Orno OR-VID-JS-1053/W Specification sheet

ARCUS RFID VIDEO-DOORPHONE SET
OPERATING AND INSTALLATIONS MANUAL
Model: OR-VID-JS-1053/W; OR-VID-JS-1053/B

Monitor 7” TFT-LCD External panel
with camera
Camera accessories Monitor accessories
Operating instructions Power supply
for the socket
Cable Mounting screws
Please read this manual carefully before connecting and using the device. In case something written herein is unclear,
please contact the seller. Installation and commissioning of the equipment by the customer are possible if the installer has
basic knowledge of electrical systems and the use of proper tools. Nevertheless, the device installation by qualified
personnel is recommended.
The manufacturer is not responsible for any damage that can result from improper device installation or operation.
Any repair or modification carried out by yourselves results in loss of guarantee.
In view of the fact that the technical data are subject to continuous modifications, the manufacturer reserves a right to make
changes to the product characteristics and to introduce different constructional solutions without deterioration of the product
parameters or functional quality.
Additional information about ORNO products are available at www.orno.pl. Orno-Logistic Sp. z o.o. holds no responsibility
for the results of non-compliance with the provisions of the present Manual. Orno Logistic Sp. z o.o. reserves the right to
make changes to the Manual - the latest version of the Manual can be downloaded from www.orno.pl. Any
translation/interpretation rights and copyright in relation to this Manual are reserved.
1. Disconnect the power supply before performing any activities.
2. Do not immerse the product in water or other liquids.
3. Do not operate the device with damaged housing.
4. Do not open or repair the device yourself.
5. Do not use the device contrary to its dedication.
6. After installation and mounting, remove the protective foil from the monitor screen!
Proximity
tags
TABLE OF CONTENTS
Set characteristics ..............................................................................................
Set construction ..................................................................................................
Installation ..........................................................................................................
Wiring diagrams .................................................................................................
Operation ............................................................................................................
Problem solving ..................................................................................................
Cleaning and maintenance .................................................................................
Technical data ....................................................................................................
3
3
4
5
7
8
9
9
SET EQUIPMENT

The video-doorphone is designed for installation in 1 family buildings.
Functions:
- talking to and observing the person at the entrance;
- direct control of the electric door strike;
- possibility to control the gate;
- infrared diode lighting for night vision;
- smooth adjustment of the monitor parameters (picture brightness, call and ringing volume);
- proximity card and tags reader.
The most important features:
- high quality colour hidden pin-hole camera;
- vandal resistant camera housing for surface mounting (protective cover included);
- 7" colour LCD display;
- touchscreen, backlit display buttons;
- memory module for storing 20 colour images in automatic mode;
- 4-wires installation and 2 wires of electric strike, which does not require additional power supply.
The set can be extended with an additional monitor and external panel with a JS camera.
Wicket opening
Microphone
Power supply DC13,5V
Gate control
LK1/LK2
Loudspeaker
Display
Gate opening
Preview/conversation
Ringtone selection
Brightness adjustment
Call volume adjustment
Ringtone volume
adjustment
Viewing photos
Connection cable for gate control
Connecting external
panels
1. Monitor
SET CHARACTERISTICS
SET CONSTRUCTION

IR illumination
Call button
Loudspeaker
Microphone
Camera
2. External panel with camera
Proximity
card and tags
reader Reset button
for ID media
INSTALLATION
We recommend that you perform a functional test of the device before making the mounting holes. To do
so, connect the device for a test according to the wiring diagram. The first person holding the camera
should call the second person at the monitor using the button. This person should carefully examine the
field of view of the camera in order to correct the position of the module if necessary. After accurate
measurements, the mounting holes should be made with the power off.
1. Monitor
The optimum height of the monitor is 140-170 cm to suit individual needs.
1. Screw the supplied mounting frame to the wall.
2. Connect individual cables to the terminals on the back of the monitor
according to the connection diagram.
3. Hang the monitor on the mounting frame.
4. Plug the power supply into the socket.

110-240V~
Camera
2 wires
4 wires
2 wires
Monitor
Electric strike
2 żyły
Gate
control
Important!
It is forbidden to make connections to live devices!
Failure to comply with the above recommendation may lead to permanent damage to the device and loss of health.
The set does not include connecting cables, electric door strike and automatic gate unit.
13.5VDC
5
(1)Surface mounting
(2)Corner-surface mounting
wall
wall
0
30
0
33
30 cm
27cm
1. Screw the protective cover to the external panel.
2. Drill two holes in the wall/post.
3. Place the mounting dowels in the prepared holes.
4. Place the external panel on the installation site.
5. Tighten the fastening screws.
1. External panel with camera
The correct location of the outdoor panel determines the
comfort of use. Remember not to choose your location with
high sunshine and exposed to heavy precipitation.
The camera should be installed at a height of 1.4 ~1.7 m.
WIRING DIAGRAMS

6
While designing the wiring system, take into account the suitable cross-section of cables:
2
up to 30 m - recommended cable XzTKMXpw 3 x 2 x 0,5 mm
2
from 30 m to 100 m - recommended cable XzTKMXpw 3 x 2 x 0,8 mm
2
The connection to the electromagnetic lock should be made with 2 x 1 mm .
Any electric door strike with a supply voltage of 12VDC and current consumption of max. 500 mA.
The total length of the installation must not exceed 100 meters.
The use of twisted-pair cables is absolutely not recommended.
The video doorphone cables should not be routed in one cable with the cables of other installations such as
bell, alarm, etc. Any power and telecommunication cables emitting strong magnetic fields (e.g.
loudspeaker columns, TV set) in direct contact with the cables connecting the external panel to the monitor
may adversely affect the operation of the set.
power
supply
13.5VDC
Monitor
Camera
Electric strike
Gate
control
Red
B+
Yellow
V
White
A
Black
G
The set does not include an additional monitor, external panel with camera and electric door strike!
1. Connection diagram of the monitor and external panel with the camera
POWER SUPPLY - red
VIDEO - yellow
AUDIO - white
MASA - black

7
To open the gate, in conversation mode
touch the Gate opening button
Observation of the environment -
in standby mode, touch the button
Preview/conversation
To start the conversation press the button
Preview/conversation
If the conversation is not started, the picture
is automatically switched off after 60 seconds.
To open the wicket, touch the
Wicket opening button
in conversation mode
6
1. Answering calls
Pressing the call button on the external panel will cause the monitor to beep and the image of the visitor will appear on the
screen. To start a conversation, use the button on the monitor panel.
The call and preview function will remain active for approximately 60 seconds, after which the image will automatically
switch off.
OPERATION
Press call button Light up the monitor screen,
which will display the picture
of the caller. Automatically
save the visitor's picture.

8
2. Preview/monitoring
In the monitor standby mode, use the button .
3. Working time
a) connection time: about 60 seconds
b) talk time: about 60 seconds
c) preview time: about 60 seconds
4. Remote opening of the wicket
If an electric door strike is connected to the device, it is possible to open the door remotely.
For this purpose, use the button on the monitor panel during conversation or viewing.
5. Remote opening of the gate
If an automatic gate is connected to the unit, it can be opened remotely from the monitor panel. To do so, use the button
6. Changing the melody of the bell
Press the RINGTON SELECTION button to enter the settings, and then press the same button again to change the
sound. Confirm the change with the PREVIEW/CONVERSATION button .
There are 9 ringtones to choose from.
7. Other functions
With the potentiometers on the bottom of the monitor, you can adjust the call volume, ring volume and picture
brightness.
8. Programming tags/proximity cards
The device is equipped with a function of opening the entrance with a special key ring (card).
A
Prepare two key rings - red and grey. One of them - RESET KEY (red) - deletes the user's active key ring,
The second one - ADDING KEY (grey) - programs pendants for use. Make sure to describe them correctly.
B
When the video door intercom is on, press the RESET button at the back of the camera's external panel, you will hear
6-times a beep. Put the red key ring on the reader area, you will hear 1 short beep. Then put the grey key ring on the reader
area and you will hear a single long beep. This way the pendants will be programmed and there will be no need to use the
RESET button after mounting the camera. An exception is if you lose the programming key ring.
C
To add a user, first put ADDING KEY in the reader zone - you will hear a 4-times beep and then the key ring you want to
add. The key ring will be programmed and you will hear a single beep as you use it. The device supports RESET and
ADDING key rings and 4 user key rings. It will not be possible to add more.
D
RESET key rings: put the RESET KEY key ring in the reader zone, you will hear a 4-times beep, this will delete all used key
rings. Then put ADDING KEY on to the reader to program new key rings. If no action is performed within 10 seconds after
applying the RESET key ring, the key rings will remain programmed and will work as before.
PROBLEM SOLVING
1. No sound while calling
a. The connection cable between monitor and camera is loose.
b. The volume has be turn to the end.
2. Unclear image
Please check if the brightness is turned to too down, please adjust the
brightness knob.

working: < 2W
-15°C ~ +50°C
43.2 x 140.6 x 29.3 mm
External panel with camera
0.65 kg
0
diagonal approx. 44
9
3. In the image, numerous interferences, no synchronicity (image blinks)
a) the connection cable has a cross-section not matching the length
b) connection too long - use shielded cable
c) poor cable quality
d) strong source of electromagnetic interference - use shielded cable
4. The audio on the monitor is coupling
a) check your installation for technical requirements,
b) check that the installation is not exposed to water and moisture etc.
5. The electric strike does not open every time
a) check the independent operation of the electric strike
6. Scratched monitor
a) check that the protective film is removed from the screen
CLEANING AND MAINTENANCE
The dirt should be cleaned with a soft, slightly damp cloth with the addition of mild cleaning agents
intended for plastic. Do not use cleaning agents based on solvents, petrol, etc. or agents containing
abrasive substances.
TECHNICAL DATA*
(from monitor)
Power supply:
Camera type:
Viewing angle:
Power consumption:
Working temperature:
Night-time lighting:
Dimensions:
Net weight:
colourful
IR diodes

*The manufacturer reserves the right to make changes to technical parameters without prior notice.
standby: < 1,5W; working: <8W
800 x 480
50
240 x 114 x 12 mm
7
0.33 kg
10
ORNO-LOGISTIC Sp. z o.o.
ul. Rolników 437, 44-141 Gliwice, tel. [phone], www.orno.pl
(11/2020)
PRODUCER
Power supply:
Monitor type:
Display:
Power consumption:
Resolution:
Working temperature:
Dimensions:
Net weight:
colourful, hands-free
Each household is a user of electrical and electronic equipment, and hence a potential producer of hazardous waste for
humans and the environment, due to the presence of hazardous substances, mixtures and components in the equipment.
On the other hand, used equipment is valuable material from which we can recover raw materials such as copper, tin, glass,
iron and others. The weee sign placed on the equipment, packaging or documents attached to it indicates the need for
selective collection of waste electrical and electronic equipment. Products so marked, under penalty of fine, cannot be
thrown into ordinary garbage along with other waste.
The marking means at the same time that the equipment was placed on the market after August 13, 2005. It is the responsibility of the
user to hand the used equipment to a designated collection point for proper processing. Used equipment can also be handed over to the
seller, if one buys a new product in an amount not greater than the new purchased equipment of the same type. Information on the
available collection system of waste electrical equipment can be found in the information desk of the store and in the municipal office or
district office. Proper handling of used equipment prevents negative consequences for the environment and human health!