Orion GST-2050 User manual

HD-SDI 3-AXIS DAY & NIGHT
IR DOME CAMERA
GST-2050
MANUAL
◐ HOW TO INSTALL
1. Opening the dome
2. Removing the dome
3. Camera installation
:
:
:
Pushing the latch button.(Remove the protection
sheet after installing.)
Lift the dome. When you push the latch
button, it is unlocked and you can lift the dome.
(1) Fix the camera set with the supplied screws on ceiling or wall mount.
If you don't use supplied screws, the camera may fall off.
(2) Please refer to '4. Camera angle adjustment' regarding adjust
camera angle.
(3) Lens adjustment(Vari-focal Lens only)
After opening the LED cover,
① By turning the "Tele-Wide" knob,
you can access a range of focal
lengths within specified limits.
② Since then, by turning the "Near-Far"
knob, you can set the focus toward
the wanted object.
(4) Re-assemble the camera.
<Ceiling mount>
4. Camera angle adjustment :
(1) Pan adjustment
(2) Tilt adjustment
(3) Roll adjustment
: Grasp the disk of camera and then adjust
direction to the right or left(-180 ~ 180 )
: Grasp the LED cover of camera and then adjust
direction to the up or down(6 ~ 90 )
: Grasp the camera holder and then rotate
(-178 ~ 178 )
˚ ˚
˚ ˚
˚ ˚
◐ DIMENSION
◐ ASSEMBLY
<Caution> If you try to adjust the camera out of limited angle, it might cause
troubles and damage to camera.
ROTATION
U
D
R
L
LED COVER
DISK
CAMERA HOLDER
SCREW TP1
3.5x20 2EA
SCREW TP1
3.5x20 2EA
<Wall mount>
DOME COVER
LED COVER
SCREW
CAMERA MODULE
SCREW
CABLE
DISK
BASE
CONTROL PCB
PUSH BUTTON
HARNESS
SCREW
◐PRECAUTION
◐FEATURES
1. Do not install the camera outdoors.
2. Choose an ideal location for the camera, since a camera unit must
be protected against moisture and vibration.
3. Be careful not to scratch the camera unit, especially lens or dome cover.
4. Use the camera within the temperature(-10℃ ~ 50℃).
5. Handle with care. Dropping it can cause serious damage to the camera.
6. Avoid any direct sun light toward the lens.
7.
1. Full HD(1920x1080P) image via HD-SDI interface with conventional
coaxial connection
2. Defog : Defog technology enhances visibility in real-time in fog,
smoke, lowlight, dust and etc. conditions
3. Smart IR : When IR LED is turned on in B/W, the objects can be
clearly identified due to the function that decreases screen
saturation of objects within a short distance
4. Adopted Smart DNR technology, It reduces noise efficiently in low
light condition
5. Provide Max. 64X digital zoom
6. Day & Night function(ICR)
7. Support 8 different privacy zone
8. This camera is incredibly flexible to install with its 3-axis camera
construction, which makes the camera ceiling, wall or slope
mountable
9. 25M range visible in total darkness with 24pcs of IR LEDs.(Indoor)
10. Multi-language full OSD support
Use the AC adaptor 12V DC or 24V AC, 1A.
If the product is to be put out of operation definitively,
take it to a local recycling plant for a disposal which
is not harmful to the environment.
PROTECTION SHEET
LATCH BUTTON
Ø100
Ø130.8 Ø109

◐SPECIFICATION
◐FUNCTION SETTING
1. How to use the jog lever
①SET :
② ③ :
④ ⑤ :
⑥EXT-VIDEO :
Used to access the menu and confirm selection.
UP, DOWN
LEFT, RIGHT
Used to move the cursor to up or down.
Used to move the cursor to left or right and change
the value.
Extra video output terminal for installation.
Plug your test monitor in hear. The cable is option.
3B25415A
2. OSD menu structure
※All specification is subject to change without notice to improve the quality.
Function
setting menu
MOTION
PRIVACY
LANGUAGE
DEFECT
RS485
VERSION
SHARPNESS
MONITOR
OSD
LSC
NTSC/PAL
FACTORY
SELECT
DISPLAY
SENSITIVITY
MOTION VIEW
DEFAULT
SELECT
DISPLAY
COLOR
DEFAULT
ENG, JPN,
CHN1, CHN2
LIVE DPC
LEVEL
STATIC DPC
START
LEVEL
SENS-UP
CAM ID
ID DISPLAY
BAUDRATE
SHARPNESS
LEVEL
RESOLUTION
CRT
LCD
TEXT OLOR
OUTLINE
Select the motion detection zone(1~3)
Display the zone or not and adjust the size &
position
Motion detection sensitivity setting
Select notification method of motion detection
Reset the setting of Motion Detection
Select the privacy zone(1~8)
Display the zone or not and adjust the size &
position
Select the mask color
Reset the setting of PRIVACY
Select the language
(English, Japanese, Chinese 1, Chinese 2)
Defective pixel compensation reflect real time
or not
LIVE DPC LEVEL setting
Appoint the defective pixel or not
Start defective pixels compensation
STATIC DPC LEVEL setting
SENSE-UP limit setting when finding defective
pixels
Select the camera ID for RS-485 communication
Display the CAM ID on the screen
Select baud rate
Firmware version display
Sharpness function ON / OFF
Increasing this value sharpens object edges
Enhances the image quality
Black Level : Contrast adjustable
Blue Gain : Blue gain adjustable
Red Gain : Red gain adjustable
Gamma : Gamma adjustable
Blue Gain : Blue gain adjustable
Red Gain : Red gain adjustable
OSD color selection
OSD outline
Use the brightness compensation of four lens'
corners(LSC) or not
NTSC/PAL selection
Reset your camera to factory default condition
Escape the menu
AUTO
X2~X60
AUTO/OFF
X2~X60
1~100
OFF, LOW,
MIDDLE, HIGH
OFF
BLC
HSBLC
DELAY
D→N(CDS)
N→D(CDS)
BURST
IR SMART
IR LED
IR PWM
S-LEVEL
E-LEVEL
FREEZE
MIRROR
D-ZOOM
NEG.IMAGE
Vari-focal auto iris DC lens
Vari-focal auto iris VIDEO lens
Fixed focal lens
Shutter speed auto adjustable
Select shutter speed manually
AGC level selectable
Using sense up when it is low luminance
Sense up limit setup(X2~X60)
Adjust the brightness
Widen DYNAMIC RANGE by gamma adjustment
Enhances visibility in fog, smoke, lowlight, dust
etc. conditions
Deactivates the BackLight function
Gain : BLC LEVEL setup
Area : BLC area setup
Default : Reset the setting of BLC
Hight light Suppress BLC setting
Select : Select HSBLC zone(1~4)
Display : Display the zone or not and adjust
the size & position
Level : Level adjust
Mode : Use the function at nightonly or all day
Black Mask : The function activate / deactivate
Default : Reset the setting of HSBLC
Adjust the white balance manually
Adjust the white balance automatically
Move the camera lens toward to white paper
then press the set button to find the optimal
white balance for current environment
Optimized White balance for Indoor
Optimized White balance for Outdoor
Select the duration time about changing the
day ↔ night mode(0~60)
Not adjustable
Not adjustable
Fixed at color(LED OFF)
Fixed at B/W
Determines whether to transmit the burst signal
or not in B/W mode
Decreases screen saturation of objects within
a short range
IR LED ON/OFF control
IR LED output level adjustable
Day & Night can be changed using external
signal(Not available)
Reducing noise by arithmetic processing of
pixels around
Reducing noise by arithmetic processing of time
Start level of 3DNR function
End level of 3DNR function
Noise Reduction sensitivity
Noise reduction activates depending on the
circumstances
Display the camera name on the screen
Still image
Flip the picture horizontally and/or vertically
PIP : Display the Picture in Picture image or not
D-Zoom : Use a digital zoom of X2 ~ X64
Pan&Tilt : Zoomed in image can be moved to
horizontal & vertical
Default : Reset the setting of Digital ZOOM
NEGATIVE image
1. LENS
2. EXPOSURE
3. WHITE BAL.
4. DAY&NIGHT
5. NR
6. SPECIAL
6. SPECIAL
7. ADJUST
8. RESET
9. EXIT
LOW, MIDDLE, HIGH
OFF, LOW, MIDDLE, HIGH
A : ORANGE(RX +)
B : WHITE(RX -)
Function
RX +
RX -
Remark
RS-485A
RS-485B
o.
A
B
N
3. How to control through RS-485 communication
4. Cable array
1) Match the camera with controller's ID, baudrate and protocol
2) Up, Down, Left and right of Jog lever is same as Up, Down, Left and
right of RS-485 controller
3) Enter of Jog lever is the same as menu key or IRIS open key of RS-
485 controller
Select menu Conte ntsSub menu
1/30(1/25)~1/50000
6
1
2
4
3
5
GST-2050
1/3" 2.1Megapixel CMOS
Progressive Scan
1944(H) x 1092(V) Pixel
50dB or More
1080P(1920 x 1080) 30fps
HD-SDI / 1.0 Vp-p(75Ω, Composite), NTSC/PAL(Selectable)
1.0Lux(Color), 0.5Lux(BW), 0.02Lux(Sens-up x60)
1/25 ~ 1/50,000sec
AWB / AWC-SET / MANUAL / INDOOR / OUTDOOR
BLC / HSBLC / OFF
LOW / MIDDLE / HIGH / OFF
LOW / MIDDLE / HIGH
SHARPNESS / MONITOR / LSC / NTSC/PAL
English, Japanese, Chinese(Selectable)
ICR(AUTO / COLOR / BW)
2DNR / 3DNR / SMART NR
ON / OFF(X2 ~ X64)
ON / OFF(8 Zone Selectable)
ON / OFF(3 Zone Selectable)
LIVE DPC / STATIC DPC
ON / OFF(Selectable limit ~ X60)
FREEZE / MIRROR / D-ZOOM / NEG.IMAGE
RS - 485(Baud Rate : 2400 ~ 38400)
Pelco-D
Vari-focal auto iris lens
12V DC/24V AC Dual voltage
Max. 600mA(at 12V DC, 24V AC) : LED ON
-10℃ ~ 50℃
-20℃ ~ 60℃
Ø130.8 x 101(H) mm
Approx. 500g
Model No.
Image Sensor
Effective Pixel
Privacy Zone
Communication
Power Supply
Scanning System
S/N Ratio
Video Output Mode
Video Output Level
Min. Illumination
Shutter Speed
White Balance
Backlight
ACCE(DWDR)
AGC
Adjustment
OSD
Day & Night
2D/3D-NR
Digital Zoom / PIP
Motion Detection
Defect Pixel Compensation
Sense-up
D-Effect
Protocol
Lens
Current Consumption
Operation Temp.
Preservation Temp.
Dimension
Weight
DC
VIDEO(N/A)
MANUAL
SHUTTER
AGC
SENSE-UP
BRIGHTNESS
ACCE
DEFOG
BACKLIGHT
MANUAL
ATW
AWC→SET
INDOOR
OUTDOOR
AUTO
COLOR
B/W
EXT
2DNR
3DNR
LEVEL
SMART NR
CAM TITLE
D-EFFECT