Orlaco 0208203 User manual

0208203
0208232
0208371
0208390
0208422
0208440
Monitor 7”LEDD
Installation manual
Manual No. IM0973260 A 01
11/2012
English
Art. No:

2IM0973260 A01
Safety
In order to guarantee safe operation, these safety
instructions must be read before you start using this
equipment.
• Do not open the enclosure. This can cause damage,
short-circuiting or electrical shocks.
• Do not expose the equipment to extreme temperatures.
This can cause deformation of the enclosure or damage
to internal components.
• Repairs may only be made by the manufacturer.
• The equipment must be installed as shown in this
manual.
Before you start using this equipment, please read this manual
carefully and follow all instructions. This installation manual
describes the installation of the equipment, outlines the connection
options and explains how to put the equipment into operation. We
recommend that you keep this manual in a safe place for reference
purposes.
If you have any questions or issues concerning the operation
of this equipment, consult the relevant section in the manual or
contact the Orlaco Products BV Service department.
The camera/display systems from Orlaco comply with the latest CE,
ADR, EMC and mirror-directive regulations. All products are ma-
nufactured in accordance with the ISO 9001 quality management
system, IATF 16949 quality automotive and ISO 14001 environ-
mental management systems
Contents page
1. LEDD variants 3
2. Monitor placement 3
3. Basic system installations 4
3.1 EMC 5
4. Technical specications 6
5. Assembly, connections and data LEDD 7
6. Maintenance and cleaning 13
7. Disposal 13
8. General terms and conditions 13
9. Version details 14
Monitor 7'' LEDD
Installation manual
Do not apply voltage to
the output power of the
monitor!

3
IM0973260 A01
1. LEDD variants
LEDD Art. No. Special feature Mask Video Cable Housing / Bracket Power Cable Page
Monitor 7” LEDD
2
0208203 Sun mask 2 metre
4 pin female w/o bracket 2 metre 7
Monitor 7” LEDD Serial 6
0208232 Sun mask 6 metre
7 pin female w/o bracket 6 metre 8
Monitor 7” LEDD CAN SRD 6
0208371 Sun mask 6 metre
7 pin female w/o bracket 6 metre 9
Monitor 7” LEDD PL 6
0208390* Sun mask 6 metre
4 pin female w/o bracket 6 metre 10
Monitor 7” LEDD PL 1 D
0208422* Sun mask 1 metre
6 pin female D w/o bracket 1 metre 8 pin male D 11
Monitor 7” LEDD Serial 2
0208440* Sun mask 2 metre
7 pin female w/o bracket 2 metre 12
*Dedicated OEM product, not for sale!
2. Monitor placement (guideline)
The correct placement of the monitor depends on the type of the vehicle.
Please take note of the following guidelines when installing the monitor.
Obstruction of the eld of vision
The monitor must be placed in such a way that the field of vision of sur-
rounding traffic and the work area is obstructed as little as possible.
Obstruction of the operation
The monitor may not obstruct the basic operation within the vehicle.
Viewing distance
View point on the monitor
Posture
View point on the monitor Viewing direction of the monitor
Installation manual
Bad
Good Moderate
0° 15° 30°
Bad
Good
Moderate
0°
10°
20°
15°
0°
30°
15°
30°
Good
Good
Moderate
Moderate
Bad
Bad
Moderate (incidental)
0°
40°
Bad
Good
Bad (continual)
40 cm 75 cm
150 cm
Moderate Bad
Bad Good
Bad
Good Moderate
0° 15° 30°
Bad
Good
Moderate
0°
10°
20°
15°
0°
30°
15°
30°
Good
Good
Moderate
Moderate
Bad
Bad
Moderate (incidental)
0°
40°
Bad
Good
Bad (continual)
40 cm 75 cm
150 cm
Moderate Bad
Bad Good
Bad
Good Moderate
0° 15° 30°
Bad
Good
Moderate
0°
10°
20°
15°
0°
30°
15°
30°
Good
Good
Moderate
Moderate
Bad
Bad
Moderate (incidental)
0°
40°
Bad
Good
Bad (continual)
40 cm 75 cm
150 cm
Moderate Bad
Bad Good
Bad
Good Moderate
0° 15° 30°
Bad
Good
Moderate
0°
10°
20°
15°
0°
30°
15°
30°
Good
Good
Moderate
Moderate
Bad
Bad
Moderate (incidental)
0°
40°
Bad
Good
Bad (continual)
40 cm 75 cm
150 cm
Moderate Bad
Bad Good
Bad
Good Moderate
0° 15° 30°
Bad
Good
Moderate
0°
10°
20°
15°
0°
30°
15°
30°
Good
Good
Moderate
Moderate
Bad
Bad
Moderate (incidental)
0°
40°
Bad
Good
Bad (continual)
40 cm 75 cm
150 cm
Moderate Bad
Bad Good

4
power
power
power
power
IM0973260 A01
3. Basic system installations
Two Camera System
One Camera System
Three Camera System
Four Camera System
Installation manual

5
IM0973260 A01
3.1 Electromagnetic compatibility installation instructions (EMC).
Preferred installation
Installation especially for forklifttrucks.
Warning! On vehicles with separated powerwiring like electrical forklifttrucks no other installation is allowed, the
screening may NOT in any way be connected to the battery:
Color/wire Function Vehicle connection:
Red wire +(plus) powersupply +(plus) voltage of the vehicle
(12..60V/Dc, 5A fuse)
White wire -(minus) GND powersupply -(minus) of the vehicle
Screening powercable Eliminate EMC disturbances Chassis of the vehicle
Alternative installation
If no separate 0V/minus is available on the vehicle and the minus of the battery is connected to the chassis of the
vehicle; connection is as follows:
Color/wire Function Vehicle connection:
Red wire +(plus) powersupply +(plus) voltage of the vehicle
(12..60V/Dc, 5A fuse)
White wire and
Screening powercable
-(minus) GND powersupply
and EMC
Chassis of the vehicle combined
with -(minus) of the vehicle
Preferred installation
Red wire
+ (Plus)
Power supply White wire
-(Minus) GND
Screening
To +(Plus) voltage
of the vehicle
To - (Minus)
of the vehicle
Red wire
+ (Plus)
Power supply
White wire
-(Minus) GND
Screening
To the chassis
and -(Minus)
of the vehicle
Alternative installation To +(Plus) voltage
of the vehicle
Connect screening to the chassis
and -(Minus) of the vehicle. Wire not included.
Connect screening to the chassis of the vehicle. Wire not included.
Installation manual

6IM0973260 A01
4. Technical specications
Type Automotive 7inch TFT liquid crystal display module LED backlight.
Resolution
WVGA 800xRGBx480 pixels.
Viewing
70° horizontal and 60° vertical (@ CR≥10).
LED Life Time
30000 Hrs.
Typical performance
Center luminance of white: 600cd/m2, Contrast ratio 650:1, Response time 5 ms (Tr).
Software menu
Full On-Screen-Display (OSD) functionality in 15 languages: English, Dutch, German, French, Czech, Hungarian, Italian, Polish,
Portuguese, Spanish, Turkish, Swedish, Finnish, Danish, Norwegian.
ABC mode
Improved Auto Brightness Control (ABC) including one-touch day/night setting and adjustable minimum and maximum
levels for automatic control.
Operating temperature
-40°C ..+85°C.
Storage temperature
-40°C ..+125°C.
Electrical
Input voltage range
12...60V
+/-10%.
Power consumption
Max 12W (only for the monitor, total power consumption depending on cameras and other peripherals)
Protection
>70V overvoltageprotection, <10V undervoltageprotection, protected against loaddumps, spikes and surges, reverse polarity
on all wiring.
Power-output
Nominal 2A +/-10% for powering cameras and other peripherals.
Video input
1Vtt, 75Ω, Pal 50 Hz, 4,43MHz color sub carr. NTSC 60 Hz, 3,58MHz color sub carr.
Mechanical
Surface
Hard coating (3H), with AG LR (Low Reflection) polarizer.
Housing
Color Black, material: aluminium & high impact automotive synthetic thermoplastic polymer.
Shock constancy
Shock and vibration resistant for usage on trucks, cranes, fork-lifts, maritime applications, machinery. Random vibration test
15,3G
rms at frequency: 24 to 2000, PSD (g²/Hz) 0,04 to 0,10.
Ingress protection
LEDD: IP54 according IEC60529 (Dust protected, protected against splashing water, 10L /min for 5 min)
Truck use
Withstand all fluids and materials used in and around trucks like: ammonia solution 5%, ethanol 80-100%, isopropanol
5-10%, soapy water (min. 50% soap per volume), alkaline degreasing compounds(used in high pressure washing equipment).
Certication
Quality & environment
Units are manufactured by Orlaco in the Netherlands; ISO 9001, ISO14001, ISO-TS16949.
Approvals
Approvals In compliance with all relevant EMC- and Automotive directives. Certificates available upon request.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Green Passport
All materials are compliant to Green Passport requirements according IMO resolution MEPC.197(62) as adopted on 15 July
2011 (Maritime sector: International Maritime Organization concerning the functions of the Marine Environment Protection
Committee).
Electrical
Input voltage range:
18...30V
+/-10%.
Power consumption:
Maximum 12W.
Protection:
>70V overvoltageprotection, <10V undervoltageprotection, protected against loaddumps, spikes and surges,
reverse polarity on all wiring.
Power-output:
For powering cameras and other peripherals. Power-output = input voltage. Output current 2A max.
Video input
1Vtt, 75Ω, Pal 50 Hz, 4,43MHz color sub carr. NTSC 60 Hz, 3,58MHz color sub carr.
Installation manual
*Different specications for the Serial displays
*
** Software menu
For the Radar Monitor Art. no. 0208371 applies; Software Menu Full On-Screen Display (OSD) functionality in 8 of languages: English,
Dutch, German, French, Italian, Polish, Spanish, Swedish.
**

7
IM0973260 A01
5. Assembly, connections and data LEDD
Article numbers: 0208203
Cables / Connectors 2m multicable (power) open wired, 2m multicable (video) with 4p molded female connector
Art. No.: 8975171
Weight
1,1kg (monitor, cables and connector)
120
objects in
monitor are
closer than
they appear
units in mm
188
Min. bend radius= 50mm
R = 50
DDIN opening
(acc. to ISO 7736)
183
113,5
181
53,1 46,5
112,5
objects in
monitor are
closer than
theyappear
2000
2000
objects in
monitor are
closer than
they appear
4
1
23
Connections to the monitor: (Secure the power input with a 5A fuse)
1 = Red = Power input: 12...60V/DC
2 = White = Power input: 0V
3 = Blue = Cam No. 1 activated at 3...60V/DC
4 = Brown = Cam No. 2 activated at 3...60V/DC
5 = White/Yellow = Cam No. 3 activated at 3...60V/DC
6 = Grey = Cam No. 4/Speedometer/Tachograph/Zoom in
7 = Yellow = Parking Brake (only Front Cam)/Zoom out
Front side 4p female molded connector:
1 = Coax core = Video in
2 = Coax shielding = Video 0V
3 = Red = Power output: 12V/DC
4 = Black = Power output: 0V
Shielding = Ground
1
2
3
7
456
Connect instructions: Please refer to your Orlaco system documentation or chapter 3 “Basic System Installations”.
User instructions: Please refer to usermanual no: UM0972080 for operation.
objects in
monitor are
closer than
they appear
objects in
monitor are
closer than
they appear
objects in
monitor are
closer than
they appear
objects in
monitor are
closer than
they appear
1
Disassembling of the LEDD monitor (from dashboard):
234
Remove the suncover by
sliding it upwards in the arrow
direction and then forwards.
Insert the U shaped demounting
tool into the holes as shown.
Tweak the dismounting tool in both
holes & pull the screen slightly out
of the dashboard. Pay attention to
step 4 before completely removing
the screen from the dashboard.
Do the same thing on the
other side.
Installation manual

8IM0973260 A01
Cables / Connectors Cable LEDD 6m serial (power) open wired, 6m multicable (video) with 7p female M16 OEM
molded connector. Art. No.: 8975180
Weight
1,2kg (monitor, cables and connector)
120
188
R = 50
DDIN opening
(acc. to ISO 7736)
183
113,5
181
53,1 46,5
112,5
objects in
monitor are
closer than
they appear
6000
6000
Units in mm
Min. Bend radius = 50mm
objects in
monitor are
closer than
they appear
Connections to the monitor: (Secure the power input with a 5A fuse)
1 = Red = Power input: 18...30V/DC
2 = White = Power input: 0V
3 = Blue = Cam No. 1 activated at 3...60V/DC
4 = Brown = Cam No. 2 activated at 3...60V/DC
5 = White/Yellow = Cam No. 3 activated at 3...60V/DC
6 = Grey = Cam No. 4/Speedometer/Tachograph/Zoom in
7 = Yellow = Parking Brake (only Front Cam)/Zoom out.
Front side 7p female molded connector
1 = Coax core = Video in
2 = Coax shielding = Video 0V
3 = Red = Power output: equal to “Power input”
4 = Black = Power output: 0V
5 = Orange = RS232 Rx
6 = Yellow = RS232 Tx
7= Grey = RS232 Rx & Tx 0V
1
2
3
7
456
2
5
7
43
61
Article number: 0208232
objects in
monitor are
closer than
they appear
objects in
monitor are
closer than
they appear
objects in
monitor are
closer than
they appear
objects in
monitor are
closer than
they appear
1
Disassembling of the LEDD monitor (from dashboard):
234
Remove the suncover by
sliding it upwards in the arrow
direction and then forwards.
Insert the U shaped demounting
tool into the holes as shown.
Tweak the dismounting tool in both
holes & pull the screen slightly out
of the dashboard. Pay attention to
step 4 before completely removing
the screen from the dashboard.
Do the same thing on the
other side.
Connect instructions: Please refer to your Orlaco system documentation or chapter 3 “Basic System Installations”.
User instructions: Please refer to usermanual no: UM0972080 for operation.
Installation manual

9
IM0973260 A01
Installation manual
Cables / Connectors Cable LEDD 6m serial (power) open wired, 6m multicable (video) with 7p female M16 OEM
molded connector. Art. No.: 8975180
Weight
1,2kg (monitor, cables and connector)
objec ts in
monitor are
closer than
they appear
Connections to the monitor:(Secure the power input with a 5A fuse)
1 = Red = Power input: 12...60V/DC
2 = White = Power input: 0V
3 = Blue = Cam No. 1 activated at 3...60V/DC
+ Activation Radar on sensor direction 5,6 and 7
4 = Brown = Cam No. 2 activated at 3...60V/DC
+ Activation Radar on sensor direction 1,11 and 12
5 = White/Yellow = Cam No. 3 activated at 3...60V/DC
6 = Grey = Cam No. 4 activated at 3...60V/DC
+ Blocking sensor directions 2,3,4 and 8,9,10
7 = Yellow = Quad view, Parking Brake (only Front Cam)/Zoom out
Front side 7p female molded connector:
1 = Coax core = Video in
2 = Coax shielding = Video 0V
3 = Red = Power output: equal to “Power input”
4 = Black = Power output: 0V
5 = Orange = CAN-L
6 = Yellow = CAN-H
7= Grey = N.C.
1
2
3
7
456
2
5
7
43
61
120
units in mm
188
Min. bend radius= 50mm
R = 50
DDIN opening
(acc. to ISO 7736)
183
113,5
181
53,1 46,5
112,5
objects in
monitor are
closer than
they appear
6000
6000
Controller Area Network (CAN)
Pair of signal wires (CAN_H and CAN_L)
Article number: 0208371
objects in
monitor are
closer than
they appear
objects in
monitor are
closer than
they appear
objects in
monitor are
closer than
they appear
objects in
monitor are
closer than
they appear
1
Disassembling of the LEDD monitor (from dashboard):
234
Remove the suncover by
sliding it upwards in the arrow
direction and then forwards.
Insert the U shaped demounting
tool into the holes as shown.
Tweak the dismounting tool in both
holes & pull the screen slightly out
of the dashboard. Pay attention to
step 4 before completely removing
the screen from the dashboard.
Do the same thing on the
other side.
Connect instructions: Please refer to your Orlaco system documentation or chapter 3 “Basic System Installations”.
User instructions: Please refer to usermanual no: UM0972080 for operation.

10 IM0973260 A01
Cables / Connectors 6m multicable (power) open wired, 6m multicable (video) with 4p molded female connector
Art. No.: 1001232
Weight 1,2kg (monitor, cables and connector)
objects in
monitor are
closer than
they appear
4
1
23
Connections to the monitor: (Secure the power input with a 5A fuse)
1 = Red = Power input: 12...60V/DC
2 = White = Power input: 0V
3 = Blue = Cam No. 1 activated at 3...60V/DC
4 = Brown = Cam No. 2 activated at 3...60V/DC
5 = White/Yellow = Cam No. 3 activated at 3...60V/DC
6 = Grey = Cam No. 4/Speedometer/Tachograph/Zoom in
7 = Yellow = Parking Brake (only Front Cam)/Zoom out
Front side 4p female molded connector:
1 = Coax core = Video in
2 = Coax shielding = Video 0V
3 = Red = Power output: 12V/DC
4 = Black = Power output: 0V
Shielding = Ground
1
2
3
7
456
120
units in mm
188
Min. bend radius= 50mm
R = 50
DDIN opening
(acc. to ISO 7736)
183
113,5
181
53,1 46,5
112,5
objects in
monitor are
closer than
they appear
6000
6000
Article number: 0208390
objects in
monitor are
closer than
they appear
objects in
monitor are
closer than
they appear
objects in
monitor are
closer than
they appear
objects in
monitor are
closer than
they appear
1
Disassembling of the LEDD monitor (from dashboard):
234
Remove the suncover by
sliding it upwards in the arrow
direction and then forwards.
Insert the U shaped demounting
tool into the holes as shown.
Tweak the dismounting tool in both
holes & pull the screen slightly out
of the dashboard. Pay attention to
step 4 before completely removing
the screen from the dashboard.
Do the same thing on the
other side.
Connect instructions: Please refer to your Orlaco system documentation or chapter 3 “Basic System Installations”.
User instructions: Please refer to usermanual no: UM0972080 for operation.
Installation manual

11
IM0973260 A01
Installation manual
Cables / Connectors 1m multicable (power) with 8p male Deutsch connector, 1m multicable (video) with 6p female Deutsch
connector. Art. No.: 8976311.
Weight 1,1kg (monitor, cables and connectors).
objec ts in
monitor are
closer than
they appear
1
2
3
45
6
7
8
4
5
61
2
3
Back side Deutsch 8p male to the monitor:
(Secure the power input with a 5A fuse)
1 = Red = Power input: 12...60V/DC
2 = White = Power input: 0V
3 = Blue = Cam No. 1 activate at 3..60V/DC
4 = Brown = Cam No. 2 activate at 3..60V/DC
5 = White/Yellow = Cam No. 3 activate at 3..60V/DC
6 = Grey = Aux 1
7 = Yellow = Aux 2
8(B) = Shielding = Ground, connected to 5(A)
Back side Deutsch 6p female connector:
1 = Coax core = Video in
2 = Coax shielding = Video 0V
3 = Red = Power output: 12V/DC
4 = Black = Power output: 0V; connected to 6
5(A) = Shielding = Ground, connected to 8(B)
6 = Orange = Mirror
120
objects in
monitor are
closer than
they appear
units in mm
188
DDIN opening
(acc. to ISO 7736)
183
113,5
181
53,1 46,5
112,5
1000
1000 Min. bend radius= 50mm
R = 50
Article number: 0208422
objects in
monitor are
closer than
they appear
objects in
monitor are
closer than
they appear
objects in
monitor are
closer than
they appear
objects in
monitor are
closer than
they appear
1
Disassembling of the LEDD monitor (from dashboard):
234
Remove the suncover by
sliding it upwards in the arrow
direction and then forwards.
Insert the U shaped demounting
tool into the holes as shown.
Tweak the dismounting tool in both
holes & pull the screen slightly out
of the dashboard. Pay attention to
step 4 before completely removing
the screen from the dashboard.
Do the same thing on the
other side.
Connect instructions: Please refer to your Orlaco system documentation or chapter 3 “Basic System Installations”.
User instructions: Please refer to usermanual no: UM0972080 for operation.

12 IM0973260 A01
Installation manual
Cables / Connectors Cable LEDD 2m serial (power) open wired, 2m multicable (video) with 7p female M16 molded OEM
connector. Art. No.: 1002051
Weight 1,1kg (monitor, cables and connector)
objects in
monitor are
closer than
they appear
1
2
3
7
456
2
5
7
43
61
Connections to the monitor: (Secure the power input with a 5A fuse)
1 = Red = Power input: 18...30V/DC
2 = White = Power input: 0V
3 = Blue = Cam No. 1 activated at 3...60V/DC
4 = Brown = Cam No. 2 activated at 3...60V/DC
5 = White/Yellow = Cam No. 3 activated at 3...60V/DC
6 = Grey = Cam No. 4/Speedometer/Tachograph/Zoom in
7 = Yellow = Parking Brake (only Front Cam)/Zoom out.
Front side 7p female molded connector:
1 = Coax core = Video in
2 = Coax shielding = Video 0V
3 = Red = Power output: equal to “Power input”
4 = Black = Power output: 0V
5 = Orange = RS232 Rx
6 = Yellow = RS232 Tx
7= Grey = RS232 Rx & Tx 0V
120
188
R = 50
DDIN opening
(acc. to ISO 7736)
183
113,5
181
53,1 46,5
112,5
objects in
monitor are
closer than
they appear
2000
2000
Units in mm Min. Bend radius = 50mm
Article number: 0208440
objects in
monitor are
closer than
they appear
objects in
monitor are
closer than
they appear
objects in
monitor are
closer than
they appear
objects in
monitor are
closer than
they appear
1
Disassembling of the LEDD monitor (from dashboard):
234
Remove the suncover by
sliding it upwards in the arrow
direction and then forwards.
Insert the U shaped demounting
tool into the holes as shown.
Tweak the dismounting tool in both
holes & pull the screen slightly out
of the dashboard. Pay attention to
step 4 before completely removing
the screen from the dashboard.
Do the same thing on the
other side.
Connect instructions: Please refer to your Orlaco system documentation or chapter 3 “Basic System Installations”.
User instructions: Please refer to usermanual no: UM0972080 for operation.

13
objects in
monitor are
closer than
they appear
IM0973260 A01
Installation manual
6. Maintenance and cleaning
First, do not touch the screen with your fingers. The underlying
transistors will react to the static electricity in your fingers, or may
get damaged by the pressure thus exerted. This will eventually
produce dead pixels; tiny, inoperative, or colored dots impairing
picture quality.
So take care when cleaning your delicate LCD Screen. Use a high
quality and safe foam cleaner and a soft cloth. Do absolutely not
use aggressive chemicals or abrasive cleaning agents.
7. Disposal
Disassembly, removal and disposal. Local regulations for dealing
with waste must be followed when disposing of disassembled
components or entire units.
8. General terms and conditions
Orlaco Products BV is not liable for damage resulting from
inadequate servicing, incorrect usage or alterations made to the
equipment without informing the manufacturer in writing.
This installation manual has been made available by Orlaco
Products BV. All rights reserved. No part of this manual may be
reproduced and/or made public in printed form, in photocopy
form or on microfilm, or in any other way, without the prior
written permission of Orlaco. This also applies to the associated
drawings and figures.
Orlaco reserves the right to make changes to components at any
time without informing customers beforehand or directly.
All dimensions given are for commercial purposes.
For information regarding repairs that is not covered in this
manual, please contact the Orlaco Products BV service department.
This manual has been prepared with all due care and attention.
However, Orlaco Products BV cannot be held responsible for any
errors in this manual or any consequences thereof.

14 IM0973260 A01
Installation manual
9. Version details
Version R1-0. First issue November 2012.
Version R1-1. Connections changed Art. No. 0208371, March 2013.
Version R1-2. Chapter 4: Specifications text added, July 2013.
Version R1-3. Monitor Art. No. 0208422 added, December 2013.
Version R1-4. Barcode added, September 2014.
Version R1-5. Chapter 4 Specifications adjusted, April 2015.
Version A 01. Monitor Art. No. 0208440 added, page 12, October 2018.

15
IM0973260 A01
Installation manual

ORLACO
www.orlaco.com
Orlaco is a Manufacturing company that specializes in making
cameras and monitor systems for commercial vehicles, fork-lift
trucks, cranes, off shore and maritime.
Our objective is to design and produce camera systems for the
professional market that improve the drivers’ view and increase
operating efficiency.
At our facility in Barneveld we locate our design, manufacturing,
warehousing and service department.
Vision is our mission®. Orlaco therefore deploys the development,
manufacture, supply and service of camera and Monitor systems
that will improve safety and efficiency of all vehicles,
machinery and vessels. Our systems give the end user a view on
each blind spot and will create comfort and improved working
conditions. Our active approach will support market demands
and innovations and will lead to enthusiastic ambassadors in the
market; our customers.
For more information: www.orlaco.com