ORiNG TES-3082GT-M12-BP1 User manual

T
TE ES S- -3 30 08 82 2G GT T- -M M1 12 2- -B BP P1 1
I
In nd du us st tr ri ia al l M Ma an na ag ge ed d E Et th he er rn ne et t S Sw wi it tc ch h
E
EN N5 50 01 15 55 5 S Se er ri ie es s
U
Us se er r’ ’s s M Ma an nu ua al l
V
Ve er rs si io on n 1 1. .0 0
A
Ap pr ri il l, , 2 20 01 13 3
w
ww ww w. .o or ri in ng g- -n ne et tw wo or rk ki in ng g. .c co om m

TES-3082GT-M12-BP1 User’s Manual
ORing Industrial Networking Corp 1
COPYRIGHT NOTICE
Copyright © 2010 ORing Industrial Networking Corp.
All rights reserved.
No part of this publication may be reproduced in any form without the prior written
consent of ORing Industrial Networking Corp.
TRADEMARKS
is a registered trademark of ORing Industrial Networking Corp.
All other trademarks belong to their respective owners.
REGULATORY COMPLIANCE STATEMENT
Product(s) associated with this publication complies/comply with all applicable
regulations. Please refer to the Technical Specifications section for more details.
WARRANTY
ORing warrants that all ORing products are free from defects in material and
workmanship for a specified warranty period from the invoice date (5 years for most
products). ORing will repair or replace products found by ORing to be defective
within this warranty period, with shipment expenses apportioned by ORing and the
distributor. This warranty does not cover product modifications or repairs done by
persons other than ORing-approved personnel, and this warranty does not apply to
ORing products that are misused, abused, improperly installed, or damaged by
accidents.
Please refer to the Technical Specifications section for the actual warranty period(s)
of the product(s) associated with this publication.
DISCLAIMER
Information in this publication is intended to be accurate. ORing shall not be
responsible for its use or infringements on third-parties as a result of its use. There
may occasionally be unintentional errors on this publication. ORing reserves the
right to revise the contents of this publication without notice.
CONTACT INFORMATION
ORing Industrial Networking Corp.
3F., NO.542-2, Jhongjheng Rd., Sindian District, New Taipei City 23145, Taiwan,
R.O.C.
Tel: + 886 2 2218 1066 // Fax: + 886 2 2218 1014
Website: www.oring-networking.com

TES-3082GT-M12-BP1 User’s Manual
ORing Industrial Networking Corp 2
Technical Support
E-mail: [email protected]
Sales Contact
E-mail: [email protected] (Headquarters)
[email protected] (China)

Table of Content
Getting to Know Your Switch...............................................................3
1.1About the TES-3082GT-M12-BP1 Managed Industrial Switch.......................3
1.2Software Features...........................................................................................................4
1.3Hardware Features.........................................................................................................4
Hardware Installation.............................................................................5
2.1Wall Mounting Installation...........................................................................................5
Hardware Overview .................................................................................0
3.1Front Panel........................................................................................................................0
3.2Front Panel LEDs.............................................................................................................2
3.3Hardware Bypass............................................................................................................3
Cables............................................................................................................4
4.1Ethernet Cables...............................................................................................................4
4.1.1100BASE-TX/10BASE-T Pin Assignments.....................................................4
4.2Console Cable...................................................................................................................6
WEB Management ....................................................................................7
5.1Configuration by Web Browser..................................................................................7
5.1.1About Web-based Management.......................................................................7
5.1.2System Information..............................................................................................9
5.1.3Front Panel...............................................................................................................9
5.1.4Basic setting..........................................................................................................10
5.1.4.1Switch Setting..................................................................................................10
5.1.4.2Admin Password..............................................................................................10
5.1.4.3IP Setting...........................................................................................................11
5.1.4.4Time Setting.....................................................................................................12
5.1.4.5LLDP.....................................................................................................................16
5.1.4.6Modbus TCP......................................................................................................16
5.1.4.7Auto Provision..................................................................................................17
5.1.4.8Backup & Restore...........................................................................................17
5.1.4.9Upgrade Firmware..........................................................................................19
5.1.5Redundancy...........................................................................................................19

TES-3082GT-M12-BP1 User’s Manual
ORing Industrial Networking Corp 1
5.1.5.1MRP......................................................................................................................19
5.1.5.2O-Ring.................................................................................................................20
5.1.5.3OPEN-Ring.........................................................................................................22
5.1.5.4O-Chain..............................................................................................................23
5.1.5.5RSTP – Repeater.............................................................................................24
5.1.5.6Fast Recovery...................................................................................................24
5.1.5.7RSTP....................................................................................................................25
5.1.5.8MSTP ...................................................................................................................28
5.1.6Multicast..................................................................................................................33
5.1.6.1IGMP Snooping................................................................................................33
5.1.6.2MVR......................................................................................................................34
5.1.6.3Static Multicast Filtering ..............................................................................35
5.1.7Port Setting............................................................................................................36
5.1.7.1Port Control.......................................................................................................36
5.1.7.2Port Status ........................................................................................................37
5.1.7.3Port Alias............................................................................................................37
5.1.7.4Rate Limit..........................................................................................................37
5.1.7.5Port Trunk..........................................................................................................38
5.1.7.6Loop Guard.......................................................................................................40
5.1.8VLAN.........................................................................................................................40
5.1.8.1VLAN Setting - IEEE 802.1Q......................................................................40
5.1.8.2VLAN Setting – Port Based.........................................................................42
5.1.9Traffic Prioritization.............................................................................................44
5.1.9.1Qos policy..........................................................................................................44
5.1.9.2Port-base priority............................................................................................45
5.1.9.3COS/802.1p......................................................................................................46
5.1.9.4TOS/DSCP .........................................................................................................47
5.1.10DHCP Server / Relay..........................................................................................47
5.1.10.1DHCP Server – Setting...............................................................................47
5.1.10.2DHCP Server – Client List.........................................................................48
5.1.10.3DHCP Server – Port and IP bindings.....................................................49
5.1.10.4DHCP Server –DHCP Relay Agent..........................................................49
5.1.11SNMP........................................................................................................................51
5.1.11.1SNMP – Agent Setting................................................................................51
5.1.11.2SNMP –Trap Setting.....................................................................................52
5.1.11.3SNMPV3...........................................................................................................53
5.1.12Security...................................................................................................................55

TES-3082GT-M12-BP1 User’s Manual
ORing Industrial Networking Corp 2
5.1.12.1Management Security................................................................................55
5.1.12.2Static MAC Forwarding...............................................................................56
5.1.12.3MAC Blacklist.................................................................................................57
5.1.12.4802.1x..............................................................................................................57
5.1.12.5IP Guard..........................................................................................................60
5.1.13Warning...................................................................................................................63
5.1.14Monitor and Diag.................................................................................................67
5.1.14.1System Event Log........................................................................................67
5.1.14.2MAC Address Table......................................................................................68
5.1.14.3Port Overview................................................................................................69
5.1.14.4Port Counters.................................................................................................70
5.1.14.5Port Monitoring .............................................................................................72
5.1.14.6Traffic Monitor ...............................................................................................73
5.1.14.7Ping ...................................................................................................................74
5.1.15Save Configuration .............................................................................................75
5.1.16Factory Default.....................................................................................................75
5.1.17System Reboot.....................................................................................................75
Command Line Interface Management ..........................................76
6.1About CLI Management.........................................................................................76
6.2Commands Set List—System Commands Set...............................................81
6.3Commands Set List—Port Commands Set......................................................84
6.4Commands Set List—Trunk command set......................................................87
6.5Commands Set List—VLAN command set.......................................................88
6.6Commands Set List—Spanning Tree command set.....................................89
6.7Commands Set List—QoS command set.........................................................92
6.8Commands Set List—IGMP command set.......................................................93
6.9Commands Set List—MAC/Filter Table command set.................................93
6.10Commands Set List—SNMP command set......................................................94
6.11Commands Set List—Port Mirroring command set......................................95
6.12Commands Set List—802.1x command set...................................................96
6.13Commands Set List—TFTP command set........................................................98
6.14Commands Set List—SYSLOG, SMTP, EVENT command set....................99
6.15Commands Set List—SNTP command set.....................................................101
6.16Commands Set List—O-Ring command set.................................................102
Technical Specifications.........................................................................0

TES-3082GT-M12-BP1 User’s Manual
ORing Industrial Networking Corp 3
Getting to Know Your Switch
1.1 About the TES-3082GT-M12-BP1
Managed Industrial Switch
ORing’s TransporterTM series managed Ethernet switches are designed for industrial
applications, such as rolling stock, vehicle, and railway applications. The
TES-3082GT-M12-BP1 is a managed Redundant Ring Ethernet switch with
8x10/100Base-T(X) and 2x10/100/1000Base-T(X) ports which is specifically
designed for the toughest and fully compliant with EN50155 requirement. With
completely support of Ethernet Redundancy protocol, O-Ring (recovery time <
10ms over 250 units of connection), Open-Ring, O-Chain, MRP and MSTP/RSTP/STP
(IEEE 802.1s/w/D) can protect your mission-critical applications from network
interruptions or temporary malfunctions with its fast recovery technology. Another
Open-Ring technology is also supported which can applied for other vendor's
proprietary ring. TES-3082GT-M12-BP1 EN50155 Ethernet switch use M12
connectors to ensure tight, robust connections, and guarantee reliable operation
against environmental disturbances, such as vibration and shock.
TES-3082GT-M12-BP1 can be managed centralized and convenient by a powerful
windows utility ~ Open-Vision. In addition, the wide operating temperature range
from -40oC to 70oC can satisfy most of operating environment. Therefore, the
switch is one of the most reliable choices for rolling stock and highly-managed
Ethernet application.

TES-3082GT-M12-BP1 User’s Manual
ORing Industrial Networking Corp 4
1.2 Software Features
World’s fastest Redundant Ethernet Ring : O-Ring (Recovery time < 10ms over
250 units connection)
Supports Ring Coupling, Dual Homing over O-Ring
Supports SNMPv1/v2/v3 & RMON & Port base/802.1Q VLAN Network
Management
Event notification by Email, SNMP trap and Relay Output
Web-based ,Telnet, Console (CLI) configuration
DHCP assign each Equipment IP by each Port
Link Layer Discovery Protocol(LLDP)
Port based network access control (802.1x)
VLAN (802.1Q ) to segregate and secure network traffic
Radius centralized password management
SNMP v1/v2c/v3 support for secured network management
STP/RSTP/MSTP supported
Quality of Service (802.1p) for real-time traffic
VLAN (802.1Q) with double tagging and GVRP supported
IGMP v2/v3 (IGMP snooping support) for filtering multicast traffic
PTP Client (Precision Time Protocol) clock synchronization
Port configuration, status, statistics, mirroring, security
Remote Monitoring (RMON)
1.3 Hardware Features
Leading EN50155-compliant Ethernet switch for rolling stock application
Redundant two DC power inputs
Wide Operating Temperature: -40 to 70oC
Storage Temperature: -40 to 85oC
Operating Humidity: 5% to 95%, non-condensing
Casing: IP-40
8 x 10/100 Base-T(X) Ports in M12 ,Auto MDI/MDIX
2 x 10/100/1000Base-T(X) ports in M12
Console Port (RS-232 in M12 connector (A-coding) )
Dimensions(W x D x H) :170 (W) x 75 (D) x196 (H) mm
Wall mounting enabled

TES-3082GT-M12-BP1 User’s Manual
ORing Industrial Networking Corp 5
Hardware Installation
2.1 Wall Mounting Installation
Each switch has another installation method for users to fix the switch. A wall
mount panel can be found in the package. The following steps show how to
mount the switch on the wall:

TES-3082GT-M12-BP1 User’s Manual
ORing Industrial Networking Corp 6
Wall-Mounting size

Hardware Overview
3.1 Front Panel
The following table describes the labels that stick on the TES-3082GT-M12-BP1.
Port Description
10/100 M12 fast
Ethernet ports
8 10/100Base-T(X) M12 (D-coding) fast Ethernet ports
support auto-negotiation.
Default Setting :
Speed: auto
Duplex: auto
Flow control : disable
Gigabit M12 ports 2 10/100/1000Base-T(X) Gigabit ports(use two M12 Port)
Console Use RS-232 to M12 (A-Coding) connecter to manage
switch.
Reset Push reset button 2 to 3 seconds to reset the switch.
Push reset button 5 seconds to reset the switch into
Factory Default.

TES-3082GT-M12-BP1 User’s Manual
ORing Industrial Networking Corp 1
TES-3082GT-M12-BP1
1. Switch Status LED
LED for PWR1. When the PWR1 links, the green led will be light on.
LED for PWR2. When the PWR2 links, the green led will be light on.
LED for R.M (Ring master). When the LED light on, it means that the switch
is the ring master of O-Ring.
LED for Ring. When the LED light on, it means the O-Ring is activated.
LED for Fault Relay. When the fault occurs, the amber LED will be light on.
Reset button. Push the button 3 seconds for reset; 5 seconds for factory
default.
2. Relay Port
3. Console port (M12 to Series)
4. Power Input ( M23 connect )
5. 10/100Base-T(X) Ethernet ports.
6. Port LED Status
Green LED for Ethernet ports LNK/ACT status
Amber LED for Packet Duplex/Collision status
7. 10/100/1000Base-T(X) ports in M12(G1A←Bypass→G2A, G1B←Bypass→G2B)

TES-3082GT-M12-BP1 User’s Manual
ORing Industrial Networking Corp 2
3.2 Front Panel LEDs
LED Color Status Description
PW1 Green On DC power module 1
activated.
PW2 Green On DC power module 2
activated.
R.M Green On O-Ring Master active.
Ring Green
On O-Ring enabled.
Slowly blinking O-Ring topology has
problem
Fast blinking O-Ring work normally.
Fault Amber On Fault relay. Power failure
or Port down/fail indicator.
10/100Base-T(X) Fast Ethernet ports
LNK/ACT Green On Port link up.
Blinking Data transmitted.
Full
Duplex Green On Port works under full duplex.
Collision Green On Packet Collision
Gigabit Ethernet ports
LNK/ACT Green On Port link up.
Blinking Data transmitted.
100M Green On Port link to 100M.

TES-3082GT-M12-BP1 User’s Manual
ORing Industrial Networking Corp 3
3.3 Hardware Bypass
Let ORing introduce the natural yet critically important network redundancy –
Hardware Bypass, which effectively avoids single-point power failure in daisy chain
topology or multi-point power failures in ring topology. For conventional wired
Ethernet network, there is the Cooper Interface Bypass. An ORing Ethernet switch
with Cooper Interface Bypass would have 2 of the Ethernet ports designated as the
bypass path. Under normal circumstances, these ports would function just like any
other port. However, when power failure occurs, the internal bypass circuit connects
these 2 ports together, effectively letting the network ride through this Ethernet
switch that has lost power to operate. An example of an ORing switch with Cooper
Interface Bypass is TES-3080-M12-BP2.

TES-3082GT-M12-BP1 User’s Manual
ORing Industrial Networking Corp 4
Cables
4.1 Ethernet Cables
The TES-3082GT-M12-BP1 switch had standard Ethernet ports. According to the
link type, the switches use CAT 3, 4, 5, 5e UTP cables to connect to any other
network device (PCs, servers, switches, routers, or hubs). Please refer to the
following table for cable specifications.
Cable Types and Specifications
Cable Type Max. Length Connector
10BASE-T Cat.3, 4, 5 100-ohm UTP 100 m (328 ft)
M12(D-Coding)
100BASE-TX Cat.5 100-ohm UTP UTP 100 m (328 ft)
M12(D-Coding)
1000BASE-TX Cat.5/Cat.5e 100-ohm
UTP UTP 100 m (328ft)
G1A+G1B
G2A+G2B
User to M12
Port
4.1.1 100BASE-TX/10BASE-T Pin Assignments
With 100BASE-TX/10BASE-T cable, pins 1 and 3 are used for transmitting data,
and pins 2 and 4 are used for receiving data.
Pin Number Assignment
1 Tx +
2 Rx -
3 Tx -
4 Rx +

TES-3082GT-M12-BP1 User’s Manual
ORing Industrial Networking Corp 5
1000 Base-T RJ-45 Pin Assignments
Pin Number Assignment
Giga A - 1 BI_DA+
Giga A - 2 BI_DA-
Giga A - 3 BI_DB+
Giga B -1 BI_DC+
Giga B - 2 BI_DC-
Giga A - 6 BI_DB-
Giga B - 3 BI_DD+
Giga B - 6 BI_DD-
The TES-3082GT-M12-BP1 switch supports auto MDI/MDI-X operation. You
can use a straight-through cable to connect PC to switch. The following table
below shows the 10BASE-T/ 100BASE-TX MDI and MDI-X port pin outs.
10/100 Base-TX MDI/MDI-X pins assignment
Pin Number MDI port MDI-X port
1 TD+(transmit) RD+(receive)
2 TD-(transmit) RD-(receive)
3 RD+(receive) TD+(transmit)
4 Not used Not used
5 Not used Not used
6 RD-(receive) TD-(transmit)
7 Not used Not used
8 Not used Not used
1000 Base-T MDI/MDI-X pins assignment
Pin Number MDI port MDI-X port
Giga A - 1 BI_DA+ BI_DB+
Giga A - 2 BI_DA- BI_DB-
Giga A - 3 BI_DB+ BI_DA+
Giga B -1 BI_DC+ BI_DD+
Giga B - 2 BI_DC- BI_DD-
Giga A - 6 BI_DB- BI_DA-
Giga B - 3 BI_DD+ BI_DC+
Giga B - 6 BI_DD- BI_DC-
Note: “+” and “-” signs represent the polarity of the wires that make up each wire pair.

TES-3082GT-M12-BP1 User’s Manual
ORing Industrial Networking Corp 6
4.2 Console Cable
TES-3080-M12 switch can be management by console port. You can connect
them to PC via a RS-232 cable with DB-9 female connector and the other end (M12
connector) connects to console port of switch.

TES-3082GT-M12-BP1 User’s Manual
ORing Industrial Networking Corp 7
WEB Management
5.1 Configuration by Web Browser
This section introduces the configuration by Web browser.
5.1.1 About Web-based Management
An embedded HTML web site resides in flash memory on the CPU board. It
contains advanced management features and allows you to manage the switch from
anywhere on the network through a standard web browser such as Microsoft
Internet Explorer.
The Web-Based Management function supports Internet Explorer 5.0 or later. It
is based on Java Applets with an aim to reduce network bandwidth consumption,
enhance access speed and present an easy viewing screen.
Note: By default, IE5.0 or later version does not allow Java Applets to open sockets. You need to
explicitly modify the browser setting in order to enable Java Applets to use network ports.
Preparing for Web Management
The default value is as below:
IP Address: 192.168.10.1
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.10.254
User Name: admin
Password: admin
System Login
1. Launch the Internet Explorer.

TES-3082GT-M12-BP1 User’s Manual
ORing Industrial Networking Corp 8
2. Type http:// and the IP address of the switch. Press “Enter”.
3. The login screen appears.
4. Key in the username and password. The default username and password
is “admin”.
5. Click “Enter” or ”OK” button, then the main interface of the Web-based
management appears.
Login screen
Main Interface
Main interface

TES-3082GT-M12-BP1 User’s Manual
ORing Industrial Networking Corp 9
5.1.2 System Information
System Information interface
System Information
The system information will display the configuration of Basic Setting / Switch
Setting page.
Enable Location Alert
When click , PWR1, PWR2 and PWR3 LEDs of the switch
will start to flash together, and click , the LEDs will stop
flashing.
5.1.3 Front Panel
Show the panel of TES-3082GT-M12-BP1. Click “Close” to close panel on web.