ORiNG IAR-620 User manual

Features
High Speed Air Connectivity: WLAN interface support up to 300Mbps
link speed
Provide HNAT enhance LAN to WAN routing performance
Highly Security Capability: WEP/WPA/WPA-PSK(TKIP,AES)/
WPA2/WPA2-PSK(TKIP,AES)/802.1X Authentication supported
Secured Management by HTTPs
Support STP(802.1D) for wireless redundancy
Various kind of WAN Connection Type supported: Dynamic/Static IP,
PPPoE, Modem Dial Up
IP table to prevent access from unauthorized IP address
Support VPN for secured network connection (Open VPN, PPTP VPN)
Support NAT Setting (Virtual Server, Port Trigger, DMZ, UPnP)
Support DHCP forwarder through PPTP function)
Cellular Modem signal information display (un-connecting status)
Wireless connecting status monitoring
USB interface support 3.5G HSDPA USB Modem dial up
1KV isolation for PoE P.D. port of IAR-620+
Event Warning by Syslog, Email, SNMP Trap, Relay output and Beeper
Rigid IP-30 housing design
DIN-Rail and Wall-mount enabled
IAR-620 / IAR-620+
IAR-620
IAR-620 / IAR-620+
is a reliable IEEE 802.11 a/b/g/n WLAN VPN router
with 2 ports 10/100Base-T(X) where ETH1 for LAN and ETH2 for WAN. It
supports 802.1X and MAC filter for security control. It could be
configured to operate in 3 modes of routing function: Dynamic/Static IP
route, PPPoE authentication, and Modem (56K/GPRS/3G/3.5G Modem)
dial up. In the mode of Modem dial up, it support both traditional 56K
modem and GPRS/3G/3.5G Modem with USB interface. Users can set
up WLAN environment to fulfill demands of various applications rapidly
by dialing up cellular modems. In addition, + also provides P.D.
feature on ETH2 which is fully compliant with IEEE802.3af PoE P.D.
specification. This feature extends the layout up to 100 meter without
additional power lines. Therefore, is one of the best
solution for applications of wireless communication.
Introduction
QIG
Version 1.0
Quick Installation Guide
ORing Industrial Networking Corp.
Quick Installation Guide
IAR-620 Series
Wireless
IAR-620 Series
Industrial Wireless LAN Access
Point Router
ACCESS POINT Router
INDUSTRIAL
1907-2-29-IAR620-0
Specifications
ORing WLAN Access Point
Model IAR-620
Physical Ports
WLAN Interface
Power Indicator
Faul t Red for Ethernet link down or power down indicator
10/100Base-T(X) RJ45 port
indicator Green for port Link/Act at 100Mbps. Amber for port Link/Act at 10Mbps.
Power
Redundant Input power
Power consumption(Typ.)
Dual DC inputs. 12~48VDC on 6-pin terminal block
6 Watts
Overload current protection
Reversepolarityprotection Present
Present
Physical Characteristic
Enclosure IP-30
Dimension(WxDxH) 54.1(W)x106.1(D)x145.4(H)mm(2.13x4.18x5.72inch.)
Weig ht (g ) 803 g
Environmental
-40to85C(-40to185 F)
oo
Storage Temperature
10/100Base-T(X) Ports in RJ45
Auto MDI/MDIX 2
LED Indicators
Static/Dynamic IP, PPPoE, Modem (56K/GPRS/3G/3.5G Modem) dial up
WAN Connection Type
IEEE802.11a/n: OFDM with BPSK, QPSK, 16QAM, 64QAM
IEEE802.11b: CCK, DQPSK, DBPSK
IEEE802.11g/n: OFDM with BPSK, QPSK, 16QAM, 64QAM
Modulation
802.11b: 1/2/5.5/11 Mbps;
802.11a/g: 6/9/12/18/24/36/48/54 Mbps
802.11n(40MHz): UP to 300 Mbps
Transmission Rate
802.11a: 13dBm 1.5dBm
802.11b: 16dBm 1.5dBm
802.11g: 14dBm 1.5dBm
802.11n(2.4G@20MHz): 13dBm 1.5dBm
802.11n(2.4G@40MHz): 12dBm 1.5dBm
802.11n(5G@20MHz): 12dBm 1.5dBm
802.11n(5G@40MHz): 12dBm 1.5dBm
±
±
±
±
±
±
±
Transmit Power
802.11a: -68dBm 2dBm@54Mbps
802.11b: -82dBm 2dBm@11Mbps
802.11g: -68dBm 2dBm@54Mbps
802.11n(2.4G@20MHz, MCS15): -64dBm 2dBm
802.11n(2.4G@40MHz, MCS15): -60dBm 2dBm
802.11n(5G@20MHz, MCS15): -64dBm 2dBm
802.11n(5G@40MHz, MCs15): -60dBm 2dBm
±
±
±
±
±
±
±
Receiver Sensitivity
ReverseSMAx2
Antenna Connector
America/FCC:
2.412~2.462 GHz (11 channels)
5.180~5.240 GHz & 5.745~5.825 GHz (9 channels)
Europe CE/ETSI:
2.412~2.472 GHz (13 channels)
5.180~5.240 GHz (4 channels)
Japan(JP):
2.412~2.484 GHz (13 Channels)
5.180~5.240 GHz (4 channels)
Canada(CA):
2.412~2.462 GHz (11 channels)
5.180~5.825 GHz ( 21 channels )
Frequency Band
SSID broadcast disable
WEP: (64-bit ,128-bit key supported)
WPA/WPA2 :802.11i(WEP and AES encryption)
WPA-PSK (256-bit key pre-shared key supported)
802.1X Authentication supported
TKIP encryption
Encryption Security
Wireless Security
IAR-620+
PoE P.D Port
Present at ETH2
Fully compliant with IEEE 802.3af Power
Device specification
Over load & short circuit protection
Isolation Voltage: 1000 VDC min.
Isolation Resistance: 10 ohms min
8
USB modems and ISDN adapters which support the Communication Device Class Abstract Control Model interface
List of tested device :
1. Hummingbird huc56s (Conexant)
2. Huawei E220/E230
3. Simense HSDPA-180C
4. Prolific 2303 + serial modem
5. Quanta MUQ101
6. Sony Ericsson MD400/MD400g
7. Sierra C885
List
Modem Support
WLAN LED WLAN Link /ACT: Green: Link, Orange : Poor signal
Green for WLAN Strength: 1<25%, 2<50%, 3<75%, 4<100%
807 g
-10to60C(-14to140 F)
oo
Operating Temperature
5% to 95% Non-condensing
Operating Humidity
Regulatory Approvals
FCC Part 15, CISPR (EN55022) class A
EMI
EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN1000-4-6(CS),
EN61000-4-8, EN61000-4-11
EMS
IEC60068-2-27
Shock
IEC60068-2-32
IEC60068-2-6
Vibration
EN60950-1
Safety
Free Fall
Warranty
3years
Fault Contact
Relay Relayoutputtocarrycapacityof1Aat24VDC
PWR 1(2)(PoE) / Ready:
Red On: Power is on and booting up.
GreenOn:PowerisonandfunctioningNormally.
Installation
DIN-Rail Install Step Wall-mounted Install Step
ORing Industrial Networking Corp.
Copyright© 2012 ORing
All rights reserved.
TEL: [phone]
FAX: [phone]
Website: www.oring-networking.com
E-mail: [email protected]
PRINTED ON RECYCLED PAPER
1x USB 2.0 Host port
USB Host port
DSSS
Radio Frequency Type

IAR-620+IAR-620
Front Panel
Packing list
Accessory
Ethernet Port 1
Ethernet Port 2
Wireless LAN LED
Wall-mounted kit DIN-Rail kit
1
6-Pin Terminal block
2
4
Screw (M3 X5)
3
Dust Cover
5CD
6
QIG
7
Industrial IEEE 802.11 a b g n Cellular VPN router
with x Base T X US band
///
2 10/100 - ( ),
IAR-620_US
Model name Description Accessory
100M LNK/ACT LED
(Green)
10M LNK/ACT LED
(Amber)
Quick Installation Guide
ORing Industrial Networking Corp.
Front Panel
A
B
IAR-620_EU
IAR-620_JP
IAR-620_CA
1X1, 2X1, 3X6,
5X2, 6X1, 7X1,
4X1,
8X2
Quick Installation Guide
IAR-620/620+
WLAN
Fault
PWR2
PWR1
ANT.1
ETH1
ETH2
WLAN
Fault
PWR2
PWR1
ANT.1
ETH1
ETH2
P.O.E.
P.O.E.
BA
WLAN Antenna
8
PRINTED ON RECYCLED PAPER
QIG
WLAN Antenna
Power 1 LED
Power 2 LED
Fault LED
ANT.2
WLAN Strength LED
ANT.2
Wireless
INDUSTRIAL
Power Connection Guide
Reset
PWR-2 PWR-1
V2+ V2- Relay V1+ V1-
Reset Button
Terminal Block Power-2 Input
Relay Output Pin
Terminal Block Power-1 Input
Applications
In IAR-620/IAR-620+, there are 3 modes of routing functions supported:
Dynamic/ Static IP route, PPPoE dial up, and Modem dial up. IAR-620/IAR-
620+ also support NAT, VPN and Back up functions. You can build up the
wireless network and connect to the Internet easily.
1X1, 2X1, 3X6,
5X2, 6X1, 7X1,
4X1,
8X2
1X1, 2X1, 3X6,
5X2, 6X1, 7X1,
4X1,
8X2
1X1, 2X1, 3X6,
5X2, 6X1, 7X1,
4X1,
8X2
1X1, 2X1, 3X6,
5X2, 6X1, 7X1,
4X1,
8X2
1X1, 2X1, 3X6,
5X2, 6X1, 7X1,
4X1,
8X2
1X1, 2X1, 3X6,
5X2, 6X1, 7X1,
4X1,
8X2
1X1, 2X1, 3X6,
5X2, 6X1, 7X1,
4X1,
8X2
Industrial IEEE 802.11 a b g n Cellular VPN router
with 2x10/100Base-T(X), EU band
///
Industrial IEEE 802.11 a b g n Cellular VPN router
with 2x10/100Base-T(X), JP band
///
Industrial IEEE 802.11 a b g n Cellular VPN router
with 2x10/100Base-T(X), CA band
///
A
A
A
IAR-620+_US
IAR-620+_EU
IAR-620+_JP
IAR-620+_CA
B
B
B
Iindustrial IEEE 802.11 a b g n Cellular VPN router
with x Base T X port PoE P D US band
///
2 10/100 - ( ), 1- . .,
Iindustrial IEEE 802.11 a b g n Cellular VPN router
with x Base T X port PoE P D band
///
2 10/100 - ( ), 1- . ., EU
Iindustrial IEEE 802.11 a b g n Cellular VPN router
with x Base T X port PoE P D JP band
///
2 10/100 - ( ), 1- . .,
Iindustrial IEEE 802.11 a b g n Cellular VPN router
with x Base T X port PoE P D band
///
2 10/100 - ( ), 1- . ., CA
IAR-620 Series
IAR-620 Series
Industrial Wireless LAN Access
Point Router
ACCESS POINT Router
IAR-620/IAR-620+ can also be configure through ORing’s Windows utility
Open-Vision
Step 1: Open the commander and click ”Discover”, the AP devices will
show on the list.
Step 2: Choose your access point, and it will show the AP function tree.
Simultaneity, you can login and then set the AP.
Open-Vision
USB
Modem
USB
USB
Modem
USB
PoE LED
USB Port
USB LED
Ethernet Port 2
/ PoE P.D. Port