ORiNG IES-3080 Series User manual

I
IE ES S- -3 30 08 80 0 / / I IE ES S- -3 30 06 62 2 S Se er ri ie es s
I
In nd du us st tr ri ia al l M Ma an na ag ge ed d E Et th he er rn ne et t S Sw wi it tc ch he es s
U
Us se er r M Ma an nu ua al l
V
Ve er rs si io on n 4 4. .0 0
J
Ja an nu ua ar ry y, , 2 20 01 14 4
w
ww ww w. .o or ri in ng g- -n ne et tw wo or rk ki in ng g. .c co om m

IES-3080 / IES-3062 Series User Manual
ORing Industrial Networking Corp
1
COPYRIGHT NOTICE
Copyright © 2014 ORing Industrial Networking Corp.
All rights reserved.
No part of this publication may be reproduced in any form without the prior written consent of
ORing Industrial Networking Corp.
TRADEMARKS
is a registered trademark of ORing Industrial Networking Corp.
All other trademarks belong to their respective owners.
REGULATORY COMPLIANCE STATEMENT
Product(s) associated with this publication complies/comply with all applicable regulations.
Please refer to the Technical Specifications section for more details.
WARRANTY
ORing warrants that all ORing products are free from defects in material and workmanship for
a specified warranty period from the invoice date (5 years for most products). ORing will repair
or replace products found by ORing to be defective within this warranty period, with shipment
expenses apportioned by ORing and the distributor. This warranty does not cover product
modifications or repairs done by persons other than ORing-approved personnel, and this
warranty does not apply to ORing products that are misused, abused, improperly installed, or
damaged by accidents.
Please refer to the Technical Specifications section for the actual warranty period(s) of the
product(s) associated with this publication.
DISCLAIMER
Information in this publication is intended to be accurate. ORing shall not be responsible for its
use or infringements on third-parties as a result of its use. There may occasionally be
unintentional errors on this publication. ORing reserves the right to revise the contents of this
publication without notice.
CONTACT INFORMATION
ORing Industrial Networking Corp.
4F., NO.3, Lane235, Baociao Rd., Sindian City, Taipei County 23145, Taiwan, R.O.C.
Tel: + 886 2 2918 3036 // Fax: + 886 2 2918 3084
Website: www.oring-networking.com
Technical Support
E-mail: [e-mail]
Sales Contact
E-mail: [e-mail] (Headquarters)
[e-mail] (China)

IES-3080 / IES-3062 Series User Manual
ORing Industrial Networking Corp
2
Table of Content
Getting Started...............................................................................................5
1.1 About IES-3080 / IES-3062 Series...............................................................................5
1.2 Software Features .........................................................................................................5
1.3 Hardware Features........................................................................................................5
Hardware Overview........................................................................................7
2.1 Front Panel.....................................................................................................................7
2.2 Front Panel LEDs ........................................................................................................10
2.3 Top Panel......................................................................................................................10
2.4 Rear Panel ...................................................................................................................11
Hardware Installation...................................................................................12
3.1 DIN-rail Installation ......................................................................................................12
3.2 Wall Mounting...............................................................................................................13
3.3 Wiring............................................................................................................................14
3.3.1 Grounding............................................................................................................15
3.3.2 Redundant Power Inputs ....................................................................................15
3.4 Connection...................................................................................................................15
3.4.1 Cables..................................................................................................................15
3.4.2 O-Ring/O-Chain...................................................................................................17
Redundancy .................................................................................................20
4.1 O-Ring..........................................................................................................................20
4.1.1 Introduction..........................................................................................................20
4.1.2 Configurations......................................................................................................20
4.2 OPEN-Ring...................................................................................................................22
4.2.1 Introduction..........................................................................................................22
4.2.2 Configurations......................................................................................................22
4.3 O-Chain........................................................................................................................23
4.3.1 Introduction..........................................................................................................23
4.3.2 Configurations......................................................................................................23
4.4 MRP..............................................................................................................................24
4.4.1 Introduction..........................................................................................................24
4.4.2 Configurations......................................................................................................24
4.5 STP/RSTP/MSTP........................................................................................................25
4.5.1 STP/RSTP ...........................................................................................................25

IES-3080 / IES-3062 Series User Manual
ORing Industrial Networking Corp
3
4.5.2 MSTP ...................................................................................................................29
4.6 Fast Recovery..............................................................................................................33
Management.................................................................................................35
5.1 System Information.............................................................................................36
5.2 Basic Setting ......................................................................................................37
5.2.1 Admin Password ........................................................................................38
5.2.2 IP Setting...................................................................................................38
5.2.3 Time Setting...............................................................................................39
5.2.4 LLDP..........................................................................................................42
5.2.5 Modbus TCP..............................................................................................43
5.2.6 Backup & Restore ......................................................................................44
5.2.7 Upgrade Firmware......................................................................................45
5.3 Multicast.........................................................................................................45
5.3.1 IGMP Snooping..........................................................................................45
5.3.2 MVR...........................................................................................................46
5.3.3 Static Multicast Filtering..............................................................................47
5.4 Port Setting ....................................................................................................48
5.4.1 Port Control................................................................................................48
5.4.2 Port Status .................................................................................................48
5.4.3 Port Alias....................................................................................................49
5.4.4 Rate Limit...................................................................................................49
5.4.5 Port Trunk ..................................................................................................50
5.4.6 Loop Guard................................................................................................51
5.5 VLAN .............................................................................................................51
5.5.1 VLAN Setting..............................................................................................51
5.5.2 Port Based.................................................................................................53
5.6 Traffic Prioritization.........................................................................................54
5.6.1 QoS Policy.................................................................................................55
5.6.2 Port-base priority........................................................................................56
5.6.3 COS/802.1p...............................................................................................56
5.6.4 TOS/DSCP.................................................................................................57
5.7 DHCP Server..................................................................................................57
5.7.1 Basic Setting..............................................................................................58
5.7.2 Client List...................................................................................................59
5.7.3 Port and IP bindings...................................................................................59
5.7.4 DHCP Relay Agent.....................................................................................59
5.8 SNMP.............................................................................................................60

IES-3080 / IES-3062 Series User Manual
ORing Industrial Networking Corp
4
5.8.1 Agent Setting..............................................................................................60
5.8.2 Trap Setting................................................................................................62
5.8.3 SNMPV3....................................................................................................62
5.9 Security....................................................................................................................65
5.9.1 IP Security..................................................................................................65
5.9.2 Port Security...............................................................................................66
5.9.3 MAC Blacklist.............................................................................................66
5.9.4 802.1x........................................................................................................67
5.9.5 IP Guard.....................................................................................................70
5.10 Warning....................................................................................................................72
5.10.1 Fault Relay Alarm...................................................................................72
5.10.2 SYSLOG................................................................................................72
5.10.3 SMTP.....................................................................................................73
5.10.4 Event Notification...................................................................................74
5.11 Monitor and Diag.....................................................................................................75
5.11.1 System Event Log..................................................................................75
5.11.2 MAC Address Table................................................................................76
5.11.3 Ping.......................................................................................................82
5.11.4 Save Configuration.........................................................................................83
5.11.5 Factory Default...............................................................................................83
5.11.6 System Reboot...............................................................................................83
Command Line Interface Management ......................................................85
Technical Specifications12345678............................................................110

IES-3080 / IES-3062 Series User Manual
ORing Industrial Networking Corp
5
Getting Started
1.1 About IES-3080 / IES-3062 Series
The IES-3000 series are powerful managed industrial switches designed for harsh, dusty, and
humid environments. The series consists of the IES-3080, IES-3062GT, IES-3062FX, and
IES-3062GF models to meet customers’needs for different applications. The devices can be
managed via web browsers, TELNET, Console or other third-party SNMP software as well as
ORing’s proprietary management utility Open-Vision. The user-friendly and powerful interface
of Open-Vision allows you to easily configure and monitor multiple switches at the same time.
1.2 Software Features
Supports O-Ring (Recovery time < 10ms over 250 units connection)
Supports Open-Ring to interoperate with other vendors’ring technology in open
architecture
Supports O-Chain to allow multiple redundant network rings
Supports standard IEC 62439-2 MRP (Media Redundancy Protocol) function
Supports MSTP/RSTP/STP (IEEE 802.1s/w/D)
Supports PTP client (Precision Time Protocol) clock synchronization
Supports Modbus/TCP protocol
Supports IGMP v2/v3 (IGMP snooping support) for filtering multicast traffic
Port Trunking for easy of bandwidth management
Supports SNMP v1/v2c/v3 for network security
Supports RMON for traffic monitoring
Supports LLDP protocol
Supports event notification through SYSLOG, e-mail, SNMP traps, and relay output
Supports port lock to prevent access from unauthorized MAC address
Supports management via Web-based interfaces, Telnet, Console (CLI), and Windows
utility (Open-Vision)
1.3 Hardware Features
Dual DC power inputs
8 or 6 x 10/100Base-T(X) Ethernet ports (IES-A3080 or IES-A3062GT/GF/FX)
2 x 10/100/1000Base-T(X) ports (IES-A3062GT)
2 x 100Base fiber ports (IES-A3062FX)

IES-3080 / IES-3062 Series User Manual
ORing Industrial Networking Corp
6
2 x 1000Base fiber ports (IES-A3062GF)
1 x console port
Wide Operating Temperature: -40 to 70oC
Storage Temperature: -40 to 85oC
Operating Humidity: 5% to 95%, non-condensing
Casing: IP-30
Dimensions: 52mm (W) x 106mm (D) x 144mm (H)

IES-3080 / IES-3062 Series User Manual
ORing Industrial Networking Corp
7
Hardware Overview
2.1 Front Panel
The IES-3000 series include the following models, each with different port combinations.
Models
Description
IES-3080
Industrial C1D2/ATEX 8-port managed Ethernet switch
with 8x10/100Base-T(X)
IES-3062GT
Industrial C1D2/ATEX 8-port managed Ethernet switch
with 6x10/100Base-T(X) and 2x10/100/1000Base-T(X)
IES-3062FX
IES-3062FX-MM
Industrial C1D2/ATEX 8-port managed Ethernet switch
with 6x10/100Base-T(X) and 2x100Base-FX, multi-mode
IES-3062FX-SS
Industrial C1D2/ATEX 8-port managed Ethernet switch
with 6x10/100Base-T(X) and 2x100Base-FX,
single-mode
IES-3062GF
IES-3062GF-MM
Industrial C1D2/ATEX 8-port managed Ethernet switch
with 6x10/100Base-T(X) and 2x1000Base-SX,
multi-mode
IES-3062GF-SS
Industrial C1D2/ATEX 8-port managed Ethernet switch
with 6x10/100Base-T(X) and 2x1000Base-LX,
single-mode
The switches come with the following ports on the front panel:
Port
Description
10/100 RJ-45 fast
Ethernet ports
IES-3080: 8 x 10/100Base-T(X) RJ-45 fast Ethernet ports with
auto-negotiation support.
IES-3062GT/GF/FX: 6 x 10/100Base-T(X) RJ-45 fast Ethernet
ports with auto-negotiation support
Gigabit RJ-45 port
IES-3062GT: 2 x 10/100/1000Base-T(X) ports
Fiber port
IES-3062GF: 2 x 1000BaseX ports

IES-3080 / IES-3062 Series User Manual
ORing Industrial Networking Corp
8
IES-A3062FX: 2 x 100BaseFX ports
Console
1 x console port for managing switch via a RS-232 to RJ-45 cable
Reset
Push reset button 2 to 3 seconds to reset the switch.
Push reset button 5 seconds to return the switch to factory
setting.
IES-3080/3062GT
1. Power 1 LED
2. Power 2 LED
3. Power 3 LED
4. Ring Master LED
5. Ring status LED
6. Fault LED
7. Console port
8. Reset button
9. LAN port
10. Full duplex LED
11. LNK/ACT LED LAN ports
12. LAN port (Gigabit port for IES-3062GT/LAN port for IES-3080)
13. LNK/ACT LED (for G1 and G2 of IES-3062GT or P7 and P8 for IES-3080)

IES-3080 / IES-3062 Series User Manual
ORing Industrial Networking Corp
9
IES-3062FX & IES-3062GFX
1. Power 1 LED
2. Power 2 LED
3. Power 3 LED
4. Ring Master LED
5. Ring status LED
6. Fault LED
7. Console port
8. Reset button
9. LAN port
10. Full duplex LED
11. LNK/ACT LED LAN ports
12. Fiber port (Gigabit fiber port for IES-3062GFX/fiber port for IES-3062FX)
13. LNK/ACT LED (for G1 and G2 of IES-3062 GFX or P7 and P8 for IES-3062FX)

IES-3080 / IES-3062 Series User Manual
ORing Industrial Networking Corp
10
2.2 Front Panel LEDs
LED
Color
Status
Description
PW1
Green
On
DC power on
PW2
Green
On
DC power module 1 activated
PW3
Green
On
DC power module 2 activated
R.M
Green
On
Port running as O-Ring Master.
Ring
Green
On
O-Ring enabled.
Slowly blinking
Ring structure is broken (i.e. part of
the ring is disconnected)
Fast blinking
Faulty relay (power failure or port
malfunctioning)
Fault
Amber
On
DC power on
10/100Base-T(X) Fast Ethernet ports
LNK / ACT
Green
On
Ports are linked
Blinking
Transmitting data
Full Duplex
Amber
On
Ports running in full duplex mode
Gigabit Ethernet ports
ACT
Green
On
Ports are linked
Blinking
Transmitting data
LNK
Amber
On
Ports are linked
Fiber ports
ACT
Green
On
Ports are linked
Blinking
Transmitting data
LNK
Amber
On
Ports are linked
2.3 Top Panel
Below are the top panel components of IES-3000 series:
1. Terminal block
2. Ground wire

IES-3080 / IES-3062 Series User Manual
ORing Industrial Networking Corp
11
2.4 Rear Panel
On the rear panel of the switch sit three sets of screw holes. The two sets placed in
triangular patterns on both ends of the rear panel are used for wall-mounting (red boxes in the
figure below) and the set of four holes in the middle are used for Din-rail installation (blue box
in the figure below). For more information on installation, please refer to 3.1 Din-rail
Installation.
1. Wall-mount screw holes
2. Din-rail screw holes

IES-3080 / IES-3062 Series User Manual
ORing Industrial Networking Corp
12
Hardware Installation
3.1 DIN-rail Installation
The device comes with a DIN-rail kit with which you can fasten the switch to a DIN-rail in any
environments.
Din-rail Kit Measurement
Installing the switch on the DIN-rail is easy. First, screw the Din-rail kit onto the back of the
switch, right in the middle of the back panel. Then slide the switch onto a DIN-rail from the
Din-rail kit and make sure the switch clicks into the rail firmly.

IES-3080 / IES-3062 Series User Manual
ORing Industrial Networking Corp
13
3.2 Wall Mounting
Besides Din-Rail, the switch can be fixed to the wall via a wall mount panel, which can be
found in the package.
Wall-Mount Kit Measurement
To mount the switch onto the wall, follow the steps:
1. Screw the two pieces of wall-mount kits onto both ends of the rear panel of the switch. A
total of six screws are required, as shown below.
2. Use the switch, with wall mount plates attached, as a guide to mark the correct locations of
the four screws.
3. Insert screws through the round screw holes (the red arrow as below) on the sides or
through the cross-shaped aperture (the green arrow as below) in the middle of the plate and

IES-3080 / IES-3062 Series User Manual
ORing Industrial Networking Corp
14
fasten the screw to the wall with a screwdriver.
4. If the screw goes through the cross-shaped aperture, slide the switch down before
tightening the screw.
Note: Instead of screwing the screws in all the way, leave about 2 mm to allow room
for sliding the wall mount panel between the wall and the screws.
3.3 Wiring
ATTENTION
1. Be sure to disconnect the power cord before installing and/or wiring your
switches.
2. Calculate the maximum possible current in each power wire and
common wire. Observe all electrical codes dictating the maximum
current allowable for each wire size.
3. If the current goes above the maximum ratings, the wiring could
overheat, causing serious damage to your equipment.
4. Use separate paths to route wiring for power and devices. If power wiring
and device wiring paths must cross, make sure the wires are
perpendicular at the intersection point.
5. Do not run signal or communications wiring and power wiring through the
same wire conduit. To avoid interference, wires with different signal
characteristics should be routed separately.
6. You can use the type of signal transmitted through a wire to determine
which wires should be kept separate. The rule of thumb is that wiring
sharing similar electrical characteristics can be bundled together
7. You should separate input wiring from output wiring
8. It is advised to label the wiring to all devices in the system
WARNING
Do not disconnect modules or wires unless power has been switched off or
the area is known to be non-hazardous. The devices may only be connected
to the supply voltage shown on the type plate.

IES-3080 / IES-3062 Series User Manual
ORing Industrial Networking Corp
15
3.3.1 Grounding
Grounding and wire routing help limit the effects of noise due to electromagnetic interference
(EMI). Run the ground connection from the ground screw on the power module to the
grounding surface prior to connecting devices.
3.3.2 Redundant Power Inputs
The switch has two sets of power inputs, power input 1 and power input 2, which sit on the
front panel along with LAN ports. Follow the steps below to wire redundant power inputs.
Step 1: insert the negative/positive wires into the V-/V+ terminals, respectively.
Step 2: to keep the wires from pulling loose, use a small flat-blade screwdriver to tighten the
wire-clamp screws on the front of the terminal block connector.
3.4 Connection
3.4.1 Cables
The IES-3000 series switches have standard Ethernet ports. According to the link type, the
switch uses CAT 3, 4, 5,5e UTP cables to connect to any other network devices (PCs, servers,
switches, routers, or hubs). Please refer to the following table for cable specifications.
Cable Types and Specifications
Cable
Type
Max. Length
Connector
10BASE-T
Cat.3, 4, 5 100-ohm
UTP 100 m (328ft)
RJ-45
100BASE-TX
Cat.5 100-ohm UTP
UTP 100 m (328ft)
RJ-45
1000BASE-TX
Cat.5/Cat.5e 100-ohm UTP
UTP 100 m (328ft)
RJ-45
10/100/1000BASE-T(X) Pin Assignments
With 10/100/1000BASE-T(X) cables, pins 1 and 2 are used for transmitting data, and pins 3
and 6 are used for receiving data.
RJ-45 pin assignments
Pin Number
Assignment
1
TD+
2
TD-
3
RD+
4
Not used
5
Not used

IES-3080 / IES-3062 Series User Manual
ORing Industrial Networking Corp
16
6
RD-
7
Not used
8
Not used
The IES-3000 series switches support auto MDI/MDI-X operation. You can use a cable to
connect the switch to a PC. The table below shows the 10/100BASE-TX and 1000Base-T MDI
and MDI-X port pin outs.
10/100 Base-TX MDI/MDI-X pins assignments
Pin Number
MDI port
MDI-X port
1
TD+(transmit)
RD+(receive)
2
TD-(transmit)
RD-(receive)
3
RD+(receive)
TD+(transmit)
4
Not used
Not used
5
Not used
Not used
6
RD-(receive)
TD-(transmit)
7
Not used
Not used
8
Not used
Not used
Note: “+” and “-” signs represent the polarity of the wires that make up each wire pair.
1000 Base-T MDI/MDI-X pins assignments
Pin Number
MDI port
MDI-X port
1
BI_DA+
BI_DB+
2
BI_DA-
BI_DB-
3
BI_DB+
BI_DA+
4
BI_DC+
BI_DD+
5
BI_DC-
BI_DD-
6
BI_DB-
BI_DA-
7
BI_DD+
BI_DC+
8
BI_DD-
BI_DC-
Note: “+” and “-” signs represent the polarity of the wires that make up each wire pair.
RS-232 Console Port Wiring
The IES-3000 series switches can be managed via console ports using a RS-232 cable which
can be found in the package. You can connect the port to a PC via the RS-232 cable with a
DB-9 female connector. The DB-9 female connector of the RS-232 cable should be connected
the PC while the other end of the cable (RJ-45 connector) should be connected to the console

IES-3080 / IES-3062 Series User Manual
ORing Industrial Networking Corp
17
port of the switch.
PC pin out (male) assignment
RS-232 with DB9 female connector
DB9 to RJ 45
Pin #2 RD
Pin #2 TD
Pin #2
Pin #3 TD
Pin #3 RD
Pin #3
Pin #5 GD
Pin #5 GD
Pin #5
3.4.2 O-Ring/O-Chain
O-Ring
You can connect three or more switches to form a ring topology to gain network redundancy
capabilities through the following steps.
1. Connect each switch to form a daisy chain using an Ethernet cable.
2. Set one of the connected switches to be the master and make sure the port setting of each
connected switch on the management page corresponds to the physical ports connected. For
infomration about the port setting, please refer to 4.1.2 Configurations.
3. Connect the last switch to the first switch to form a ring topology.
Coupling Ring
If you already have two O-Ring topologies and would like to connect the rings, you can form
them into a couping ring. All you need to do is select two switches from each ring to be
connected, for example, switch A and B from Ring 1 and switch C and D from ring 2. Decide

IES-3080 / IES-3062 Series User Manual
ORing Industrial Networking Corp
18
which port on each switch to be used as the coupling port and then link them together, for
example, port 1 of switch A to port 2 of switch C and port 1 of switch B to port 2 of switch D.
Then, enable Coupling Ring option by checking the checkbox on the management page and
select the coupling ring in correspondance to the connected port. For more inforamtion on port
setting, please refer to 4.1.2 Configurations. Once the setting is completed, one of the
connections will act as the main path while the other will act as the backup path.
Dual Homing
If you want to connect your ring topology to a RSTP network environment, you can use dual
homing. Choose two switches (Switch A & B) from the ring for connecting to the switches in the
RSTP network (core switches). The connection of one of the switches (Switch A or B) will act
as the primary path, while the other will act as the backup path that is activated when the
primary path connection fails.

IES-3080 / IES-3062 Series User Manual
ORing Industrial Networking Corp
19
O-Chain
When connecting multiple O-Rings to meet your expansion demand, you can create an
O-Chain topology through the following steps.
1. Select two switches from the chain (Switch A & B) that you want to connect to the O-Ring
and connect them to the switches in the ring (Switch C & D).
2. In correspondence to the port connected to the ring, configure an edge port for both of the
connected switches in the chain by checking the box in the management page (see 4.1.2
Configurations).
3. Once the setting is completed, one of the connections will act as the main path, and the
ohter as the back up path.