TPS-3082GF-MM-M12-QODC
TPS-3082GF-MM-M12-QODC